期刊文献+
共找到3篇文章
< 1 >
每页显示 20 50 100
加工内孔沉割槽的偏心差动刀具
1
作者 李代华 《工具技术》 北大核心 1991年第8期34-34,36,共2页
加工如图1所示的整体式活塞杆杆头内孔沉割槽,当L小于500mm时,用1m立式车床加工,当L大于500mm时,1m立式车床上放不下工件,不能加工,因此设计了如图2所示的偏心差动加工内孔沉割槽机构,解决了L大于500mm的整体式活塞杆杆头内孔沉割槽的... 加工如图1所示的整体式活塞杆杆头内孔沉割槽,当L小于500mm时,用1m立式车床加工,当L大于500mm时,1m立式车床上放不下工件,不能加工,因此设计了如图2所示的偏心差动加工内孔沉割槽机构,解决了L大于500mm的整体式活塞杆杆头内孔沉割槽的加工问题。 展开更多
关键词 内孔沉割槽 偏心差动刀具 立式铣床
下载PDF
机器人用RV减速器的瞬心特性和受力分析 被引量:2
2
作者 李端玲 王允地 +1 位作者 樊养余 张明中 《机械科学与技术》 EI CSCD 北大核心 2001年第6期860-861,880,共3页
为深入认识 RV减速器的工作原理 ,研究了该机构的瞬心特性 ,并在机构组成的基础上进行了受力分析 ,结果表明 :瞬心位置与行星轮中心的距离为一常数 ,瞬心的力学意义相当于一固定铰链 ;运动中驱动力大小分布不均匀 。
关键词 传动机构 摆线轮 行星轮 力学分析 瞬心特性 偏心差动 机器人 减速器
下载PDF
Aerodynamic effects of impeller-diffuser axial misalignment in low-flow-coefficient centrifugal compressor 被引量:1
3
作者 WANG ZhiHeng XI Guang LIU QingFang 《Science China(Technological Sciences)》 SCIE EI CAS CSCD 2015年第1期29-36,共8页
A numerical investigation on the aerodynamic effects of impeller-diffuser axial misalignment in the low-flow-coefficient centrifugal compressor is conducted through three-dimensional CFD analysis.The results show that... A numerical investigation on the aerodynamic effects of impeller-diffuser axial misalignment in the low-flow-coefficient centrifugal compressor is conducted through three-dimensional CFD analysis.The results show that the flow,especially near the diffuser inlet,is influenced by the axial misalignment obviously.When the impeller offsets to one side,the pressure at diffuser inlet close to this side will descend,and the vortex in the cavity on the other side will partially enter the diffuser and then result in the back flow.The performances of the stage and its components also change with the impeller-diffuser axial misalignment.There exists an optimum offset making the efficiency maximum at a given operating point.Furthermore,the effect of impeller-diffuser axial misalignment on the axial thrust is pronounced.The axial thrust is nearly increased linearly with the increase of axial misalignment.The aerodynamic effects of impeller-diffuser axial misalignment in the low-flow-coefficient centrifugal compressor behaves more remarkably at the large flow rate.To alleviate the aerodynamic effects of impeller-diffuser misalignment,a rounding in the meridional plane at the diffuser inlet can be applied. 展开更多
关键词 MISALIGNMENT COMPRESSOR low flow coefficient IMPELLER
原文传递
上一页 1 下一页 到第
使用帮助 返回顶部