Optical microscopy, and scanning electron microscopy in conjunction with energy dispersed X-ray spectrometry （SEM-EDX）, have been used to study the minerals and the concentrations of 12 trace elements in the No.14 c...Optical microscopy, and scanning electron microscopy in conjunction with energy dispersed X-ray spectrometry （SEM-EDX）, have been used to study the minerals and the concentrations of 12 trace elements in the No.14 coal from the Huolinhe mine, Inner Mongolia China. The distribution, affinity and removability of the trace elements were studied by float-sink experiments and petrological methods. A high mineral content, dominated by clay minerals, was found in the No.14 coal from the Huolinhe mine. The concentrations of As, Sb and Hg are relatively high compared to the average values for Chinese coals. As, Cr, Hg, Li, Mn, Pb are mainly associated with the minerals while Cd, Co, Ni, Sb, and Se are evenly distributed between the minerals and the organic matter. Be and Ba are mainly distributed in the minerals with a minor proportion in the organic matter. Most elements have a low organic affinity, although Sb, Se, Co, Cd, Ni are closely integrated with the organic matter. High theoretical removabilities are indicated for most trace elements. So it may be possible to lower the concentrations of trace elements during coal preparation.展开更多
Mg-1.5Zn-0.2Zr-xCe (x=0, 0.1, 0.3, 0.5, mass fraction, %) alloys were prepared by conventional semi-continuous casting. The effect of rare earth Ce on the microstructure of Mg-1.5Zn-0.2Zr-xCe alloys was studied and th...Mg-1.5Zn-0.2Zr-xCe (x=0, 0.1, 0.3, 0.5, mass fraction, %) alloys were prepared by conventional semi-continuous casting. The effect of rare earth Ce on the microstructure of Mg-1.5Zn-0.2Zr-xCe alloys was studied and the distribution of Ce was analyzed by optical microscopy (OM), X-ray diffractometry (XRD) and scanning electron microscopy (SEM). The results indicate that Ce element exists in the form of Mg12Ce phase and has an obvious refining effect on the microstructure of test alloys. As the Ce content increases, the grain size reduces, the grain boundaries turn thinner, and the distribution of Mg12Ce precipitates becomes more and more dispersed. The Mg-1.5Zn-0.2Zr alloy with 0.3%Ce has the best refinement effect. From center to periphery of the ingot, the amount of granular precipitates in the grain reduces. In longitudinal section of the ingot, some relative long columnar grains appear.展开更多
A combination of NAA and micro-PIXE was used to study concentrations and distributions of platinum group elements (PGE) in ores from Xinjie Cu-Pt deposit.The NAA results of the bulk indicate that the ores belong to th...A combination of NAA and micro-PIXE was used to study concentrations and distributions of platinum group elements (PGE) in ores from Xinjie Cu-Pt deposit.The NAA results of the bulk indicate that the ores belong to the enriched Pt-Pd type.The element concentration maps of scanning micro-PIXE for the ores show that the occurence form of Pt is independent arsenide minerals. No PGE were detected in chalcopyrite of Xinjie Cu-Pt deposit. These information are economically beneficial to the mineral smelting process.展开更多
We explored the potential use of combining wavelength-dispersive X-ray spectroscopy(WDX) and micromorphology of thin sections to identify minerals in peat soils. Peat soil minerals from three peats and swamps across G...We explored the potential use of combining wavelength-dispersive X-ray spectroscopy(WDX) and micromorphology of thin sections to identify minerals in peat soils. Peat soil minerals from three peats and swamps across Golestan Province in northern Iran were first characterized by micromorphological studies. Soils were composed mainly of quartz, muscovite, biotite, pyroxene,sericitized Fe-nodules, and iron-rich garnet. In addition,micromorphological results indicated that Galougah Coastal Swamp sections contained some inorganic residue with biological origin including oyster and limpet, which may be related to the swamp's location near Gorgan Gulf.In order to determine mineralogical properties of samples,twelve unknown grains were chosen for elemental concentration map studies. Quartz, garnet, ilmenite, calcite,and pyroxene in Suteh samples; epidote and Fe-nodule in Ghaleh-Ghafeh Peat Swamp; and barite, phyllosilicates,and calcite in Galougah were identified by WDX mapping of Si, Al, Fe, Ca, Mg, C, Ba, S, and Ti. Composition of the oysters' body was also analyzed by WDX for Si, Ca, Fe,and C. The results indicated that most of the minerals in all sections likely formed through weathering, inheriting their composition from the parent rock. This research suggests that merging micromorphology and SEM/WDX image techniques can be useful in confirming the presence of mineral particles in soil science.展开更多
Effect of element cerium （Ce） on microstructure and mechanical properties of A1-Zn-Mg-Cu alloys has been investigated by transmission electron microscopy （TEM）, scanning electron microscopy （SEM）, differential s...Effect of element cerium （Ce） on microstructure and mechanical properties of A1-Zn-Mg-Cu alloys has been investigated by transmission electron microscopy （TEM）, scanning electron microscopy （SEM）, differential scanning calorimetry （DSC） and hardness test. The results show that addition of Ce can remarkably refine the as-cast grains and eutectic microstructure. A transformation from Mg（Zn,Cu,A1）2 phase to A12CuMg phase is observed during homogenization. Furthermore, the Ce addition introduces changes in the precipitation process and consequently in the age-hardening behavior of the alloy. Microstructural measurements reveal that the addition of Ce promotes the precipitation of η＇ phase, but it also partly retards the precipitation of GP zones. The density of precipitates decreases in a certain degree and rod-like η＇ precipitates increase when Ce content is from 0.2% to 0.4% （mass fraction）.展开更多
Direct LMD （laser metal deposition） was used to fabricate thin-wall Ti-6Al-4V using the powder mixture of Ti-6 wt.%Al-4 wt.%V. SEM （scanning electron microscopy）, OM （optical microscopy） and EDS （energy dispers...Direct LMD （laser metal deposition） was used to fabricate thin-wall Ti-6Al-4V using the powder mixture of Ti-6 wt.%Al-4 wt.%V. SEM （scanning electron microscopy）, OM （optical microscopy） and EDS （energy dispersive spectroscopy） were employed to examine the chemical composition and microstructure of the as-deposited sections. Vickers hardness tests were then applied to characterize the mechanical properties of the deposit samples which were fabricated using pre-mixed elemental powders. The EDS line scans indicated that the chemical composition of the samples was homogenous across the deposit. After significant analysis, some differences were observed among two sets of deposit samples which varied in the particle size of the mixing Ti-6wt.%Al-4wt.%V powder. It could be found that the set with similar particle number for Ti, Al and V powder made composition much more stable and could easily get industry qualified Ti-6Al-4V components.展开更多
Tribological characteristics and self-repairing effect of hydroxy-magnesium silicate (HMS) dispersed in lubricant oil on steel-to-steel friction pairs with various surface roughness were analyzed.The friction-reductio...Tribological characteristics and self-repairing effect of hydroxy-magnesium silicate (HMS) dispersed in lubricant oil on steel-to-steel friction pairs with various surface roughness were analyzed.The friction-reduction,anti-wear and self-repairing performance of various surface roughness friction pairs were examined by friction testing machine.An operation comparison was made between SJ10W-40 lubricant with and without HMS.The surface morphology and elementary composition of the grinding cracks were analyzed by scanning electron microscope (SEM) and energy dispersive spectrometer (EDS).The results show that the lubrication state changes from boundary lubrication into mixed lubrication after operation in lubricant with HMS.The friction-reduction,anti-wear and self-repairing performance of the friction pairs with various surface roughness are distinctly different.There is a repairing film whose material is different from substrate material on the grinding cracks.In addition,Si,Mg,O,Al and other elements are deposited on the repairing film which contains nanocrystals of these elements.And HMS self-repairing material possesses superior performance of friction-reduction,anti-wear and self-repairing effects.展开更多
Large areas of muddy sediments on the coastal shelves of China provide important samples for studying climate and ecological changes. Analysis of a large number of such samples, which is essential for systematic study...Large areas of muddy sediments on the coastal shelves of China provide important samples for studying climate and ecological changes. Analysis of a large number of such samples, which is essential for systematic study on environmental information recorded in mud areas because of complicated sedimentary environment and variable sedimentary rate, requires a fast and economical method. In this study, we investigated the potential of X-ray fluorescence core scanner （XRFS）, a fast analytical instrument for measuring the elemental concentrations of muddy sediments, and observed a significant correlation between the element concentrations of muddy sediments determined by regular X-ray fluorescence spectrometer （XRF） and XRFS, respectively. The correlations are mainly determined by excitation energy of elements, but also influenced by solubility of element ions. Furthermore, we found a striking link between A1 concentrations and marine-originated organic carbon （MOC）, a proxy of marine primary productivity. This indicates that MOC is partly controlled by sedimentary characteristics. Therefore, XRFS method has a good potential in fast analysis of a large number of muddy sediment samples, and it can also be used to calibrate MOC in ecological study of coastal seas.展开更多
文摘Optical microscopy, and scanning electron microscopy in conjunction with energy dispersed X-ray spectrometry （SEM-EDX）, have been used to study the minerals and the concentrations of 12 trace elements in the No.14 coal from the Huolinhe mine, Inner Mongolia China. The distribution, affinity and removability of the trace elements were studied by float-sink experiments and petrological methods. A high mineral content, dominated by clay minerals, was found in the No.14 coal from the Huolinhe mine. The concentrations of As, Sb and Hg are relatively high compared to the average values for Chinese coals. As, Cr, Hg, Li, Mn, Pb are mainly associated with the minerals while Cd, Co, Ni, Sb, and Se are evenly distributed between the minerals and the organic matter. Be and Ba are mainly distributed in the minerals with a minor proportion in the organic matter. Most elements have a low organic affinity, although Sb, Se, Co, Cd, Ni are closely integrated with the organic matter. High theoretical removabilities are indicated for most trace elements. So it may be possible to lower the concentrations of trace elements during coal preparation.
基金Project(2007CB613702) supported by the National Basic Research Program of ChinaProject(CSTD2006AA4012) supported by the Key Technologies R&D Program of the Chongqing Science and Technology Commission
文摘Mg-1.5Zn-0.2Zr-xCe (x=0, 0.1, 0.3, 0.5, mass fraction, %) alloys were prepared by conventional semi-continuous casting. The effect of rare earth Ce on the microstructure of Mg-1.5Zn-0.2Zr-xCe alloys was studied and the distribution of Ce was analyzed by optical microscopy (OM), X-ray diffractometry (XRD) and scanning electron microscopy (SEM). The results indicate that Ce element exists in the form of Mg12Ce phase and has an obvious refining effect on the microstructure of test alloys. As the Ce content increases, the grain size reduces, the grain boundaries turn thinner, and the distribution of Mg12Ce precipitates becomes more and more dispersed. The Mg-1.5Zn-0.2Zr alloy with 0.3%Ce has the best refinement effect. From center to periphery of the ingot, the amount of granular precipitates in the grain reduces. In longitudinal section of the ingot, some relative long columnar grains appear.
文摘A combination of NAA and micro-PIXE was used to study concentrations and distributions of platinum group elements (PGE) in ores from Xinjie Cu-Pt deposit.The NAA results of the bulk indicate that the ores belong to the enriched Pt-Pd type.The element concentration maps of scanning micro-PIXE for the ores show that the occurence form of Pt is independent arsenide minerals. No PGE were detected in chalcopyrite of Xinjie Cu-Pt deposit. These information are economically beneficial to the mineral smelting process.
文摘We explored the potential use of combining wavelength-dispersive X-ray spectroscopy(WDX) and micromorphology of thin sections to identify minerals in peat soils. Peat soil minerals from three peats and swamps across Golestan Province in northern Iran were first characterized by micromorphological studies. Soils were composed mainly of quartz, muscovite, biotite, pyroxene,sericitized Fe-nodules, and iron-rich garnet. In addition,micromorphological results indicated that Galougah Coastal Swamp sections contained some inorganic residue with biological origin including oyster and limpet, which may be related to the swamp's location near Gorgan Gulf.In order to determine mineralogical properties of samples,twelve unknown grains were chosen for elemental concentration map studies. Quartz, garnet, ilmenite, calcite,and pyroxene in Suteh samples; epidote and Fe-nodule in Ghaleh-Ghafeh Peat Swamp; and barite, phyllosilicates,and calcite in Galougah were identified by WDX mapping of Si, Al, Fe, Ca, Mg, C, Ba, S, and Ti. Composition of the oysters' body was also analyzed by WDX for Si, Ca, Fe,and C. The results indicated that most of the minerals in all sections likely formed through weathering, inheriting their composition from the parent rock. This research suggests that merging micromorphology and SEM/WDX image techniques can be useful in confirming the presence of mineral particles in soil science.
基金Project(2010CB731706) supported by the National Basic Research Program of China
文摘Effect of element cerium （Ce） on microstructure and mechanical properties of A1-Zn-Mg-Cu alloys has been investigated by transmission electron microscopy （TEM）, scanning electron microscopy （SEM）, differential scanning calorimetry （DSC） and hardness test. The results show that addition of Ce can remarkably refine the as-cast grains and eutectic microstructure. A transformation from Mg（Zn,Cu,A1）2 phase to A12CuMg phase is observed during homogenization. Furthermore, the Ce addition introduces changes in the precipitation process and consequently in the age-hardening behavior of the alloy. Microstructural measurements reveal that the addition of Ce promotes the precipitation of η＇ phase, but it also partly retards the precipitation of GP zones. The density of precipitates decreases in a certain degree and rod-like η＇ precipitates increase when Ce content is from 0.2% to 0.4% （mass fraction）.
文摘Direct LMD （laser metal deposition） was used to fabricate thin-wall Ti-6Al-4V using the powder mixture of Ti-6 wt.%Al-4 wt.%V. SEM （scanning electron microscopy）, OM （optical microscopy） and EDS （energy dispersive spectroscopy） were employed to examine the chemical composition and microstructure of the as-deposited sections. Vickers hardness tests were then applied to characterize the mechanical properties of the deposit samples which were fabricated using pre-mixed elemental powders. The EDS line scans indicated that the chemical composition of the samples was homogenous across the deposit. After significant analysis, some differences were observed among two sets of deposit samples which varied in the particle size of the mixing Ti-6wt.%Al-4wt.%V powder. It could be found that the set with similar particle number for Ti, Al and V powder made composition much more stable and could easily get industry qualified Ti-6Al-4V components.
基金Projects(50735006,50904072) supported by the National Natural Science Foundation of ChinaProject(2007CB607601) supported by the National Basic Research Program of China
文摘Tribological characteristics and self-repairing effect of hydroxy-magnesium silicate (HMS) dispersed in lubricant oil on steel-to-steel friction pairs with various surface roughness were analyzed.The friction-reduction,anti-wear and self-repairing performance of various surface roughness friction pairs were examined by friction testing machine.An operation comparison was made between SJ10W-40 lubricant with and without HMS.The surface morphology and elementary composition of the grinding cracks were analyzed by scanning electron microscope (SEM) and energy dispersive spectrometer (EDS).The results show that the lubrication state changes from boundary lubrication into mixed lubrication after operation in lubricant with HMS.The friction-reduction,anti-wear and self-repairing performance of the friction pairs with various surface roughness are distinctly different.There is a repairing film whose material is different from substrate material on the grinding cracks.In addition,Si,Mg,O,Al and other elements are deposited on the repairing film which contains nanocrystals of these elements.And HMS self-repairing material possesses superior performance of friction-reduction,anti-wear and self-repairing effects.
基金supported by the National Basic Research Program of China(2010CB428902)National Natural Science Foundation of China(40876088)
文摘Large areas of muddy sediments on the coastal shelves of China provide important samples for studying climate and ecological changes. Analysis of a large number of such samples, which is essential for systematic study on environmental information recorded in mud areas because of complicated sedimentary environment and variable sedimentary rate, requires a fast and economical method. In this study, we investigated the potential of X-ray fluorescence core scanner （XRFS）, a fast analytical instrument for measuring the elemental concentrations of muddy sediments, and observed a significant correlation between the element concentrations of muddy sediments determined by regular X-ray fluorescence spectrometer （XRF） and XRFS, respectively. The correlations are mainly determined by excitation energy of elements, but also influenced by solubility of element ions. Furthermore, we found a striking link between A1 concentrations and marine-originated organic carbon （MOC）, a proxy of marine primary productivity. This indicates that MOC is partly controlled by sedimentary characteristics. Therefore, XRFS method has a good potential in fast analysis of a large number of muddy sediment samples, and it can also be used to calibrate MOC in ecological study of coastal seas.
