During the process of cross wedge rolling of aluminum alloy hollow shaft, the evolution of its microstructure has an important influence on the mechanical properties of the rolled piece. In order to obtain the microst...During the process of cross wedge rolling of aluminum alloy hollow shaft, the evolution of its microstructure has an important influence on the mechanical properties of the rolled piece. In order to obtain the microstructure evolution law of aluminum alloy hollow shaft in cross wedge rolling without mandrel, a finite element model is constructed through the finite element software Deform-3D. The influences of rolling temperature, sectional shrinkage,spreading angle and forming angle on the average grain size of rolled piece are studied by numerical simulation of microstructure evolution. The cellular automata method reveals the inherent relationship between the process parameters and the evolution of the microstructure, and provides a reference for optimizing the rolling process parameters of aluminum alloy hollow shafts and improving the forming quality. The results show that the average grain size of the rolled piece increases with the increase of the rolling temperature, decreases with the increase of the sectional shrinkage,and decreases first and then increases with the increase of the spreading angle, and changes little with the increase of the forming angle.展开更多
The deformation behavior of V-10Cr-5Ti alloy was studied on the Gleeble-1500 thermomechanical simulator at the temperatures of 950-1350℃, and the strain rates of 0.01-10 s^-1. Based on the Arrhenius model, dislocatio...The deformation behavior of V-10Cr-5Ti alloy was studied on the Gleeble-1500 thermomechanical simulator at the temperatures of 950-1350℃, and the strain rates of 0.01-10 s^-1. Based on the Arrhenius model, dislocation density model, nucleation model and grain growth model, a numerical cellular automaton (CA) model coupling simulation of hot deformation is established to simulate and characterize the microstructural evolution during DRX. The results show that the flow stress is fairly sensitive to the strain rate and deformation temperature. The error between the predicted stress by the Arrhenius model and the actual measured value is less than 8%. The initial average grain size calculated by the CA model is 86.25 μm, which is close to the experimental result (85.63 μm). The simulations show that the effect of initial grain size on the dynamic recrystallization microstructure evolution is not significant, while increasing the strain rate or reducing the temperature can refine the recrystallized grains.展开更多
基金Project(52075272) supported by the National Natural Science Foundation of ChinaProject(LY18E050006) supported by the Natural Science Foundation of Zhejiang Province,China+1 种基金Project(2017A610088) supported by the Natural Science Foundation of Ningbo City,ChinaProjects(2018B10004, 2019B10100) supported by the Ningbo Science and Technology Plan,China。
文摘During the process of cross wedge rolling of aluminum alloy hollow shaft, the evolution of its microstructure has an important influence on the mechanical properties of the rolled piece. In order to obtain the microstructure evolution law of aluminum alloy hollow shaft in cross wedge rolling without mandrel, a finite element model is constructed through the finite element software Deform-3D. The influences of rolling temperature, sectional shrinkage,spreading angle and forming angle on the average grain size of rolled piece are studied by numerical simulation of microstructure evolution. The cellular automata method reveals the inherent relationship between the process parameters and the evolution of the microstructure, and provides a reference for optimizing the rolling process parameters of aluminum alloy hollow shafts and improving the forming quality. The results show that the average grain size of the rolled piece increases with the increase of the rolling temperature, decreases with the increase of the sectional shrinkage,and decreases first and then increases with the increase of the spreading angle, and changes little with the increase of the forming angle.
基金Project(51405110)supported by the National Natural Science Foundation of ChinaProject(20132302120002)supported by the Specialized Research Fund for the Doctoral Program of Higher Education,ChinaProject(LBH-Z14096)supported by Heilongjiang Province Postdoctoral Fund,China
文摘The deformation behavior of V-10Cr-5Ti alloy was studied on the Gleeble-1500 thermomechanical simulator at the temperatures of 950-1350℃, and the strain rates of 0.01-10 s^-1. Based on the Arrhenius model, dislocation density model, nucleation model and grain growth model, a numerical cellular automaton (CA) model coupling simulation of hot deformation is established to simulate and characterize the microstructural evolution during DRX. The results show that the flow stress is fairly sensitive to the strain rate and deformation temperature. The error between the predicted stress by the Arrhenius model and the actual measured value is less than 8%. The initial average grain size calculated by the CA model is 86.25 μm, which is close to the experimental result (85.63 μm). The simulations show that the effect of initial grain size on the dynamic recrystallization microstructure evolution is not significant, while increasing the strain rate or reducing the temperature can refine the recrystallized grains.
