The stability of cemented backfill mass is important to keep miners and equipment safe in underground backfill miming.The stress-strain behavior, resistivity and thermal infrared(TIR) characteristics of backfill mass ...The stability of cemented backfill mass is important to keep miners and equipment safe in underground backfill miming.The stress-strain behavior, resistivity and thermal infrared(TIR) characteristics of backfill mass under uniaxial compression were investigated. The monitoring system consisted of a TIR observation system, a stress-strain monitoring system and a resistivity measurement system. Precursory information for impending failure of cemented backfill mass was collected, including TIR, strain and resistivity precursors. The sensitivity and difference of different monitoring information to the same failure event were compared.The results show that the time-space evolution process of the resistivity and TIR is basically the same as the whole process from compression deformation to failure of backfill mass, and the time variation of resistivity and TIR is obviously characterized by stage.The resistivity precursor turns out earlier than the TIR and the strain. The resistivity relation with loading compression is anti-symmetry, decreasing as the compression stress increases before the peak strength of backfill mass. However, when the backfill mass enters into the phase of failure, the resistivity starts to increase as the stress increases. The change of the resistivity growth direction can be regarded as the resistivity-caution-point for the failure of backfill mass under uniaxial compression. It is also indicated that the TIR information mainly represents the surface temperature evolution in the process of compression before the backfill enters into the plastic-yield state. It can be a valuable tool to obtain the precursors for failure of cemented backfill mass for backfill mines.展开更多
Abstract： A joint solution model of variabk：-mass flow in two-phase region and fluid-solid coupling heat transfer, concerned about the charge process of variable-mass thermodynamic system, is built up and calculated...Abstract： A joint solution model of variabk：-mass flow in two-phase region and fluid-solid coupling heat transfer, concerned about the charge process of variable-mass thermodynamic system, is built up and calculated by the finite element method （FEM）. The results are basically consistent with relative experimental data. The calculated average heat transfer coefficient reaches 1.7~105 W/（m2. K）. When the equal percentage valve is used, the system needs the minimum requirements of valve control, but brings the highest construction cost. With the： decrease of initial steam pressure, the heat transfer intensity also weakens but the steam flow increases. With the initial water filling coefficient increasing or the temperature of steam supply decreasing, the amount of accumulative steam flow increases with the growth of steam pressure. When the pressure of steam supply drops, the steam flow gradient increases during the maximum opening period of control valve, and causes the maximum steam flow to increase.展开更多
基金Projects(51504256,51004109)supported by the National Natural Science Foundation of ChinaProject(zdsys006)supported by State Key Laboratory of Safety and Health for Metal Mines,ChinaProject(2013BAB02B04)supported by the National Science and Technology Support Plan,China
文摘The stability of cemented backfill mass is important to keep miners and equipment safe in underground backfill miming.The stress-strain behavior, resistivity and thermal infrared(TIR) characteristics of backfill mass under uniaxial compression were investigated. The monitoring system consisted of a TIR observation system, a stress-strain monitoring system and a resistivity measurement system. Precursory information for impending failure of cemented backfill mass was collected, including TIR, strain and resistivity precursors. The sensitivity and difference of different monitoring information to the same failure event were compared.The results show that the time-space evolution process of the resistivity and TIR is basically the same as the whole process from compression deformation to failure of backfill mass, and the time variation of resistivity and TIR is obviously characterized by stage.The resistivity precursor turns out earlier than the TIR and the strain. The resistivity relation with loading compression is anti-symmetry, decreasing as the compression stress increases before the peak strength of backfill mass. However, when the backfill mass enters into the phase of failure, the resistivity starts to increase as the stress increases. The change of the resistivity growth direction can be regarded as the resistivity-caution-point for the failure of backfill mass under uniaxial compression. It is also indicated that the TIR information mainly represents the surface temperature evolution in the process of compression before the backfill enters into the plastic-yield state. It can be a valuable tool to obtain the precursors for failure of cemented backfill mass for backfill mines.
基金Project(20080431380) supported by China Postdoctoral Science Foundation
文摘Abstract： A joint solution model of variabk：-mass flow in two-phase region and fluid-solid coupling heat transfer, concerned about the charge process of variable-mass thermodynamic system, is built up and calculated by the finite element method （FEM）. The results are basically consistent with relative experimental data. The calculated average heat transfer coefficient reaches 1.7~105 W/（m2. K）. When the equal percentage valve is used, the system needs the minimum requirements of valve control, but brings the highest construction cost. With the： decrease of initial steam pressure, the heat transfer intensity also weakens but the steam flow increases. With the initial water filling coefficient increasing or the temperature of steam supply decreasing, the amount of accumulative steam flow increases with the growth of steam pressure. When the pressure of steam supply drops, the steam flow gradient increases during the maximum opening period of control valve, and causes the maximum steam flow to increase.
