频域近红外光谱法研究生物组织内部光子传输特性

基于光子在生物组织中的辐射传输理论以及Feng模型,应用频域近红外光谱法研究生物组织中异质体位置的变化,对出射光的光强和相位变化的影响及规律。设计了一仿真实验,用牛奶代替强散射性质的生物组织,并在牛奶中放置一个高度可控的具有一定吸收系数和散射系数的小球。移动小球在牛奶中的高度,检测出射光的交流幅度AC、直流光强DC和相位延迟Phase的值,绘制小球位于不同深度时AC,DC和Phase的曲线,并探讨其变化规律。结果表明,随着小球在牛奶中深度的变化,光强AC,DC和相位Phase呈现一定的相关性;随着光源和检测器之间距离的增加,检测到的光强和相位曲线的波谷点均向右偏移;当小球偏离光源和检测器越远,对检测到的光强和相位的影响越小。验证了光子在生物组织中的传输规律,为用频域近红外光谱法进行组织光学参数的检测及组织中异质体位置的定位奠定了基础。

Sensing characteristics of a metal film coated long-period fiber grating

To obtain the influence rules of the coating parameters of a long-period fiber grating(LPFG)with respect to temperature,strain and refractive index sensing properties,based on the mode coupling theory,a strict four-layer theorietical model of a metal film coated LPFG is established,and these parameters that affect the spectral characteristics of the metal film coated LPFG are studied.The simulation results show that there is an optimal metal film thickness on the surface of the LPFG that will induce the surface-plasmon resonance(SP R)effect,which results in higher sensitivity to the environmental temperature and refractive index but has little influence on the strain There is theoretical evidence that when the silver thickness is between0.8and1.2nm,the refractive index sensitivity will reach the peak point of42.4026,at which the refractive index sensor sensitivity is increased by4.S%.The theoretical results of coating a long-period fiber grating provide a good theoretical basis and guidance for LPFG design and parameters optimization

Induction of Internal Capacitance Effect in Performance Measurement of OPV （Organic Photovoltaic） Device by RTOSM （Real-Time One-Sweep Method）

The advantages of OPV （organic photovoltaic） are low cost, little pollution and flexible. But challenge for OPV manufacture still is lacking of accurately performance measurement due to capacitance issue. Firstly, characterization of OPV requires considering the slowly temporal response due to capacitance effect, and the relative I-V （current-voltage） curves are strongly dependent on the voltage sweep direction, even for the sweep time only in few seconds or less. Secondly, the IPCE （incident photon-to-electron conversion efficiency） also shows the slowly temporal response due to capacitance effect and is dependent on the wavelength of the incident light. Furthermore, the related features for measuring I-V curves are more sensitive with temperature due to non-linear characteristics issue, but current IPCE spectra of OPV are similar to that happened in conventional crystalline Si or amorphous silicon devices. In this work, we developed a RTOSM （real-time one-sweep method） applied both in I-V and IPCE to analysis different electronic transport materials, and result showed this new approach proposed a good way to slow down testing time and having better accuracy for OPV measurement by eliminating acceptance effect instantly.

Tunable slow-light multi-mode photonic crystal waveguides based on the coupling of square cavities

The light transmission properties through two-dimensional photonic crystal waveguides based on coupling of square cavities are studied by the finite-difference time-domain technique.Through interlacing the adjacent cavities along the direction vertical to the waveguide,the coupling distance between the adjacent cavities is extended,and the group velocity of the guiding modes can be slowed by five-fold compared with that in vacuum.Because of the different spatial field distributions of various resonant modes,the corresponding group velocities are also different for the same CROW structure.

Study on transmission characteristics of photonic crystal fiber gratings with periodic air hole deformation

The paper studies a kind of improved photonic crystal fiber gratings fabricated by CO2 laser heating method. The effective refractive index of cladding induced by periodic air hole deformation is computed using multipole method, and the rela-tionship between the effective refractive index and the collapse of air-holes is discussed, thereby the modulation expression of effective refractive index is obtained. The grating transmission characteristics are simulated. The results indicate that with the diameter of air-holes increasing from 3.3 ~m to 3.7 μm, the resonance wavelength shows blue-shift, the resonance peak intensifies, and the bandwidth becomes narrow. As the collapse degree of cladding enhances, the resonance wave- length shows red-shift, the transmission increases, and the bandwidth tends to narrow.

Characteristics of tunable micro-cavity based on one-dimensional photonic crystal doping KTP as defect layer

The tunable micro-cavity based on one-dimensional （ID） photonic crystal doped by KTP is designed. The optical transmission properties in the doped one-dimensional defect photonic crystals are analyzed using transfer matrix method （TMM）. According to the electro-optic effect, the refractive index ellipsoid equation is established with the applied alternating current at both coordinate axes, and the characteristics of temperature-optics and modulation are studied. Numerical calculations and experimental results show that the tuning range is -40 nm.

Light propagation characteristics through the annular coupled-cavity waveguides based on the two-dimensional square-lattice photonic crystal

The light propagation characteristics through the annular coupled-resonator cavity waveguides are systematically analyzed by the finite-difference time-domain (FDTD) method. It is found that this kind of waveguide has more minbands owing to the increasing of the cavity’s size, compared with the traditional line-typed coupled-resonator waveguide. The group velocity of light propagation can be reduced for a further degree when the adjacent annular cavities are interlaced in the perpendicular direction, and a group velocity about 0.00067c (c is the light speed in vacuum) can be obtained.

Study and development of high peak power short pulse Nd:YAG laser for peening applications

Because short pulse Nd:YAG laser of nanosecond pulse-width and high peak power has a unique capability to improve the mechanical properties of metal parts,a study on the development of high peak power short pulse from Nd:YAG laser along with its peening application has been performed.The design scheme of laser and the characteristic of laser beam transmission are presented and discussed.A pulse energy of 25 J with 15 ns pulse-width and a maximum peak power of 1660 k W laser system which use one oscillation and eight amplifiers has been achieved.Laser beam has a max divergence angle of 0.03 mrad,a pulse-to-pulse pulse-width stability of±0.1 ns,and the pulse-to-pulse energy stability factors of less than±2.8%.A low value of divergence means an easier modification of a nearly hat-top laser beam intensity profile and an easier transmission of laser beam.To evaluate the performance of the laser system,several metal materials are processed.Laser peening quality and efficiency are analyzed by using an optical microscope,a transmission electron microscope,and an X-ray diffraction device.The processing results show that the performance of this laser system is excellent.