A numerical model for bilayer organic light-emitting diodes (OLEDs) is developed under the basis of trapped charge limited conduction.The dependences of the current density on the layer thickness,trap properties and c...A numerical model for bilayer organic light-emitting diodes (OLEDs) is developed under the basis of trapped charge limited conduction.The dependences of the current density on the layer thickness,trap properties and carrier mobility of the hole transport layer (HTL) and emission layer (EML) in bilayer OLEDs of the structure anode/HTL/EML/cathode are numerically investigated.It is found that,for given values of the total thickness of organic layers,reduced depth of trap,total density of trap,and carrier mobility of HTL as well as EML,there exists an optimal thickness ratio of HTL to EML,by which a maximal quantum efficiency can be achieved.Through optimization of the thickness ratio,an enhancement of current density and quantum efficiency of as much as two orders of magnitude can be obtained.The dependences of the optimal thickness ratio to the characteristic trap energy,total density of trap and carrier mobility are numerically analyzed.展开更多
In this article, four kinds of optical emission spectroscopic methods of determining electron temperature are used to investigate the relationship between electron temperature and pressure in the cylindrical plasmas o...In this article, four kinds of optical emission spectroscopic methods of determining electron temperature are used to investigate the relationship between electron temperature and pressure in the cylindrical plasmas of dc glow discharges at low pressures in laboratory by measuring the relative intensities of ArI lines at various pressures. These methods are developed respectively on the basis of the Fermi-Dirac model, corona model, and two kinds of electron collision cross section models according to the kinetic analysis. Their theoretical bases and the conditions to which they are applicable are reviewed, and their calculation results and fitting errors are compared with each other. The investigation has indicated that the electron temperatures obtained by the four methods become consistent with each other when the pressure increases in the low pressure argon plasmas.展开更多
To well understand the effect of garment pressure on skin blood flow(SBF) at lower limb,external pressures of various magnitudes were exerted on lower limb in supine or sitting postures respectively using sphygmomanom...To well understand the effect of garment pressure on skin blood flow(SBF) at lower limb,external pressures of various magnitudes were exerted on lower limb in supine or sitting postures respectively using sphygmomanometer.Five male subjects volunteered to participate in this study.An alternating pressure loading protocol between non-pressure and pressure was employed.The SBF was observed by laser flowmeter.No matter the subjects being sitting or supine,SBF obviously increased under low pressure;as the pressure increasing,it turned to decrease.Moreover,while lying supine,SBF turned to decrease under lower pressure than sitting;SBF at calf turned to decrease under lower pressure than at ankle.It was also confirmed that the increment of SBF was obviously higher when the pressure of the same magnitudes was exerted at ankle than at calf.The pressure around 5.32 kPa was confirmed to be a crucial value to SBF.The findings will be helpful in design and application of tight-fit garments.展开更多
Previous works have shown that the suction probe cannot be used to accurately measure the upward and downward particle fluxes independently. A new method using a single optical probe to measure the local solid flux is...Previous works have shown that the suction probe cannot be used to accurately measure the upward and downward particle fluxes independently. A new method using a single optical probe to measure the local solid flux is presented. The measurement of upward, downward and net solid fluxes was carried out in a cold model circulating fluidized bed (CFB) unit. The result shows that the profile of the net solid flux is in good agreement with the previous experimental data measured with a suction probe. The comparison between the average solid flux determined with the optical measuring system and the external solid flux was made, and the maximum deviationturned out to be 22%, with the average error being about 6.9%. These confirm that the optical fiber system can be successfully used to measure the upward, downward and net solid fluxes simultaneously by correctly processing the sampling signals obtained from the optical measuring system.展开更多
A self-developed laser image measurement system was established to study the behavior of bubble for- mation at a single orifice in non-Newtonian polyacrylamide(PAAm)solutions.Images of bubbles were captured by a CCD c...A self-developed laser image measurement system was established to study the behavior of bubble for- mation at a single orifice in non-Newtonian polyacrylamide(PAAm)solutions.Images of bubbles were captured by a CCD camera and volumes of bubbles were digitally analyzed online.The effects of rheological property of PAAm solution,orifice,reservoir,and gas flowrate on bubble formation were studied experimentally.It is found that the volume of bubble increases with the concentration of PAAm solution,the diameter of the orifice,and the gas flowrate,respectively,whereas little effect of reservoir is observed in experiments.展开更多
General multi-protocol label switching(GMPLS) based on traffic engineering is one of the possible methods to implement all-optical network. This method implements the network with IP technique and guarantees the quali...General multi-protocol label switching(GMPLS) based on traffic engineering is one of the possible methods to implement all-optical network. This method implements the network with IP technique and guarantees the quality of service with traffic engineering. Based on the establishment of selecting schemes of optical path and methods of traffic calculation, the wavelength routing algorithm of all-optical network based on traffic engineering is presented by combining with prior route of shortest path and traffic engineering, the algorithm procedures are given, and the actual examples are introduced as well as the analysis on simulation calculation. This research results have certain significance for the achievement of optical switching technique of all-optical network.展开更多
This paper presents a detailed analysis of the complex flow beneath two impinging jets aligned with a low-velocity crossflow which is relevant for the future F-35 VSTOL configuration, and provides a quantitative pictu...This paper presents a detailed analysis of the complex flow beneath two impinging jets aligned with a low-velocity crossflow which is relevant for the future F-35 VSTOL configuration, and provides a quantitative picture of the main features of interest for impingement type of flows. The experiments were carried out for a Reynolds number based on the jet exit conditions of Rej = 4.3 × 10^4, an impingement height of 20.1 jet diameters and for a velocity ratio between the jet exit and the crossflow VR = V/Uo of 22.5. The rear jet is located at S = 6 D downstream of the first jet. The results show a large penetration of the first （upstream）jet that is deflected by the crossflow and impinges on the ground, giving rise to a ground vortex due to the collision of the radial wall and the crossflow that wraps around the impinging point like a scarf. The rear jet （located downstream） it is not so affected by the crossflow in terms of deflection, but due to the downstream wall jet that flows radially from the impinging point of the first jet it does not reach the ground. The results indicate a new flow pattern not yet reported so far, that for a VSTOL aircraft operating in ground vicinity with front wind or small forward movement may result in enhanced under pressures in the aft part of the aircraft causing a suction down force and a change of the pitching moment towards the ground.展开更多
Neutronics measurement system provides neutron fluxes and spectra at the locations of beryllium multiplier and tritium breeder during the operation of the NT-TBM （D-D and D-T phase in ITER）. This is important for st...Neutronics measurement system provides neutron fluxes and spectra at the locations of beryllium multiplier and tritium breeder during the operation of the NT-TBM （D-D and D-T phase in ITER）. This is important for studying and assessing capabilities of beryllium multiplier and tritium breeder in the China helium cooled solid breeder （CNHCSB）. A special neutron diagnostic system has been proposed that allows to measure neutron fluxes and spectra without interrupt the operation of ITER. This system includes encapsulated foil activation analysis, micro-fission chamber detectors （MFC）, and a compact neutron spectrometer using natural diamond detector （NDD）.展开更多
We have measured the deep energy level of the InP: Fe which is semi -insulator through the method of OTCS. The effect of light intensity on OTCS measurement is mainly discussed. There are electron trap of E_T =0.34 eV...We have measured the deep energy level of the InP: Fe which is semi -insulator through the method of OTCS. The effect of light intensity on OTCS measurement is mainly discussed. There are electron trap of E_T =0.34 eV and hole trap of E_T = 1.13 eV in InP: Fe under the strong light and low temperature. The location of the OTCS peak of electron trap (E_T = 0.34 eV) moves towards the direction of high temperaturer, when the light intensity was increased, E_T is different under different light intensity. It is corrected in terms of theory that the stuff ratio of the deep energy level is affected by the light intensity. The experiments show that the error is decreased greatly with the correction.展开更多
To research the influence of oxygen flow rate on the structural and optical properties of TiO2 thin film,TiO2 films on glass were deposited by reactive magnetron sputtering.The microstructure and optical properties we...To research the influence of oxygen flow rate on the structural and optical properties of TiO2 thin film,TiO2 films on glass were deposited by reactive magnetron sputtering.The microstructure and optical properties were measured by X-ray diffractometry,AFM and UV-VIS transmittance spectroscopy,respectively.The results show that the films deposited at oxygen flow rate of 10 mL/min has the lowest roughness and the highest transmittance.The absorption angle shifts to longer wavelengths as oxygen flow rates increase from 5 to 10 mL/min,then to shorter ones as the oxygen flow rate increase from 10 to 30 mL/min.The band gap is 3.38 eV,which is nearly constant in the experiment.For the TiO2 thin films deposited at 10 mL/min of oxyge flow rate,there are nano-crystalline structures,which are suitable for anti-reflection(AR) coating in the solar cells structure system.展开更多
With brief statements of the linear electro-optical modulation and magnetooptical modulation, using the method of resultant of optical amplitude vectors and the methed of Jones matrix, formulas for intensity of transm...With brief statements of the linear electro-optical modulation and magnetooptical modulation, using the method of resultant of optical amplitude vectors and the methed of Jones matrix, formulas for intensity of transmitted light through the optical analyzer of various composition of electro-optical effect with magneto-optical effect are derived. The results show that the output beam from the analyzer carries information on current (or magnetic field), voltage (or electric field), active power and apparent power. When the light beam transmitted through the analyzer are transformed into electric signals, three kinds of information are included: the DC term corresponding to an active power, the term with frequency ω(50 Hz) corresponding to current or voltage, and the term with frequency 2ω(100 Hz) corresponding to an apparnt power.So, we can use the electric filter circuit to pick out the DC component for measuring active power; to pick out the component with frequency ω(50 Hz) for measuring current or voltage; and to pick out the component with frequency 2ω(100 Hz) for measuring apparent power. The paper discusses what quantities are measured when the analyzer is set on certain definite values, and ponts out the optimum selection for various measurements.展开更多
文摘A numerical model for bilayer organic light-emitting diodes (OLEDs) is developed under the basis of trapped charge limited conduction.The dependences of the current density on the layer thickness,trap properties and carrier mobility of the hole transport layer (HTL) and emission layer (EML) in bilayer OLEDs of the structure anode/HTL/EML/cathode are numerically investigated.It is found that,for given values of the total thickness of organic layers,reduced depth of trap,total density of trap,and carrier mobility of HTL as well as EML,there exists an optimal thickness ratio of HTL to EML,by which a maximal quantum efficiency can be achieved.Through optimization of the thickness ratio,an enhancement of current density and quantum efficiency of as much as two orders of magnitude can be obtained.The dependences of the optimal thickness ratio to the characteristic trap energy,total density of trap and carrier mobility are numerically analyzed.
文摘In this article, four kinds of optical emission spectroscopic methods of determining electron temperature are used to investigate the relationship between electron temperature and pressure in the cylindrical plasmas of dc glow discharges at low pressures in laboratory by measuring the relative intensities of ArI lines at various pressures. These methods are developed respectively on the basis of the Fermi-Dirac model, corona model, and two kinds of electron collision cross section models according to the kinetic analysis. Their theoretical bases and the conditions to which they are applicable are reviewed, and their calculation results and fitting errors are compared with each other. The investigation has indicated that the electron temperatures obtained by the four methods become consistent with each other when the pressure increases in the low pressure argon plasmas.
基金Research and Development of High Performance Foundation Wear,ChinaPriority Academic Program Development of Jiangsu Higher Education Institutions(PAPD),China
文摘To well understand the effect of garment pressure on skin blood flow(SBF) at lower limb,external pressures of various magnitudes were exerted on lower limb in supine or sitting postures respectively using sphygmomanometer.Five male subjects volunteered to participate in this study.An alternating pressure loading protocol between non-pressure and pressure was employed.The SBF was observed by laser flowmeter.No matter the subjects being sitting or supine,SBF obviously increased under low pressure;as the pressure increasing,it turned to decrease.Moreover,while lying supine,SBF turned to decrease under lower pressure than sitting;SBF at calf turned to decrease under lower pressure than at ankle.It was also confirmed that the increment of SBF was obviously higher when the pressure of the same magnitudes was exerted at ankle than at calf.The pressure around 5.32 kPa was confirmed to be a crucial value to SBF.The findings will be helpful in design and application of tight-fit garments.
文摘Previous works have shown that the suction probe cannot be used to accurately measure the upward and downward particle fluxes independently. A new method using a single optical probe to measure the local solid flux is presented. The measurement of upward, downward and net solid fluxes was carried out in a cold model circulating fluidized bed (CFB) unit. The result shows that the profile of the net solid flux is in good agreement with the previous experimental data measured with a suction probe. The comparison between the average solid flux determined with the optical measuring system and the external solid flux was made, and the maximum deviationturned out to be 22%, with the average error being about 6.9%. These confirm that the optical fiber system can be successfully used to measure the upward, downward and net solid fluxes simultaneously by correctly processing the sampling signals obtained from the optical measuring system.
基金Supported by the National Natural Science Foundation of China （No.20476073） and the Programs of Introducing Talents of Discipline to Universities （Grant No.B06006）.
文摘A self-developed laser image measurement system was established to study the behavior of bubble for- mation at a single orifice in non-Newtonian polyacrylamide(PAAm)solutions.Images of bubbles were captured by a CCD camera and volumes of bubbles were digitally analyzed online.The effects of rheological property of PAAm solution,orifice,reservoir,and gas flowrate on bubble formation were studied experimentally.It is found that the volume of bubble increases with the concentration of PAAm solution,the diameter of the orifice,and the gas flowrate,respectively,whereas little effect of reservoir is observed in experiments.
基金National Key Lab of Broad Band Fiber Transmission and Communication System Technology , Ministry ofEducation
文摘General multi-protocol label switching(GMPLS) based on traffic engineering is one of the possible methods to implement all-optical network. This method implements the network with IP technique and guarantees the quality of service with traffic engineering. Based on the establishment of selecting schemes of optical path and methods of traffic calculation, the wavelength routing algorithm of all-optical network based on traffic engineering is presented by combining with prior route of shortest path and traffic engineering, the algorithm procedures are given, and the actual examples are introduced as well as the analysis on simulation calculation. This research results have certain significance for the achievement of optical switching technique of all-optical network.
文摘This paper presents a detailed analysis of the complex flow beneath two impinging jets aligned with a low-velocity crossflow which is relevant for the future F-35 VSTOL configuration, and provides a quantitative picture of the main features of interest for impingement type of flows. The experiments were carried out for a Reynolds number based on the jet exit conditions of Rej = 4.3 × 10^4, an impingement height of 20.1 jet diameters and for a velocity ratio between the jet exit and the crossflow VR = V/Uo of 22.5. The rear jet is located at S = 6 D downstream of the first jet. The results show a large penetration of the first （upstream）jet that is deflected by the crossflow and impinges on the ground, giving rise to a ground vortex due to the collision of the radial wall and the crossflow that wraps around the impinging point like a scarf. The rear jet （located downstream） it is not so affected by the crossflow in terms of deflection, but due to the downstream wall jet that flows radially from the impinging point of the first jet it does not reach the ground. The results indicate a new flow pattern not yet reported so far, that for a VSTOL aircraft operating in ground vicinity with front wind or small forward movement may result in enhanced under pressures in the aft part of the aircraft causing a suction down force and a change of the pitching moment towards the ground.
文摘Neutronics measurement system provides neutron fluxes and spectra at the locations of beryllium multiplier and tritium breeder during the operation of the NT-TBM （D-D and D-T phase in ITER）. This is important for studying and assessing capabilities of beryllium multiplier and tritium breeder in the China helium cooled solid breeder （CNHCSB）. A special neutron diagnostic system has been proposed that allows to measure neutron fluxes and spectra without interrupt the operation of ITER. This system includes encapsulated foil activation analysis, micro-fission chamber detectors （MFC）, and a compact neutron spectrometer using natural diamond detector （NDD）.
文摘We have measured the deep energy level of the InP: Fe which is semi -insulator through the method of OTCS. The effect of light intensity on OTCS measurement is mainly discussed. There are electron trap of E_T =0.34 eV and hole trap of E_T = 1.13 eV in InP: Fe under the strong light and low temperature. The location of the OTCS peak of electron trap (E_T = 0.34 eV) moves towards the direction of high temperaturer, when the light intensity was increased, E_T is different under different light intensity. It is corrected in terms of theory that the stuff ratio of the deep energy level is affected by the light intensity. The experiments show that the error is decreased greatly with the correction.
基金Project(08FJ1002) supported by the Hunan Province Key Project of Science and Technology,China
文摘To research the influence of oxygen flow rate on the structural and optical properties of TiO2 thin film,TiO2 films on glass were deposited by reactive magnetron sputtering.The microstructure and optical properties were measured by X-ray diffractometry,AFM and UV-VIS transmittance spectroscopy,respectively.The results show that the films deposited at oxygen flow rate of 10 mL/min has the lowest roughness and the highest transmittance.The absorption angle shifts to longer wavelengths as oxygen flow rates increase from 5 to 10 mL/min,then to shorter ones as the oxygen flow rate increase from 10 to 30 mL/min.The band gap is 3.38 eV,which is nearly constant in the experiment.For the TiO2 thin films deposited at 10 mL/min of oxyge flow rate,there are nano-crystalline structures,which are suitable for anti-reflection(AR) coating in the solar cells structure system.
文摘With brief statements of the linear electro-optical modulation and magnetooptical modulation, using the method of resultant of optical amplitude vectors and the methed of Jones matrix, formulas for intensity of transmitted light through the optical analyzer of various composition of electro-optical effect with magneto-optical effect are derived. The results show that the output beam from the analyzer carries information on current (or magnetic field), voltage (or electric field), active power and apparent power. When the light beam transmitted through the analyzer are transformed into electric signals, three kinds of information are included: the DC term corresponding to an active power, the term with frequency ω(50 Hz) corresponding to current or voltage, and the term with frequency 2ω(100 Hz) corresponding to an apparnt power.So, we can use the electric filter circuit to pick out the DC component for measuring active power; to pick out the component with frequency ω(50 Hz) for measuring current or voltage; and to pick out the component with frequency 2ω(100 Hz) for measuring apparent power. The paper discusses what quantities are measured when the analyzer is set on certain definite values, and ponts out the optimum selection for various measurements.
