A high integrated monolithic IC, with functions of clock recovery, data decision, and 1 ： 4 demultiplexer,is implemented in 0.25μm CMOS process for 2.5Gb/s fiber-optic communications. The recovered and frequency div...A high integrated monolithic IC, with functions of clock recovery, data decision, and 1 ： 4 demultiplexer,is implemented in 0.25μm CMOS process for 2.5Gb/s fiber-optic communications. The recovered and frequency divided 625MHz clock has a phase noise of -106.26dBc/Hz at 100kHz offset in response to a 2.5Gb/s PRBS input data （2^31-1）. The 2.5Gb/s PRBS data are demultiplexed to four 625Mb/s data. The 0.97mm× 0.97mm IC consumes 550mW under a single 3.3V power supply （not including output buffers）.展开更多
O484.5 2001053428光谱法求解极化聚合物薄膜的光电系数=Calcldation of electro-coefficients of poled polymer films using spectral method[刊,中]/孟凡青,马常宝,张光辉,吕孟凯,袁多荣,房昌水,许东(山东大学晶体材料国家重点实验室...O484.5 2001053428光谱法求解极化聚合物薄膜的光电系数=Calcldation of electro-coefficients of poled polymer films using spectral method[刊,中]/孟凡青,马常宝,张光辉,吕孟凯,袁多荣,房昌水,许东(山东大学晶体材料国家重点实验室.山东,济南(250100)),任诠(山东大学光电子信息与工程系。山东,济南(250100))//半导体光电.—2000,21(6).—402-404。展开更多
By calculating the energy distribution of electrons reaching the photocathode surface and solving the Schrodinger equation that describes the behavior of an electron tunneling through the surface potential barrier,we ...By calculating the energy distribution of electrons reaching the photocathode surface and solving the Schrodinger equation that describes the behavior of an electron tunneling through the surface potential barrier,we obtain an equation to calculate the emitted electron energy distribution of transmission-mode NEA GaAs photocathodes. Accord- ing to the equation,we study the effect of cathode surface potential barrier on the electron energy distribution and find a significant effect of the barrier-Ⅰ thickness or end height,especially the thickness,on the quantum efficiency of the cath- ode. Barrier Ⅱ has an effect on the electron energy spread, and an increase in the vacuum level will lead to a narrower electron energy spread while sacrificing a certain amount of cathode quantum efficiency. The equation is also used to fit the measured electron energy distribution curve of the transmission-mode cathode and the parameters of the surface barri- er are obtained from the fitting. The theoretical curve is in good agreement with the experimental curve.展开更多
The electro-optic properties of a poled second-order nonlinear optical maleimide polymer system were reported.This polymer was synthesized by doping disperse red 1 moieties into the maleimide system as the side chains...The electro-optic properties of a poled second-order nonlinear optical maleimide polymer system were reported.This polymer was synthesized by doping disperse red 1 moieties into the maleimide system as the side chains.Its glass transition temperature was measured to be 202 ℃ by Differential Scanning Calorimetry (DSC) technology.After being poled,the measured electro-optic coefficient of PHSD at the wavelength of 1 550 nm is as large as 3.03 pm/v.Except for an initial decay after being poled,PHSD exhibits little electro-optic relaxation in a long term and its electro-optic coefficient remains about 2.46 pm/v after 15 days.展开更多
Purpose： This study was designed to characterize and compare the vertical（kvert） and leg（kleg） stiffness measured during running in two different footwear conditions on negative, level, and positive slopes, using...Purpose： This study was designed to characterize and compare the vertical（kvert） and leg（kleg） stiffness measured during running in two different footwear conditions on negative, level, and positive slopes, using kinematic data only.Methods： Fourteen male recreational runners（age 23.4 4.4 years, height 177.5 5.2 cm, and body mass 69.5 5.3 kg） were tested on 2separate days within 1 week. At each session, subjects ran seven 5-min trials on a treadmill at 10 km/h, interspersed with 5 min of sitting passive recovery. Each trial was performed on a different slope gradient, ranging from 8%（downhill） to t8%（uphill）, assigned in a random order.Furthermore, each subject ran one 5-min trial wearing minimal shoes（MS） and the subsequent trial wearing traditional shoes（TS） in a counterbalanced randomized order ensuring that each slope was ran once in MS and once in TS. Kinematic data were collected using a photocell measuring system and high-speed video camera, with kvertand klegstiffness being calculated from these data.Results： Leg compression, contact times, and vertical displacement of the center of mass during running were significantly smaller in MS compared to TS across all slopes. In the two footwear conditions, step frequency significantly increased with a（positive） increase in slope.Kinematic analyses indicated that klegwas greater when running in MS than TS and this between-footwear difference remained similar across slopes. On the contrary, kvertdid not change on the basis of footwear, but increased with positive increases in slope.Conclusion： This study showed that kvertand klegduring running respond differently to change in footwear and/or slope. These two stiffness measures can hence provide a unique insight on the biomechanical adaptations of running under varying conditions and their respective quantification may assist in furthering our understanding of training, performance, and/or injury in this sport.展开更多
A CO2 laser die-cutting system, which does not need die board any more, is a new technique for manufac-turing packing box. Two optical paths, the galvanometer scanning system and the flying optical system, are used to...A CO2 laser die-cutting system, which does not need die board any more, is a new technique for manufac-turing packing box. Two optical paths, the galvanometer scanning system and the flying optical system, are used to satisfy different processing needs. The scanning system is composed of galvanometer scanning mirrors and F-θ lens. And the flying optical system is driven by two servo motors. This paper presents the software and hardware design of the laser die-cutting system, the difference between the two optical paths, as well as the relationship among the cutting speed, thickness of wrapping paper and laser power. The cutting speed and thickness of wrapping paper are linearly increased by the incremental laser power, while the cutting speed is hyperbolically decreased by the incremental thickness of wrapping paper when the laser power is constant. The amount of incision is reduced by 20% and the processing time by 40% when tested by a low power RF CO2 laser die-cutting system using the optimized program. This tech- nique is also used for the reference of other rapid laser processing systems.展开更多
In PV （photovoltaic） power systems, a MPPT （maximum power point tracking） algorithm is vital in increasing their efficiency. But it is also vital to take into account the non ideal conditions resulting from comple...In PV （photovoltaic） power systems, a MPPT （maximum power point tracking） algorithm is vital in increasing their efficiency. But it is also vital to take into account the non ideal conditions resulting from complex physical environments in such PV power systems. To minimize the degradation of performances caused by these conditions, and therefore adding reliability and robustness, this paper presents an implementation of a digitally controlled system using a topology based on series connected DC-DC buck converters for a stand-alone PV power system applications, operating with local and autonomous controls, to track the maximum power points of PV modules in non ideal conditions. Simulations are carried out by using C-MEX S-functions under MATLAB-SIMULINK environment. A PV system of 1.44 kWc is described and simulation results are presented.展开更多
The beam deflectors based on electro-optic phased array（EOPA） is mainly described, and then an analysis on existing control schemes for driving the EOPA beam deflectors, based on custom hard-wired electronics or bas...The beam deflectors based on electro-optic phased array（EOPA） is mainly described, and then an analysis on existing control schemes for driving the EOPA beam deflectors, based on custom hard-wired electronics or based on software in a microcontroUer, is made. Compared with these, a driving and control system for a multi-channel EOPA beam deflector is presented, in which the control assignment is implemented with a field programmable gate array（FPGA） chip. For different performance requirements, two control schemes, one with the serial scheme and another with the parallel scheme, have been explored and rapidly prototyped in Xilinx FPGA chips. With the control structures for the EOPA beam deflector, scanning rates of 588 kHz and 5 MHz can be respectivelv reached.展开更多
The comparative analysis of modem mathematical models for 3D problems in electron optics is presented. The new approach to solve the electron optics problems in three dimensions is presented. It is based on the princi...The comparative analysis of modem mathematical models for 3D problems in electron optics is presented. The new approach to solve the electron optics problems in three dimensions is presented. It is based on the principal ray method suggested by G. Grinberg in 1948. That perspective approach was not realized before for full three-dimensional electron optic systems, probably because of the complexity of its mathematical apparatus. We describe the analytical technique of the BEM （boundary element method） for the field evaluation, and 3rd order aberration expansion for the trajectory analysis. The first version of such computer code ＂OPTICS-3＂ and some results of numerical simulations with this code were presented.展开更多
This work proposes a 12 kW three-phase grid-connected single stage PWM DC-AC converter destined to process the energy provided by a photovoltaic array composed of 57 KC200GT PV modules with high power factor for any s...This work proposes a 12 kW three-phase grid-connected single stage PWM DC-AC converter destined to process the energy provided by a photovoltaic array composed of 57 KC200GT PV modules with high power factor for any solar radiation. The PWM inverter modeling and the control strategy, using dqO transformation, are proposed in order to also allow the system operation as an active power filter, capable to compensate harmonic components and react power generated by the non-linear loads connected to the mains grid. An input voltage clamping technique is proposed to impose the photovoltaic operation on the maximum power point. Simulation and experimental results are presented to validate the proposed methodology for grid connected photovoltaic generation system.展开更多
In this paper, the performance of a concentrating photovoltaic/thermal solar system is numerically analyzed with a mathematical and physical model. The variations of the electrical efficiency and the thermal efficienc...In this paper, the performance of a concentrating photovoltaic/thermal solar system is numerically analyzed with a mathematical and physical model. The variations of the electrical efficiency and the thermal efficiency with the operation parameters are calculated. It is found that the electrical efficiency increases at first and then decreases with increasing concentration ratio of the sunlight, while the thermal efficiency acts in an opposite manner. When the velocity of the cooling water increases, the electrical efficiency increases. Considering the solar system, the surface of the sun, the atmosphere and the environment, we can get a coupled energy system, which is analyzed with the entropy generation minimization and the entransy theory. This is the first time that the entransy theory is used to analyze photovoltaic/thermal solar system. When the concentration ratio is fixed, it is found that both the minimum entropy generation rate and the maximum entransy loss rate lead to the maximum electrical output power,while both the minimum entropy generation numbers and the maximum entransy loss coefficient lead to the maximum electrical efficiency. When the concentrated sunlight is not fixed, it is shown that neither smaller entropy generation rate nor larger entransy loss rate corresponds to larger electrical output power. Smaller entropy generation numbers do not result in larger electrical efficiency, either. However, larger entransy loss coefficient still corresponds to larger electrical efficiency.展开更多
文摘A high integrated monolithic IC, with functions of clock recovery, data decision, and 1 ： 4 demultiplexer,is implemented in 0.25μm CMOS process for 2.5Gb/s fiber-optic communications. The recovered and frequency divided 625MHz clock has a phase noise of -106.26dBc/Hz at 100kHz offset in response to a 2.5Gb/s PRBS input data （2^31-1）. The 2.5Gb/s PRBS data are demultiplexed to four 625Mb/s data. The 0.97mm× 0.97mm IC consumes 550mW under a single 3.3V power supply （not including output buffers）.
文摘O484.5 2001053428光谱法求解极化聚合物薄膜的光电系数=Calcldation of electro-coefficients of poled polymer films using spectral method[刊,中]/孟凡青,马常宝,张光辉,吕孟凯,袁多荣,房昌水,许东(山东大学晶体材料国家重点实验室.山东,济南(250100)),任诠(山东大学光电子信息与工程系。山东,济南(250100))//半导体光电.—2000,21(6).—402-404。
文摘By calculating the energy distribution of electrons reaching the photocathode surface and solving the Schrodinger equation that describes the behavior of an electron tunneling through the surface potential barrier,we obtain an equation to calculate the emitted electron energy distribution of transmission-mode NEA GaAs photocathodes. Accord- ing to the equation,we study the effect of cathode surface potential barrier on the electron energy distribution and find a significant effect of the barrier-Ⅰ thickness or end height,especially the thickness,on the quantum efficiency of the cath- ode. Barrier Ⅱ has an effect on the electron energy spread, and an increase in the vacuum level will lead to a narrower electron energy spread while sacrificing a certain amount of cathode quantum efficiency. The equation is also used to fit the measured electron energy distribution curve of the transmission-mode cathode and the parameters of the surface barri- er are obtained from the fitting. The theoretical curve is in good agreement with the experimental curve.
基金This work is partially supported by National Natural ScienceFoundation of China ( Grant No:60377013 ,60507013) WHUT Foundation(XJJ2005175) .
文摘The electro-optic properties of a poled second-order nonlinear optical maleimide polymer system were reported.This polymer was synthesized by doping disperse red 1 moieties into the maleimide system as the side chains.Its glass transition temperature was measured to be 202 ℃ by Differential Scanning Calorimetry (DSC) technology.After being poled,the measured electro-optic coefficient of PHSD at the wavelength of 1 550 nm is as large as 3.03 pm/v.Except for an initial decay after being poled,PHSD exhibits little electro-optic relaxation in a long term and its electro-optic coefficient remains about 2.46 pm/v after 15 days.
基金supported by the University of Franche Comte' (France) and the Exercise, Performance, Health, and Innovation platform of Besancon
文摘Purpose： This study was designed to characterize and compare the vertical（kvert） and leg（kleg） stiffness measured during running in two different footwear conditions on negative, level, and positive slopes, using kinematic data only.Methods： Fourteen male recreational runners（age 23.4 4.4 years, height 177.5 5.2 cm, and body mass 69.5 5.3 kg） were tested on 2separate days within 1 week. At each session, subjects ran seven 5-min trials on a treadmill at 10 km/h, interspersed with 5 min of sitting passive recovery. Each trial was performed on a different slope gradient, ranging from 8%（downhill） to t8%（uphill）, assigned in a random order.Furthermore, each subject ran one 5-min trial wearing minimal shoes（MS） and the subsequent trial wearing traditional shoes（TS） in a counterbalanced randomized order ensuring that each slope was ran once in MS and once in TS. Kinematic data were collected using a photocell measuring system and high-speed video camera, with kvertand klegstiffness being calculated from these data.Results： Leg compression, contact times, and vertical displacement of the center of mass during running were significantly smaller in MS compared to TS across all slopes. In the two footwear conditions, step frequency significantly increased with a（positive） increase in slope.Kinematic analyses indicated that klegwas greater when running in MS than TS and this between-footwear difference remained similar across slopes. On the contrary, kvertdid not change on the basis of footwear, but increased with positive increases in slope.Conclusion： This study showed that kvertand klegduring running respond differently to change in footwear and/or slope. These two stiffness measures can hence provide a unique insight on the biomechanical adaptations of running under varying conditions and their respective quantification may assist in furthering our understanding of training, performance, and/or injury in this sport.
基金Supported by by Major State Basic Research Development Program of China ("973" Program, No. 2010CB327800)
文摘A CO2 laser die-cutting system, which does not need die board any more, is a new technique for manufac-turing packing box. Two optical paths, the galvanometer scanning system and the flying optical system, are used to satisfy different processing needs. The scanning system is composed of galvanometer scanning mirrors and F-θ lens. And the flying optical system is driven by two servo motors. This paper presents the software and hardware design of the laser die-cutting system, the difference between the two optical paths, as well as the relationship among the cutting speed, thickness of wrapping paper and laser power. The cutting speed and thickness of wrapping paper are linearly increased by the incremental laser power, while the cutting speed is hyperbolically decreased by the incremental thickness of wrapping paper when the laser power is constant. The amount of incision is reduced by 20% and the processing time by 40% when tested by a low power RF CO2 laser die-cutting system using the optimized program. This tech- nique is also used for the reference of other rapid laser processing systems.
文摘In PV （photovoltaic） power systems, a MPPT （maximum power point tracking） algorithm is vital in increasing their efficiency. But it is also vital to take into account the non ideal conditions resulting from complex physical environments in such PV power systems. To minimize the degradation of performances caused by these conditions, and therefore adding reliability and robustness, this paper presents an implementation of a digitally controlled system using a topology based on series connected DC-DC buck converters for a stand-alone PV power system applications, operating with local and autonomous controls, to track the maximum power points of PV modules in non ideal conditions. Simulations are carried out by using C-MEX S-functions under MATLAB-SIMULINK environment. A PV system of 1.44 kWc is described and simulation results are presented.
基金National Natural Science Foundation of China(60477042)
文摘The beam deflectors based on electro-optic phased array（EOPA） is mainly described, and then an analysis on existing control schemes for driving the EOPA beam deflectors, based on custom hard-wired electronics or based on software in a microcontroUer, is made. Compared with these, a driving and control system for a multi-channel EOPA beam deflector is presented, in which the control assignment is implemented with a field programmable gate array（FPGA） chip. For different performance requirements, two control schemes, one with the serial scheme and another with the parallel scheme, have been explored and rapidly prototyped in Xilinx FPGA chips. With the control structures for the EOPA beam deflector, scanning rates of 588 kHz and 5 MHz can be respectivelv reached.
文摘The comparative analysis of modem mathematical models for 3D problems in electron optics is presented. The new approach to solve the electron optics problems in three dimensions is presented. It is based on the principal ray method suggested by G. Grinberg in 1948. That perspective approach was not realized before for full three-dimensional electron optic systems, probably because of the complexity of its mathematical apparatus. We describe the analytical technique of the BEM （boundary element method） for the field evaluation, and 3rd order aberration expansion for the trajectory analysis. The first version of such computer code ＂OPTICS-3＂ and some results of numerical simulations with this code were presented.
文摘This work proposes a 12 kW three-phase grid-connected single stage PWM DC-AC converter destined to process the energy provided by a photovoltaic array composed of 57 KC200GT PV modules with high power factor for any solar radiation. The PWM inverter modeling and the control strategy, using dqO transformation, are proposed in order to also allow the system operation as an active power filter, capable to compensate harmonic components and react power generated by the non-linear loads connected to the mains grid. An input voltage clamping technique is proposed to impose the photovoltaic operation on the maximum power point. Simulation and experimental results are presented to validate the proposed methodology for grid connected photovoltaic generation system.
基金supported by the National Natural Science Foundation of China(Grant No.51376101)the Science Fund for Creative Research Groups(Grant No.51621062)
文摘In this paper, the performance of a concentrating photovoltaic/thermal solar system is numerically analyzed with a mathematical and physical model. The variations of the electrical efficiency and the thermal efficiency with the operation parameters are calculated. It is found that the electrical efficiency increases at first and then decreases with increasing concentration ratio of the sunlight, while the thermal efficiency acts in an opposite manner. When the velocity of the cooling water increases, the electrical efficiency increases. Considering the solar system, the surface of the sun, the atmosphere and the environment, we can get a coupled energy system, which is analyzed with the entropy generation minimization and the entransy theory. This is the first time that the entransy theory is used to analyze photovoltaic/thermal solar system. When the concentration ratio is fixed, it is found that both the minimum entropy generation rate and the maximum entransy loss rate lead to the maximum electrical output power,while both the minimum entropy generation numbers and the maximum entransy loss coefficient lead to the maximum electrical efficiency. When the concentrated sunlight is not fixed, it is shown that neither smaller entropy generation rate nor larger entransy loss rate corresponds to larger electrical output power. Smaller entropy generation numbers do not result in larger electrical efficiency, either. However, larger entransy loss coefficient still corresponds to larger electrical efficiency.
