郭忠恕《雪霁江行图》与赵光辅人物画风

我们通常想当然地认为五代和北宋的画作只有一位作者,此次演讲将探讨一个例外——即郭忠恕《雪霁江行图》中的人物。据史料记载,郭忠恕并不喜画人物并曾将自己画中的人物留给另一位年轻画家王士元来作。那么,《雪霁江行图》中的人物究竟是出自谁手呢?是郭忠恕,还是王士元,亦或是另一位画家呢?此画中的人物风格独特。通过将这些人物与其他具有鲜明开封风格的画作中的人物进行对比。

三维动画中场景主辅灯光亮度比值的探讨

三维动画中使用三点照明法很便捷和实用,其中对于照射物体的主光和辅助光之间比值的不同,达到的效果也不同。掌握好其中的主光与辅助光比值的规律,可以帮助创造者更快捷的实现所需塑造效果。

激光+高频电美容治疗500例体表肿瘤

本文总结了我科自1987年——1992年底应用CO2激光辅以高频电刀,手术缝合法治疗颜面部体表良恶性肿瘤500例的体会。

虚拟布光法

文章论述了虚拟布光法的概念、特点及应用情况。

3DS MAX基础灯光策略探析

分析了三维场景中布光的基本原则,在实践的基础上提出针对复杂场景设置多个灯光要注意场景的明暗层次,充分利用3ds m ax中灯光的衰减属性、“排除”与“包括”功能,学会利用阴影贴图等,这将极大的增强场景中灯光的真实性,同时为三维场景的灯光布置提供合理依据。

演播室的常用布光法

文章论述了常用几种布光法的概念、特点及应用情况。

Interface characteristics of Al_2O_3－13%TiO_2 ceramic coatings prepared by laser cladding

Al2O3-13%TiO2 （mass fraction） coatings, prepared by laser cladding on nickel-based alloy, were heated using high frequency induction sources. The coating microstructure and the interface between bond coating and ceramic coating were characterized by SEM, XRD and EDS. The results show that two-layer substructure exists in the ceramic coating： one layer evolving from fully melted region where the sintered grains grow fully; another layer resembling the liquid-phase-sintered structure consisting of three-dimensional net where the melted Al2O3 particles are embedded in the TiO2-rich matrix. The mechanism of the two-layer substructure formation is also explained in terms of the melting and flattening behavior of the powders during laser cladding processing. The spinel compounds NiAl2O4 and acicular compounds Cr2O3 are discovered in the interface between bond coating and ceramic coating. It proves that the chemical reactions in the laser cladding process will significantly enhance the coating adhesion.

Purification and Characterization of Flammulin,a Basic Protein with Anti-tumor Activities from Flammulina velutipes

Aim To purify and characterize flammulin, a basic protein with anti-tumoractivities. Methods Ammonium sulfate, ethanol fractionation and column chromatography were used forseparation and purification. Electrophoretic analysis, amino acid analysis, and MS of flammulin werecarried out. Results Flammulin was purified to electrophoretic homogeneity and crystallized. With amolecular mass of 19891.13 Da, pI 8.9, λ_(max) = 276 - 278 nm, λ_(min) = 250 nm, flammulin wascharacterized by its lack of methionine. Fingerprint mapping of flammulin was determined by MALDI-MSfollowing in-gel protease digestion; no close matches were identified. Conclusion Flammulin waspurified to electrophoretic homogeneity, and its characteristics are discussed for the first time.

Influence Factors on Particle Growth for On-line Aerosol Matrix-assisted Laser Desorption/Ionization Time-of-flight Mass Spectrometry

An evaporation/condensation flow cell was developed and interfaced with the matrix-assisted laser desorption/ionization （MALDI） time-of-flight mass spectrometer for on-line bioaerosol detection and characterization, which allows matrix addition by condensation onto the laboratory-generated bioaerosol particles. The final coated particle exiting from the con- denser is then introduced into the aerodynamic particle sizer spectrometer or home-built aerosol laser time-of-flight mass spectrometer, and its aerodynamic size directly effects on the matrix-to-analyte molar ratio, which is very important for MALDI technique. In order to observe the protonated analyte molecular ion, and then determine the classification of bi- ological aerosols, the matrix-to-analyte molar ratio must be appropriate. Four experimental parameters, including the temperature of the heated reservoir, the initial particle size, its number concentration, and the matrix material, were tested experimentally to analyze their influences on the final particle size. This technique represents an on-line system of detection that has the potential to provide rapid and reliable identification of airborne biological aerosols.

Detection of Terahertz Photon by GaAs-Based Single Electron Transistor at Low Temperatures

A reproducible terahertz （THz） photocurrent was observed at low temperatures in a Schottky wrap gate single electron transistor with a normal-incident of a CH3OH gas laser with the frequency 2.54THz. The change of source-drain current induced by THz photons shows that a satellite peak is generated beside the resonance peak. THz photon energy can be characterized by the difference of gate voltage positions between the resonance peak and satellite peak. This indicates that the satellite peak exactly results from the THz photon-assisted tunneling. Both experimental results and theoretical analysis show that a narrow spacing of double barriers is more effective for the enhancement of THz response.

Plant Proteomics in the Post-genomic Era

Proteomics is one of the most active research fields in the post-genomic era. Here we briefly introduce the scientific background of the origination of proteomics and its content, research method. The new developments of proteomics at the levels of individual plants, tissues, organs and organells, as well as its applications in the area of plant genetic diversity, mutant characterization, and plant physiology, etc are reviewed. At last, the challenge and prospect of proteomics are discussed.

A RECURSIVE GENERATIVE APPROACH IN OPTICAL PRISM CAPP

In this paper, the generative approach utilizes recursion to generate process sequence for a part, and then match detail procedure design and select process equipment. A set of recursive formulas are found. Finally a complete process program is produced. The method is simple than that of the knowledge system, the artificial neural networks and variant approach computer aided process planning(VACAPP).

Photolithography Process Simulation for Integrated Circuits and Microelectromechanical System Fabrication

Simulations of photoresist etching,aerial image,exposure,and post-bake processes are integrated to obtain a photolithography process simulation for microelectromechanical system（MEMS） and integrated circuit（IC） fabrication based on three-dimensional （3D） cellular automata（CA）. The simulation results agree well with available experimental results. This indicates that the 3D dynamic CA model for the photoresist etching simulation and the 3D CA model for the post-bake simulation could be useful for the monolithic simulation of various lithography processes. This is determined to be useful for the device-sized fabrication process simulation of IC and MEMS.

A review of light amplification by stimulated emission of radiation in oil and gas well drilling

The prospect of employing Light Amplification by Stimulated Emission of Radiation(LASER) for well drilling in oil and gas industry was examined.In this work,the experimental works carried out on various oil well drilling operations was discussed.The results show that,LASER or LASER-aided oil and gas well drilling has many potential advantages over conventional rotary drilling,including high penetration rate,reduction or elimination of tripping,casing,bit costs,enhanced well control,as well as perforating and side-tracking capabilities.The investigation also reveals that modern infrared LASERs have a higher rate of rock cuttings removal than that of conventional rotary drilling and flame-jet spallation.It also reveals that LASER can destroy rock without damaging formation permeability but rather,it enhances or improves permeability and that permeability and porosity increases in all rock types.The paper has therefore provided more knowledge on the potential value to drilling operations and techniques using LASER.

Prediction of preheating conditions for inclined laser assisted machining

For laser assisted machining,shape of preheating laser heat source is changed irregularly because of complexity of material shape.So,the preheating temperature should be controlled by adjusting the feed rate or the laser power.Thermal analyses of the laser assisted machining process for inclination planes were performed.By analyzing the obtained temperature profile,a proper feed rate control method was proposed according to the inclination angles.In addition,the temperature distribution of the cross section after feed rate control was predicted.The correlation equation between inclination angles and adjusted proper feed rate was proposed.The results of this analysis can be used to predict the preheating effect on workpiece and can be applied as a preheating temperature control method in laser assisted machining processes.

Estimation of deformed laser heat sources and thermal analysis on laser assisted turning of square member

Laser assisted machining （LAM） has difficulties in estimating temperature after applying a LAM process due to its very small heat input area, large energy and movement. In particular, in the case of laser assisted turning （LAT） process, it is more difficult to estimate the temperature after preheating because it has a shape of ellipse when a laser heat source is rotated. A prediction method and thermal analysis method for heat source shapes were proposed as a square shaped member was preheated. The temperature distribution was calculated according to the rotation of the member. Compared with the results of the former study, the maximum temperature of the calculation results, 1 407.1 ℃, is 8.5 ℃ higher than that of the square member, which is 1 398.6 ℃. In a LAT process for a square member, the maximum temperature is 1 850.8 ℃. It is recognized that a laser power control process is required because square members show a maximum temperature that exceeds a melting temperature at around a vertex of the member according to the rotation.

NC code generation for laser assisted turn-mill of various type of clovers and square section members

Laser assisted turning （LAT） is one of the advanced machining technologies, which uses laser power to heat the surface of a workpiece before the material is removed. It has several advantages of low manufacturing costs, high productivity and high qualities to machine difficult-to-cut materials such as silicon nitride, muUite, zirconia and Ni. A large part of studies on LAT have been focused on a round bar. With increasing demands for high quality products and high performance engineering system, the researches on LAT for clover and square section members are necessary. But, these workpieces are impossible to be machined on conventional CNC lathe and to generate NC code with current CAM softwares. As a basic research for combining LAT with a tilting index table type 5-axis machining center, i.e. laser assisted turn-mill, a new method is suggested to generate NC code that can process various types of clover and square section members through development of C＋＋ program.

Eigenstates of Laser-Assisted Scattering in a Noninertial Frame

In a rotating noninertial frame, we investigate the eigenstates of the time-dependent problem for electronnucleus scattering assisted by a circularly polarized laser field. Numerical results of probability distribution, quantum potential, and current density are discussed. An approximate expression of scattering cross section for low laser frequency is given.

Residual stress and welding distortion of Al/steel butt joint by arc-assisted laser welding-brazing

The thermo-elastic.plastic finite element method(FEM)is used to simulate the thermo-mechanical behavior of Al/steel tungsten inert gas(TIG)arc-assisted laser welding-brazing(A-LWB)butt joint.The influence of material nonlinearity,geometrical nonlinearity and work hardening on the welding process is studied,and the differences in the welding temperature field,residual stress and welding distortion by A-LWB and by single laser welding-brazing(SLWB)are analyzed.The results show that the thermal cycle,residual stress distribution and welding distortion by the numerical simulation are in good agreement with the measured data by experiments,which verifies the effectiveness of FEM.Compared with the SLWB,A-LWB can make the high-temperature distribution zone of weld in width direction wider,decrease the transverse tensile stress in the weld and reduce the distribution range of longitudinal tensile stress.And the welding deformation also decreases to some extent.