A series of non-woven fabrics were fabricated by blending S0- 80wt% of thennoregulated fibres containing n-elcosane, n-nonadecane or n-octadecane with 0 - 40wt% PET fibres and 0- 20wt% PP fibres. The phase change prop...A series of non-woven fabrics were fabricated by blending S0- 80wt% of thennoregulated fibres containing n-elcosane, n-nonadecane or n-octadecane with 0 - 40wt% PET fibres and 0- 20wt% PP fibres. The phase change properties, thermal conductivity, thermal resistance, heat flux and inner temperature difference between wool felt and the thermoregulated non-woven fabrics of the non-woven fabrics were measured respectively. The thereto-regulated non-woven fabrics absorb heat at 25- 34℃ and release heat at 10- 25℃. The measured highest enthalpy of the non-woven is approximately 18J/g. During a heating process, heat flux of the non-woven fabrics is composed of three parts, heat absorbed by the cold textile touching the hot plate, heat transmitted from the hot plate to the cold plate, and the heat absorbed by PCM from the hot plate during the phase change process. The measured maximum inner temperature difference in a temperature rising process between the wool felt and the thermo-regulated non-woven fabric is approximately 8℃. The inner temperature difference （Tr-Ts〉0） lasts 16 - 45 min By contrary, the measured maximum inner temperature difference in the temperature decreasing process is approximately - 6. 5℃. The inner temperature difference （Tr-Ts〈0） lasts 16 - 50 min, The temperature regulation properties are obviously observed.展开更多
The quantity of installed PV （photovoltaic） systems in the German distribution grid is still increasing. In some areas, the installed PV capacity exceeds 5 kW per HC （house connection）. Therefore, the load flow ch...The quantity of installed PV （photovoltaic） systems in the German distribution grid is still increasing. In some areas, the installed PV capacity exceeds 5 kW per HC （house connection）. Therefore, the load flow changes its characteristics and leads to new requirements for the grid. In some areas, the power feedback is higher than the delivery and the installed PV capacity becomes the decisive factor for grid planning. This paper discusses the impact of PV systems on the flicker level. The focus hereby is on the correlation among the flicker level, the grid voltage and the meteorological parameters. Different approaches to investigate if there is an influence of PV systems on the maximum flicker are taken into account. Furthermore, an investigation if the normative limit is exceeded will be shown.展开更多
基金the financial supports from The Hong Kong Polytechnic University(the Area of Strategic Development Project,No A180) the National Natural Science Foundation of China(No50073015).
文摘A series of non-woven fabrics were fabricated by blending S0- 80wt% of thennoregulated fibres containing n-elcosane, n-nonadecane or n-octadecane with 0 - 40wt% PET fibres and 0- 20wt% PP fibres. The phase change properties, thermal conductivity, thermal resistance, heat flux and inner temperature difference between wool felt and the thermoregulated non-woven fabrics of the non-woven fabrics were measured respectively. The thereto-regulated non-woven fabrics absorb heat at 25- 34℃ and release heat at 10- 25℃. The measured highest enthalpy of the non-woven is approximately 18J/g. During a heating process, heat flux of the non-woven fabrics is composed of three parts, heat absorbed by the cold textile touching the hot plate, heat transmitted from the hot plate to the cold plate, and the heat absorbed by PCM from the hot plate during the phase change process. The measured maximum inner temperature difference in a temperature rising process between the wool felt and the thermo-regulated non-woven fabric is approximately 8℃. The inner temperature difference （Tr-Ts〉0） lasts 16 - 45 min By contrary, the measured maximum inner temperature difference in the temperature decreasing process is approximately - 6. 5℃. The inner temperature difference （Tr-Ts〈0） lasts 16 - 50 min, The temperature regulation properties are obviously observed.
文摘The quantity of installed PV （photovoltaic） systems in the German distribution grid is still increasing. In some areas, the installed PV capacity exceeds 5 kW per HC （house connection）. Therefore, the load flow changes its characteristics and leads to new requirements for the grid. In some areas, the power feedback is higher than the delivery and the installed PV capacity becomes the decisive factor for grid planning. This paper discusses the impact of PV systems on the flicker level. The focus hereby is on the correlation among the flicker level, the grid voltage and the meteorological parameters. Different approaches to investigate if there is an influence of PV systems on the maximum flicker are taken into account. Furthermore, an investigation if the normative limit is exceeded will be shown.
