目的观察一种新型血液透析技术—内源性再输注血液透析滤过(hemodiafiltration with endogenous reinfusion,HFR)对缓解血液透析患者瘙痒症状的效果。方法行前后对照研究,比较患者HFR治疗前、后瘙痒症状、睡眠质量、生活质量和相关实验...目的观察一种新型血液透析技术—内源性再输注血液透析滤过(hemodiafiltration with endogenous reinfusion,HFR)对缓解血液透析患者瘙痒症状的效果。方法行前后对照研究,比较患者HFR治疗前、后瘙痒症状、睡眠质量、生活质量和相关实验室检查指标。结果HFR治疗前、后瘙痒严重程度(Z=-2.023,P=0.043)、睡眠质量(t=7.318,P<0.001)和生活质量(t=4.804,P=0.003)差异均有统计学意义。结论HFR治疗在一定程度上可减轻尿毒症患者的瘙痒症状,改善其睡眠质量和生活质量。展开更多
2026 aluminum alloy was compressed in a temperature range of 300-450 ℃ and strain rate range of 0.01-10 s^-1. The correlation between compression conditions and microstructural evolution after solution and aging heat...2026 aluminum alloy was compressed in a temperature range of 300-450 ℃ and strain rate range of 0.01-10 s^-1. The correlation between compression conditions and microstructural evolution after solution and aging heat treatment was investigated. It is found that the recrystallization and precipitation behavior after heat treatment are associated with the temperature compensated strain rate Z value during hot deformation. Under low Z parameter condition, a small quantity of free recrystallized grains are formed, and the well formed subgrains with clean high-angle boundaries and coarse precipitates seem to be remained during heat treatment. Under high Z parameter condition, a large number of fine equiaxed recrystallized grains are produced, and a high dislocation density with poorly developed cellularity and considerable fine dynamic precipitates are replaced by the well formed subgrains and relatively coarse precipitates after heat treatment. The average recrystallized grain size after heat treatment decreases with increasing Z value and a quantitative relation between the average grain size and the Z value is obtained.展开更多
The corrosion resistance of Al？Zn？Mg alloy subjected to different times in flame rectification was investigated based on the exfoliation corrosion test. The results indicate that the flame rectification deteriorate...The corrosion resistance of Al？Zn？Mg alloy subjected to different times in flame rectification was investigated based on the exfoliation corrosion test. The results indicate that the flame rectification deteriorates the exfoliation corrosion resistance of Al？Zn？Mg alloy. The corrosion resistance of Al-Zn-Mg alloy is ranked in the following order： base metal〉two times〉three times〉one time of flame rectification. The exfoliation corrosion behavior was discussed based on the transformation of precipitates at grain boundaries and matrix. With increasing the number of times in flame rectification, the precipitate-free zones disappeared and the precipitates experienced dissolution and re-precipitation. The sample was seriously corroded after one time of flame rectification, because the precipitates at grain boundaries are more continuous than those in other samples.展开更多
A short process without solution treatment was developed to manufacture Cu-2.3Fe-0.03 P alloy strips. After hot rolling-quenching and cold rolling with 80% reduction, the alloy exhibited excellent resistance to recrys...A short process without solution treatment was developed to manufacture Cu-2.3Fe-0.03 P alloy strips. After hot rolling-quenching and cold rolling with 80% reduction, the alloy exhibited excellent resistance to recrystallization softening. The hardness and electrical conductivity of Cu-Fe-P alloy under different thermomechanical treatments were measured by hardness tester and double bridge tester, respectively, and the microstructure of the alloy was examined by optical microscopy and transmission electron microscopy. The results show that the finished product of Cu-2.3Fe-0.03 P alloy was strengthened by work hardening, while the Fe precipitates with the size of about 25 nm stabilized the cold rolled structure. The conductivity decreased during cold rolling, especially for the pre-aged specimens, because the fine precipitates with the size smaller than 5 nm re-dissolved easily into the matrix. A Cu-Fe-P alloy with an electrical conductivity of 66% IACS and a hardness of HV 134 can be gained.展开更多
Al-x%Sc-0.11%Zr alloys （x=0, 0.02, 0.05, 0.08, 0.11, 0.15） were produced by a chill cast procedure. The effect of Sc content on the precipitation of Al3（Sc,Zr） during heat treatment at 475 °C for 12 h was stu...Al-x%Sc-0.11%Zr alloys （x=0, 0.02, 0.05, 0.08, 0.11, 0.15） were produced by a chill cast procedure. The effect of Sc content on the precipitation of Al3（Sc,Zr） during heat treatment at 475 °C for 12 h was studied. Nucleation, precipitation and distribution of Al3（Sc,Zr） precipitates were found to be strongly related to the Sc content. With increasing the Sc content, the average radius of the precipitates decreases, while the number density of the precipitates increases, as investigated by transmission electron microscopy （TEM）. The distribution of the precipitates becomes more and more homogeneous when the Sc content is increased. The recrystallization resistance of samples that was 90% cold rolled and isothermal annealed for half an hour in the temperature range of 200-600 °C was investigated. The results show that the recrystallization temperature varies from 250 °C for the alloy without Sc to about 600 °C for the alloy containing 0.15% Sc because of the high density of Al3（Sc,Zr） precipitates.展开更多
The hot deformation behavior of 7A55 aluminum alloy was investigated at the temperature ranging from 300 ℃ to 450 ℃ and strain rate ranging from 0.01 s-1 to 1 s-1 on a Gleeble-3500 simulator. Processing maps were es...The hot deformation behavior of 7A55 aluminum alloy was investigated at the temperature ranging from 300 ℃ to 450 ℃ and strain rate ranging from 0.01 s-1 to 1 s-1 on a Gleeble-3500 simulator. Processing maps were established in order to apprehend the kinetics of hot deformation and the rate controlling mechanism was interpreted by the kinetic rate analysis obeying power-law relation. The results indicated that one significant domain representing dynamic recrystallization （DRX） existed on the processing maps and lying in 410-450 ＆#176;C and 0.05-1 s-1. The conclusions of kinetic analysis correlated well with those obtained from processing maps. The apparent activation energy values calculated in the dynamic recrystallization （DRX） domain and the stability regions except dynamic recrystallization （DRX） domain were 91.2 kJ/mol and 128.8 kJ/mol, respectively, which suggested that grain boundary self-diffusion and cross-slip were the rate controlling mechanisms.展开更多
The hot compression tests of Al-Zn-Mg-Cu-Zr aluminum alloys （7056 alloy and 7150 alloy） were performed in a temperature range from 300 to 450 °C and at strain rate range from 0.01 to 10 s-1. The results show th...The hot compression tests of Al-Zn-Mg-Cu-Zr aluminum alloys （7056 alloy and 7150 alloy） were performed in a temperature range from 300 to 450 °C and at strain rate range from 0.01 to 10 s-1. The results show that the true stress-true strain curves exhibit a peak stress at a critical strain, then the flow stresses decrease monotonically until high strains, showing a dynamic flow softening. The peak stresses depend on the temperature compensated strain rate, which can be represented by the Zener-Hollomon parameter Z in the hyperbolic-sine equation with hot deformation activation energy of 244.64 kJ/mol for 7056 alloy and 229.75 kJ/mol for 7150 alloy, respectively, while the peak stresses for the former are lower than those for the latter under the similar compression condition. The deformed microstructures consist of a great amount of precipitates within subgrains in the elongated grains at high Z value and exhibit well formed subgrains in the recrystallized grains at low Z value. The smaller subgrains and greater density of fine precipitates in 7150 alloy are responsible for the high peak stresses because of the substructural strengthening and precipitating hardening compared with 7056 alloy.展开更多
文摘目的观察一种新型血液透析技术—内源性再输注血液透析滤过(hemodiafiltration with endogenous reinfusion,HFR)对缓解血液透析患者瘙痒症状的效果。方法行前后对照研究,比较患者HFR治疗前、后瘙痒症状、睡眠质量、生活质量和相关实验室检查指标。结果HFR治疗前、后瘙痒严重程度(Z=-2.023,P=0.043)、睡眠质量(t=7.318,P<0.001)和生活质量(t=4.804,P=0.003)差异均有统计学意义。结论HFR治疗在一定程度上可减轻尿毒症患者的瘙痒症状,改善其睡眠质量和生活质量。
基金Projects (2008CB617608, 2009CB623704) supported by the National Basic Research Program of China
文摘2026 aluminum alloy was compressed in a temperature range of 300-450 ℃ and strain rate range of 0.01-10 s^-1. The correlation between compression conditions and microstructural evolution after solution and aging heat treatment was investigated. It is found that the recrystallization and precipitation behavior after heat treatment are associated with the temperature compensated strain rate Z value during hot deformation. Under low Z parameter condition, a small quantity of free recrystallized grains are formed, and the well formed subgrains with clean high-angle boundaries and coarse precipitates seem to be remained during heat treatment. Under high Z parameter condition, a large number of fine equiaxed recrystallized grains are produced, and a high dislocation density with poorly developed cellularity and considerable fine dynamic precipitates are replaced by the well formed subgrains and relatively coarse precipitates after heat treatment. The average recrystallized grain size after heat treatment decreases with increasing Z value and a quantitative relation between the average grain size and the Z value is obtained.
基金Projects(51374048,50904012)supported by the National Natural Science Foundation of China
文摘The corrosion resistance of Al？Zn？Mg alloy subjected to different times in flame rectification was investigated based on the exfoliation corrosion test. The results indicate that the flame rectification deteriorates the exfoliation corrosion resistance of Al？Zn？Mg alloy. The corrosion resistance of Al-Zn-Mg alloy is ranked in the following order： base metal〉two times〉three times〉one time of flame rectification. The exfoliation corrosion behavior was discussed based on the transformation of precipitates at grain boundaries and matrix. With increasing the number of times in flame rectification, the precipitate-free zones disappeared and the precipitates experienced dissolution and re-precipitation. The sample was seriously corroded after one time of flame rectification, because the precipitates at grain boundaries are more continuous than those in other samples.
基金Project supported by Central South University Postdoctoral Science FoundationProject(CSUZC2013019)supported by the Open Fund for the Precision Instruments of Central South University,ChinaProject(CSUZC201522)supported by the Open-End Fund for the Valuable and Precision Instruments of Central South University,China
文摘A short process without solution treatment was developed to manufacture Cu-2.3Fe-0.03 P alloy strips. After hot rolling-quenching and cold rolling with 80% reduction, the alloy exhibited excellent resistance to recrystallization softening. The hardness and electrical conductivity of Cu-Fe-P alloy under different thermomechanical treatments were measured by hardness tester and double bridge tester, respectively, and the microstructure of the alloy was examined by optical microscopy and transmission electron microscopy. The results show that the finished product of Cu-2.3Fe-0.03 P alloy was strengthened by work hardening, while the Fe precipitates with the size of about 25 nm stabilized the cold rolled structure. The conductivity decreased during cold rolling, especially for the pre-aged specimens, because the fine precipitates with the size smaller than 5 nm re-dissolved easily into the matrix. A Cu-Fe-P alloy with an electrical conductivity of 66% IACS and a hardness of HV 134 can be gained.
基金Project (CDJZR12130048) supported by the Fundamental Research Funds for the Central Universities of ChinaProject supported by the Research Council of Norway
文摘Al-x%Sc-0.11%Zr alloys （x=0, 0.02, 0.05, 0.08, 0.11, 0.15） were produced by a chill cast procedure. The effect of Sc content on the precipitation of Al3（Sc,Zr） during heat treatment at 475 °C for 12 h was studied. Nucleation, precipitation and distribution of Al3（Sc,Zr） precipitates were found to be strongly related to the Sc content. With increasing the Sc content, the average radius of the precipitates decreases, while the number density of the precipitates increases, as investigated by transmission electron microscopy （TEM）. The distribution of the precipitates becomes more and more homogeneous when the Sc content is increased. The recrystallization resistance of samples that was 90% cold rolled and isothermal annealed for half an hour in the temperature range of 200-600 °C was investigated. The results show that the recrystallization temperature varies from 250 °C for the alloy without Sc to about 600 °C for the alloy containing 0.15% Sc because of the high density of Al3（Sc,Zr） precipitates.
基金Project(2012CB619505)supported by the National Basic Research Program of China
文摘The hot deformation behavior of 7A55 aluminum alloy was investigated at the temperature ranging from 300 ℃ to 450 ℃ and strain rate ranging from 0.01 s-1 to 1 s-1 on a Gleeble-3500 simulator. Processing maps were established in order to apprehend the kinetics of hot deformation and the rate controlling mechanism was interpreted by the kinetic rate analysis obeying power-law relation. The results indicated that one significant domain representing dynamic recrystallization （DRX） existed on the processing maps and lying in 410-450 ＆#176;C and 0.05-1 s-1. The conclusions of kinetic analysis correlated well with those obtained from processing maps. The apparent activation energy values calculated in the dynamic recrystallization （DRX） domain and the stability regions except dynamic recrystallization （DRX） domain were 91.2 kJ/mol and 128.8 kJ/mol, respectively, which suggested that grain boundary self-diffusion and cross-slip were the rate controlling mechanisms.
基金Projects (2008CB617608, 2009CB623704) supported by the National Basic Research Program of China
文摘The hot compression tests of Al-Zn-Mg-Cu-Zr aluminum alloys （7056 alloy and 7150 alloy） were performed in a temperature range from 300 to 450 °C and at strain rate range from 0.01 to 10 s-1. The results show that the true stress-true strain curves exhibit a peak stress at a critical strain, then the flow stresses decrease monotonically until high strains, showing a dynamic flow softening. The peak stresses depend on the temperature compensated strain rate, which can be represented by the Zener-Hollomon parameter Z in the hyperbolic-sine equation with hot deformation activation energy of 244.64 kJ/mol for 7056 alloy and 229.75 kJ/mol for 7150 alloy, respectively, while the peak stresses for the former are lower than those for the latter under the similar compression condition. The deformed microstructures consist of a great amount of precipitates within subgrains in the elongated grains at high Z value and exhibit well formed subgrains in the recrystallized grains at low Z value. The smaller subgrains and greater density of fine precipitates in 7150 alloy are responsible for the high peak stresses because of the substructural strengthening and precipitating hardening compared with 7056 alloy.
