基于聚偏二氟乙烯压电传感器,对铜靶材中纳秒激光脉冲诱导的冲击波传播过程进行了实验研究,给出了铜靶材内冲击压强随激光脉冲能量和靶材厚度的变化规律.实验结果表明:500 m J激光脉冲能量作用到2 mm厚的铜靶材产生的冲击压强达到2.1 M...基于聚偏二氟乙烯压电传感器,对铜靶材中纳秒激光脉冲诱导的冲击波传播过程进行了实验研究,给出了铜靶材内冲击压强随激光脉冲能量和靶材厚度的变化规律.实验结果表明:500 m J激光脉冲能量作用到2 mm厚的铜靶材产生的冲击压强达到2.1 MPa;激光脉冲能量从200 m J增加到500 m J,在铜靶材厚度为2和4 mm条件下,冲击压强分别增加了162%和231%;而当铜靶材厚度从2 mm增加到6 mm时,在400和500 m J激光脉冲能量作用下,铜靶材内冲击压强分别降低了32%和49%.展开更多
Semi-solid processing of A380 aluminum alloy was performed by gas induced semi-solid(GISS)process.The effects of argon inert gas flow rate,starting temperature and duration of gas purging as key GISS parameters and al...Semi-solid processing of A380 aluminum alloy was performed by gas induced semi-solid(GISS)process.The effects of argon inert gas flow rate,starting temperature and duration of gas purging as key GISS parameters and also modification with Sr on the structural refinements,hardness and impact strength of GISS alloys were investigated.Microstructural evolution shows that there is an important effect of the pouring temperature and Sr addition on the morphology and size of primaryα(A1)in the alloy to change from coarse dendritic to fine globular structure.The best sample which has fine grains of 51.18μm in average size and a high level of globularity of 0.89 is achieved from a GISS processing of Sr modified alloy in which the gas purging started at 610℃.The impact strength of the GISS optimized samples((4.67±0.18)J/cm^(2))shows an increase of about 40%with respect to the as-cast sample due to the globular structure and fibrous Si morphology.Moreover,the hardness of the optimized GISS sample((89.34±2.85)HB)increases to(93.84±3.14)HB by modification with the Sr and GISS process.The fracture surface of Sr modified alloy is also dominated by complex topography showing typical ductile fracture features.展开更多
文摘基于聚偏二氟乙烯压电传感器,对铜靶材中纳秒激光脉冲诱导的冲击波传播过程进行了实验研究,给出了铜靶材内冲击压强随激光脉冲能量和靶材厚度的变化规律.实验结果表明:500 m J激光脉冲能量作用到2 mm厚的铜靶材产生的冲击压强达到2.1 MPa;激光脉冲能量从200 m J增加到500 m J,在铜靶材厚度为2和4 mm条件下,冲击压强分别增加了162%和231%;而当铜靶材厚度从2 mm增加到6 mm时,在400和500 m J激光脉冲能量作用下,铜靶材内冲击压强分别降低了32%和49%.
文摘Semi-solid processing of A380 aluminum alloy was performed by gas induced semi-solid(GISS)process.The effects of argon inert gas flow rate,starting temperature and duration of gas purging as key GISS parameters and also modification with Sr on the structural refinements,hardness and impact strength of GISS alloys were investigated.Microstructural evolution shows that there is an important effect of the pouring temperature and Sr addition on the morphology and size of primaryα(A1)in the alloy to change from coarse dendritic to fine globular structure.The best sample which has fine grains of 51.18μm in average size and a high level of globularity of 0.89 is achieved from a GISS processing of Sr modified alloy in which the gas purging started at 610℃.The impact strength of the GISS optimized samples((4.67±0.18)J/cm^(2))shows an increase of about 40%with respect to the as-cast sample due to the globular structure and fibrous Si morphology.Moreover,the hardness of the optimized GISS sample((89.34±2.85)HB)increases to(93.84±3.14)HB by modification with the Sr and GISS process.The fracture surface of Sr modified alloy is also dominated by complex topography showing typical ductile fracture features.
