一种生物分子马达的冲激力模型

基于动力冲程模型并结合布朗棘轮模型的扩散机制,提出了分子马达的冲激力模型。该模型基于一系列具有时间或空间周期性的δ函数来模拟分子马达的做功冲击,得到了关于几率流(速度)的解析结果。计算结果与实验数据相符合。为了产生非零的几率流,新模型并不要求分子马达与轨道间的势能必须是不对称的,因而相对于布朗棘轮模型来说更加稳健。

Microstructure and mechanical properties of pulsed laser welded Al/steel dissimilar joint

Pulsed laser welding was used in joining pure aluminum to stainless steel in a lap joint configuration. It is found that the mechanical properties of the laser joints were closely correlated with the bead geometry, i.e., penetration depth. In order to study the correlation, two typical laser welds with different penetration depths were analyzed. In high penetration depth (354 μm) joint, Al-rich Fe?Al IMCs with microcracks were formed at the Al/fusion zone (FZ) interface. The joint strength was found to be (27.2±1.7) N/mm and three failure modes were observed near the Al/FZ interface. In low penetration depth (108 μm) joint, Fe-rich Fe?Al IMCs without any defect were formed at the Al/FZ interface. The joint strength was found to be (46.2±1.9) N/mm and one failure mode was observed across the FZ.

Prediction about residual stress and microhardness of material subjected to multiple overlap laser shock processing using artificial neural network

In this work,the nickel-based powder metallurgy superalloy FGH95 was selected as experimental material,and the experimental parameters in multiple overlap laser shock processing(LSP)treatment were selected based on orthogonal experimental design.The experimental data of residual stress and microhardness were measured in the same depth.The residual stress and microhardness laws were investigated and analyzed.Artificial neural network(ANN)with four layers(4-N-(N-1)-2)was applied to predict the residual stress and microhardness of FGH95 subjected to multiple overlap LSP.The experimental data were divided as training-testing sets in pairs.Laser energy,overlap rate,shocked times and depth were set as inputs,while residual stress and microhardness were set as outputs.The prediction performances with different network configuration of developed ANN models were compared and analyzed.The developed ANN model with network configuration of 4-7-6-2 showed the best predict performance.The predicted values showed a good agreement with the experimental values.In addition,the correlation coefficients among all the parameters and the effect of LSP parameters on materials response were studied.It can be concluded that ANN is a useful method to predict residual stress and microhardness of material subjected to LSP when with limited experimental data.

Recent Advances in ZnO Films Prepared by Pulsed Laser Deposition

Pulsed laser deposition(PLD) is emerging as the most rapid and efficient technique for fabricating the many compound films. ZnO thin films can be prepared under various deposition conditions by PLD. The effects of various substrate temperature, oxygen partial pressure, annealing temperature, substrate, buffer layers thickness and film thickness on micro-structural, optical and electrical properties of ZnO films grown by PLD technology are reviewed. ZnO films with special function can grow under proper conditions by PLD.

Simulation and prediction in laser bending of silicon sheet

The laser bending of single-crystal silicon sheet （0.2 mm in thickness） was investigated with JK701 Nd：YAG laser. The models were developed to describe the beam characteristics of pulsed laser. In order to simulate the process of laser bending, the FEM software ANSYS was used to predict the heat temperature and stress-strain fields. The periodic transformation of temperature field and stress-strain distribution was analyzed during pulsed laser scanning silicon sheet. The results indicate that the mechanism of pulsed laser bending silicon is a hybrid mechanism in silicon bending, rather than a simple mechanism of TGM or BM. This work also gets silicon sheet bent after scanning 6 times with pulsed laser, and its bending angle is up to 6.5°. The simulation and prediction results reach well agreement with the verifying experiments.

Impact of substrate on opto-thermal response of thin metallic targets under irradiation with femtosecond laser pulses

Femtosecond pulsed lasers have been widely used over the past decades due to their capability to fabricate precise patterns at the micro-and nano-lengths scales. A key issue for efficient material processing is the determination of the laser parameters used in the experimental set ups. Despite a systematic investigation that has been performed to highlight the impact of every parameter independently, little attention has been drawn on the role of the substrate material on which the irradiated solid is placed. In this work, the influence of the substrate is emphasised for films of various thicknesses, which demonstrates that both the optical and thermophysical properties of the substrate affect the thermal fingerprint on the irradiated film while the impact is manifested to be higher at smaller film sizes. Two representative materials, silicon and fused silica, have been selected as typical substrates for thin films(gold and nickel) of different optical and thermophysical behaviour and the thermal response and damage thresholds are evaluated for the irradiated solids. The pronounced influence of the substrate is aimed to pave the way for new and more optimised designs of laserbased fabrication set ups and processing schemes.

Femtosecond Optical Trapping of Cells:Efficiency and Viability

The femtosecond optical trapping capability and the effect of femtosecond laser pulses on cell viability were studied.The maximum lateral velocity at which the particles just failed to be trapped,together with the measured average trapping power,were used to calculate the lateral trapping force(Q-value) .The viability of the cells after femtosecond laser trapping was ascertained by vital staining.Measurement of the Q-values shows that femtosecond optical tweezers are just as effective as continuous wave optical tweezers.The experiments demonstrate that there is a critical limit for exposure time at each corresponding laser power of femtosecond optical tweezers,and femtosecond laser tweezers are safe for optical trapping at low power with short exposure time.

A study on equivalent circuit model of lead-acid battery for electric vehicles

A 100Ah@42V lead-acid battery package for electric vehicles are used for study. 1he hybrid pulse test is applied to the battery package to acquire enough data, by which the partnership for a new generation of vehicles （PNGV） equivalent circuit model parameters are identified by the least square method. Then, the PNGV model is verified under two conditions, i.e., the composite pulse excitation and the constant-current respectively. The corresponding maximum relative errors of output voltage are less than 3 % and 3.5 %. Results show that the present PNGV equivalent circuit model and verification method is effective, which can satisfy requirement of simulation of power system of electric vehicles.

Effects of Relativistic and Ponderomotive Nonlinearities on an Intense Laser Pulse Propagation in a Plasma Channel

The optical guiding of a moderately intense laser pulse in a parabolic preformed plasma channel is analyzed by means of the variational method.Relativistic,ponderomotive and their coupling nonlinearities are included.The conditions for periodic defocusing and focusing,as well as constant spot size propagation are given.It is found that the laser focusing is released by the coupling of relativistic and ponderomotive nonlinearities.

Intrinsic exchange bias effect in strain-engineered single antiferromagnetic LaMnO3 films

In this work, epitaxial growth of LaMnO3 thin films on different substrates using pulsed laser deposition under tensile and compressive strain was studied. The intrinsic exchange bias effect was observed in the single A-type antiferromagnetic LaMnO3 films no matter whether the tensile or compressive strain was supplied by the substrates. Due to the lattice mismatch between the film and different substrates, the intense strain can induce MnO6 octahedral rotation in the bottom region of the film neighboring the substrate, which leads to the distortion of MnO6 octahedron and the net magnetic behavior. However, the upper part maintains the original A-type antiferromagnetic order due to strain relaxation. The exchange bias effect in single films is attributed to the coupling between the bottom canted magnetic part and the upper antiferromagnetic region. The observation of exchange bias in single films on different substrates enables the emergence of a new class of biasing components in spintronics, which are based on strain-engineering.

Microscopic Dynamics of Nonsequential Double Ionization by Elliptically Polarized Few-Cycle Laser Pulses

With the classical ensemble model, we investigate nonsequential double ionization （NSDI） of xenon atoms using 780 nm, 0.25 PW/cm2 elliptically polarized few-cycle laser pulses. The momentum distribution of correlated electron along the long axis o~ the laser polarization plane shows an obvious V-like structure locating at the third quadrant, and the momentum along the short axis of the laser polarization plane are mainly distributed in the second and fourth quadrants. Moreover, we demonstrate that the Coulomb repulsion interaction plays a decisive role to the above results. By back analyzing the class/ca/ trajectories of NSDI, we find that there are two kinds of recollision trajectories mainly contribute to NSDI, and the different microscopic dynamics for the two kinds of trajectories are clearly explored.

Pulse laser induced graphite-to-diamond phase transition： the role of quantum electronic stress

First-principles calculations show that the pulse laser induced graphite-to-diamond phase transition is related to the lattice stress generated by the excited carriers,termed as "quantum electronic stress(QES)".We found that the excited carriers in graphite generate a large anisotropic QES that increases linearly with the increasing carrier density.Using the QES as a guiding parameter,structural relaxation spontaneously transforms the graphite phase into the diamond phase,as the QES is reduced and minimized.Our results suggest that the concept of QES can be generally applied as a good measure to characterize the pulse laser induced phase transitions,in analogy to pressure induced phase transitions.

Characteristic and Mechanism of Pressure Fluctuation Caused by Self-Induced Oscillation of Supersonic Impinging Jet

When the underexpanded supersonic jet impinges on the obstacle, it is well known that the self-induced flow os- cillation occurs. This oscillation depends on the pressure ratio in the flowfield, the position of an obstacle and is related with the noise problems of aeronautical and other industrial engineering. The characteristic and the mechanism of self-induced flow oscillation, have to be clarified to control various noise problems. But, it seems that the characteristics of the oscillated flowfield and the mechanism of an oscillation have to be more cleared to control the oscillation. This paper aims to clarify the effect of the pressure ratio and the obstacle position and the mechanism of self-induced flow oscillation by numerical analysis and experiment, when the underexpanded su- personic jet impinges on the cylindrical body. From the result of this study, it is clear that occurrence of the self-induced flow osciUation depends on the pressure balance in the flowfield.