一种降低ADI-FDTD算法数值色散的准各向同性空间差分法

使用准各向同性的空间差分格式替代常规ADI-FDTD算法中的差分形式来改善原算法中的数值色散问题。修正后的算法依然保持了无条件稳定的优势;同时,通过合理选择加权系数,仿真过程中的数值色散误差可以显著降低。推导出了修正算法的数值色散关系,并从入射角、时间步长和网格尺寸等3个方面分析了修正算法数值色散问题的改进程度。最后,通过一个算例对比演示了改进算法的精度和计算效率。

基于差分精准定位技术和GIS平台的铁路安全生产管理系统运用实践

通过对重载铁路当前安全生产管理现状进行阐述和分析,提出一种能够适应新趋势发展要求的铁路安全生产管理系统。系统采用“三层平台,两层应用”设计实现,通过新技术与货运铁路行业应用充分结合实践,取得良好效果,满足铁路安全生产管理全生命周期、全流程、全要素的“可感”、“可知”、“可测”、“可视”、“可控”的闭环管理的要求,在铁路运输生产管理方面能辅助各层级管理人员进行生产决策,有效提高运输效率,改善行车组织方式,对于依托新技术的新运维管理模式在行业内推广具有重要意义。

特殊差分方程的求解

贝努里差分方程、恰当差分方程与准恰当差分方程等三类特殊的差分方程都可以用变量代换或积的差分公式来求解,首次给出贝努里差分方程、恰当差分方程与准恰当差分方程的定义、求解方法以及解的一般形式.作为应用又给出了与三类特殊差分方程相关的具体实例,并给出了它们的解.

8通道10b的R-C混合式SAR ADC的设计

实现一个8通道10 b转换精度的逐次逼近式(SAR)模拟-数字转换器。在DAC的设计上采用新的电阻电容混合式的DAC的结构,和传统的C-R式结构相比具有更小的面积。同时对比较器的设计进行了优化,采用一个三级级联的准差分结构,并设计在传统的前置预放和锁存器级联的理论基础上,引入了交叉耦合负载,复位、钳位技术,获得了高精度和较低的功耗。设计经HSPICE仿真结果证明有效,并采用0.13μm CMOS工艺,分别采用2.5 V的模拟电源电压和1.2 V的数字电源电压供电,实现10位的精度。芯片面积为480μm*380μm,FF case下功耗为0.54 mW。实现了超低功耗的ADC的设计。

GPS数据事后处理方法研究

介绍了准载波相位事后差分GPS和相对GPS两种GPS数据事后处理方法,利用GPS数据事后处理方法能显著提高GPS定位精度,且现场测试过程中无须基准站精确坐标,没有大量数据的实时传输和解算.

强迫耗散非线性发展方程与完全平方守恒格式

从描述大气和海洋运动的强迫耗散非线性发展方程出发 ,对强迫耗散非线性大气和海洋方程组显式差分格式的计算稳定性进行了分析 ,构造了一类强迫耗散非线性发展方程的显式准完全平方守恒差分格式。理论分析和数值试验证明 ,这类显式准完全平方守恒差分格式是计算稳定的 ,值得推广应用。

计算地球流体力学的回顾、进展及展望

简要回顾了计算地球流体力学的发展历史,概括介绍了计算地球流体力学的研究进展及最新发展方向。针对线性发展方程的计算稳定性问题,介绍了判定线性发展方程初值问题的稳定性判别条件:CLF条件。对分析线性偏微分方程差分格式计算稳定性判据的Fourier方法、启发性稳定性分析方法,也做了简要的介绍。同时,重点介绍了判定线性发展方程初边值问题计算稳定性的GKS理论。在非线性发展方程的计算稳定性方面,重点介绍的主要内容包括:非线性发展方程的计算紊乱现象和计算不稳定的原因;克服非线性发展方程计算不稳定的方法;瞬时平方守恒型差分格式的构造;隐式和显式完全平方守恒格式的设计;强迫耗散非线性发展方程的计算稳定性问题。在计算地球流体力学的近期进展方面,重点介绍了非线性发展方程的计算稳定性与初值的关系,强迫耗散非线性发展方程显式准完全平方守恒格式的构造。对计算地球流体力学需要进一步研究的问题,也做了简要介绍。这些研究工作的介绍,无疑对推动计算地球流体力学的研究和大气海洋模式的研制具有一定的指导意义。

Effect of Varieties on Tea Pigment and Chromatic Aberration of Black Tea Infusion

Effects of varieties on the content of tea pigment, L＊, a＊ and b＊ value of chromatic aberration of black tea infusion was studied. The correlation relationship between content of TF, TR, TB and L＊, a＊, b＊ value was extremely significant at P＆lt;0.05. Fresh tea leaves with plucking standard of 1 bud and 2 leaves could man-ufacture black tea with higher content of tea pigment, higher a＊ and b＊ value but lower L＊ value, than those of plucking standard of 1 bud and 3 leaves. But the discrepancy of certain parameter of the two plucking standards changed with vari-eties. Varieties’ quality potential could be concealed by improper plucking standards. Six varieties were divided into four groups on the basis of gross tea polyphenols in fresh tea leaves （GTP）, consumption of tea polyphenols to gross tea polyphenols ratio （CTP/GTP） and gross tea pigment to consumption of tea polyphenols ratio （GP/CTP）. Hybrid performed the very suitability of black tea manufacturing. To en-sure high quality of made black tea, suitable variety should be chosen and reason-able plucking standard also should be taken into consideration.

Membrane preconcentration of iron in seawater samples and on-site determination in spectrophotometry

A novel method for on-site determination of trace iron was developed using membrane preconcentration and spectrophotometric detection. Fe（II）-ferrozine complex was reacted with cetyltrimethylammonium bromide （CTAB） to form a Fe（II）-ferrozine-CTAB paired compound, which was collected on a membrane by filtration under vacuum. The membrane was immersed in 2 mL of ethanol-nitric acid and the absorbance of the solution measured for quantitative analysis. Various factors affecting the iron collection and determination were investigated. With different sample preconcentration volumes, the range of determination was broadened to 0.5-120 ~tg/L. The detection limit of this method reached 0.19 ktg/L and the recoveries were between 97.2 and 109% when the concentration enrichment was about 45. The relative standard deviation （n = 7） was 1.9% for samples containing 10 ~g/L Fe. Twelve seawater samples were analyzed on-site using the proposed method, and two were also analyzed in inductively coupled plasma mass spectrometry. No significant difference was shown between the two methods by the Student＇s t-test. The method has also been used on-site for iron enrichment experiments with phytoplankton and concluded to be simple, accurate and inexpensive.

Pure quasi-P wave equation and numerical solution in 3D TTI media

Based on the pure quasi-P wave equation in transverse isotropic media with a vertical symmetry axis （VTI media）, a quasi-P wave equation is obtained in transverse isotropic media with a tilted symmetry axis （TTI media）. This is achieved using projection transformation, which rotates the direction vector in the coordinate system of observation toward the direction vector for the coordinate system in which the z-component is parallel to the symmetry axis of the TTI media. The equation has a simple form, is easily calculated, is not influenced by the pseudo-shear wave, and can be calculated reliably when δ is greater than ε. The finite difference method is used to solve the equation. In addition, a perfectly matched layer （PML） absorbing boundary condition is obtained for the equation. Theoretical analysis and numerical simulation results with forward modeling prove that the equation can accurately simulate a quasi-P wave in TTI medium.

Application of the Wavelet Packet Method in Discrimination Between Nuclear Explosion and Earthquake

Although the CTBT (Comprehensive Nuclear Test Ban Treaty) was passed in 1996, it is still necessary to develop new and highly efficient methods (Wu Zhongliang, Chen Yuntai, et al., 1993; Xu Shaoxie, et al.1994; Richard L. Garwin, 1994) to monitor possible events. Many discrimination criteria (Xu Shaoxie, et al.,1994; Institute of Geophysics, Chinese Academy of Sciences, 1976; Richard L. Garwin, 1994) have been put forward since the 1950s. The results show that each of the existing criteria has its own limitation, but the seismological method is an important and efficient method in the discrimination between nuclear explosion and earthquake. Especially in recent years, because of the little and little equivalent as well as the increasing hiding steps used in the test, a number of more efficient seismological methods have been worked out. In this paper, a new discrimination method, the Wavelet Packet Component Ratio (WPCR) method, is put forward. This method makes full use of the difference in variation with time between the spectra of nuclear explosions and earthquakes. Its discrimination efficiency is rather high.

Automatically detecting auditory P300 in several trials

A method was demonstrated based on Infomax independent component analysis(Infomax ICA) for automatically extracting auditory P300 signals within several trials. A signaling equilibrium algorithm was proposed to enhance the effectiveness of the Infomax ICA decomposition. After the mixed signal was decomposed by Infomax ICA, the independent component(IC) used in auditory P300 reconstruction was automatically chosen by using the standard deviation of the fixed temporal pattern. And the result of auditory P300 was reconstructed using the selected ICs. The experimental results show that the auditory P300 can be detected automatically within five trials. The Pearson correlation coefficient between the standard signal and the signal detected using the proposed method is significantly greater than that between the standard signal and the signal detected using the average method within five trials. The wave pattern result obtained using the proposed algorithm is better and more similar to the standard signal than that obtained by the average method for the same number of trials. Therefore, the proposed method can automatically detect the effective auditory P300 within several trials.

Feasibility of central loop TEM method for prospecting multilayer water-fi lled goaf

With deep mining of coal mines, prospecting multilayer water-filled goaf has become a new content that results from geophysical exploration in coalfields. The central loop transient electromagnetic （TEM） method is favorable for prospecting conductive layers because of the coupling relationship between its field structure and formation. However, the shielding effect of conductive overburden would not only require a longer observation time when prospecting the same depth but also weaken the anomalous response of underlying layers. Through direct time domain numerical simulation and horizontal layered earth forward modeling, this paper estimates the length of observation time required to prospect the target, and the distinguishable criterion of multilayer water-filled goal is presented with observation error according to the effect of noise on observation data. The observed emf curves from Dazigou Coal Mine, Shanxi Province can distinguish multilayer water-filled goaf. In quantitative inversion interpretation of observed curves, using electric logging data as initial parameters restrains the equivalence caused by coal formation thin layers. The deduced three-layer and two-layer water-filled goals are confirmed by the drilling hole. The result suggests that when observation time is long enough and with the anomalous situation of underlying layers being greater than the observation error, the use of the central loop TEM method to orosoect a multilaver water-filled goaf is feasible.

Study on the Determination of Trace Ni(II) by the Catalytic Kinetic Spectrophotometric Method

A new kinetic spectrophotometric method has been developed for the determination of trace Ni （Ⅱ in natural water. The method is based on the catalytic effect of Ni （Ⅱ） on the oxidation of weak acid brilliant blue dye （RAWL） by KIO4 in acid medium. The concentration of nickel （Ⅱ） can be determined spectrophotometrically by measuring the decrease of absorbance of RAWL at λ = 626 nm using the fix-time method. The influencing factors are investigated by the orthogonal experimental design. The obtained optimum analytical conditions are： pH = 2.00, CRAWL = 5.00×10^-5 mol·L^-1, c KlO4 = 2.00× 10^-5 mol·L^-1, the reaction time t= 10min and the temperature T = 25 ℃. Under the optimum conditions, the developed method allows the measurement of Ni （Ⅱ） in a range of 0 - 40.0ngmL1. The standard deviation of eleven independent measurements of blank reaction is S = 3.08× 10^-3 and the limit of detection is 2.20ng·mL^-1. The relative standard deviations （RSDs） in six replicate determinations of 5 ngmL-1 and 8 ngmL1 Ni （Ⅱ） are 2.87% and 1.11%, respectively. Moreover, the experiments show few cations and anions can interfere with the measurement of Ni （Ⅱ）. The recovery efficiencies of this method are in a range of 97.0%-102.5% in freshwater samples. But there is a decreasing effect, which is about 0.2 times the added Ni （Ⅱ） in seawater medium. After reasonable calibration this processing method is used for the determination of Ni （Ⅱ） in seawater samples successfully. The results show this developed method has high accuracy and precision, high sensitivity, large range of linearity and high speed. The method can, therefore, be employed at room temperature.

Chemical characterization and sources of PM2.5 at 12-h resolution in Guiyang, China

The increasing emission of primary and gaseous precursors of secondarily formed atmospheric particulate matter due to continuing industrial development and urbanization are leading to an increased public awareness of environmental issues and human health risks in China. As part of a pilot study, 12-h integrated fine fraction particulate matter （PM2.5） filter samples were collected to chemically characterize and investigate the sources of ambient particulate matter in Guiyang City, Guizhou Province, southwestern China. Results showed that the 12-h integrated PM2.5 concentrations exhibited a daytime average of 51 ± 22 μg m^-3 （mean -4- standard deviation） with a range of 17-128 μg m^-3 and a nighttime average of 55 ± 32 μg m^-3 with a range of 4-186 μg m^-3. The 24-h integrated PM2.5 concentrations varied from 15 to 157 μg m^-3, with amean value of 53 ± 25 μg m^-3, which exceeded the 24-h PM2.5 standard of 35μg m^-3 set by USEPA, but was below the standard of 75 μg m^-3, set by China Ministry of Environmental Protection. Energy-dispersive X-ray fluorescence spectrometry （XRF） was applied to determine PM2.5 chemical element concentrations. The order of concentrations of heavy metals in PM2.5 were iron （Fe） 〉 zinc （Zn） 〉 manganese （Mn） 〉 lead （Pb） 〉 arsenic （As）〉 chromium （Cr）. The total concentration of 18 chemical elements was 13 ± 2 μg m^-3, accounting for 25% in PM2.5, which is comparable to other major cities in China, but much higher than cities outside of China.

Analysis on Regional Difference of Development of Elderly Care Real Estate in Gannan Area

The continuous expansion of the scale of the elderly population and the continuous acceleration of elderly population ageing have had a profound impact on China＇s economy, society and family, especially for the development of China＇s pension indusby, in this paper, taking Ganzhou City as an example, the population size, population ageing rate, urbanization rate and residential area were analyzed using Z-Scores standardized data processing model from three aspects： the population development level, the real estate market maturity degree and the service development level. The proportion of the tertiary industry and other indicators were used to explore the suitability of the development of eldedy care real estate, and cluster analysis was used to classify the sample areas according to the suitability. The results show that the 18 counties and cities in Ganzhou City could be divided into three categories, areas with poor suitability, areas with development potential, key development areas. Finally, suggestions were put forward that the target market of the development of old-age real estate could be comprehensively analyzed by combining the population development trend of the region with its thoughts and concepts, social and economic development, the maturity of the real estate market and the development of the service industry to ensure the sustainable operation of the old-age real estate.

Research on Co-seismic Displacement of the Yutian MS7.3 Earthquake Based on the High Frequency Data of GNSS

After the Yutian M_S7.3 earthquake,the authors instantly collected 1Hz high frequency data of the 4 reference stations within 350 km around the epicenter,and calculated the GNSS data with the TRACK module. The results showed that:( 1) The co-seismic displacement of Yutian station,about 54 km from the epicenter,is the most obvious,particularly in the EW component,with a change of about 52.5 ± 11mm,which is more than three times the mean-square error of calculating precision.( 2) In the Yutian reference station,the biggest variation in the EW component appeared within 1 minute after the earthquake.( 3) The change in the NS component is not great.

Probability and Statistical Error of Soil Sampling on Patches Assimilated during Delineation of Precision Farming Management Zones

When precision fanning management zones （MZs） are delineated in an agricultural field for precision nutrient management, unsupervised classification and cluster analysis procedures using remote sensing image analysis software are performed. These unsupervised classification and cluster analysis procedures are performed on the basis of the assumption that grouping of data points into naturally occurring clusters reduces within zone variability. The problem is that, there are small patches of different soil types within each management zone that are regarded as insignificant by the farmer, and are assimilated within larger MZs. These will consequently make soils within a management zone to be inhomogeneous. The objective of this study was to determine the probability of soil sampling occurrences on patches assimilated during delineation of MZs after a cluster analysis was performed. The study was conducted on a 5.0 ha （25°05′34.46″ S and 28°18′30.01″ E） and a 24.4 ha （23°59′04.61″ S and 28°52′29.43″ E） fields in the Waterberg District of the Limpopo Province in South Africa. A bare-soil high resolution Quickbird satellite imagery of a conventionally tilled agricultural field was used to develop MZs in the field. Soils were sampled using systematic unaligned sampling on a 35.0 m and 30.0 m grids for the 24.4 ha and 5.0 ha fields, respectively. Probabilities were calculated based on percentage area assimilated during the cluster analysis procedure that was performed using remote sensing image analysis software. The results indicated that in the 24.4 ha field there were 2.5 ha patches of high and medium zones that were assimilated within the low zone, and thus making low zones non-homogeneous. After cluster analysis and assimilation of patches, the low zone in the 24.4 ha field increased by 45.5% （2.5 ha） while the high zone was 16.4% （2.4 ha） smaller in size. In the smaller field of 5.0 ha, the high zone, which was originally 3.20 ha, lost 0.37 ha （11.6%）, which was assimilated in either low or medium zone. The study indicates that unequal probability proportional to size sampling could be used to minimize error when sampling across precision farming MZs because typically the low, medium and high MZs are not of equal size and do not contribute equally towards the mean values of soil samples.

Assessment of Triazine Herbicides in Soil by Microwave-assisted Extraction Followed by Gas Chromatography Coupled to Mass Spectrometry Detection

An alternative and fast method for the analysis of a mixture of nine triazines herbicides in soil is presented. The method is based on MAE （microwave-assisted extraction） of herbicides using ethyl acetate as extractant. The economy in the use of solvents coupled with the decrease in extraction time and lower power consumption make MAE a technique that meets the principles of green chemistry. MAE operational parameters, extraction time, mass of the sample and extraction temperature, were optimized by RSM （response surface methodology）. Determination of analytes was completed using gas chromatograph coupled to mass spectrometry detection. The selected triazines could be efficiently extracted by the solvent at 80 ℃ for 10 min, with 80% output of maximum power. When the optimized method was applied to analysis samples, the recoveries of analytes ranged from 81.8 to 106.0% and relative standard deviations were lower than 8.41%. The method is stable and reasonable, which can be used for the determination of ninetriazine herbicides residues in soil.

Effects of Grain Angle on Reproducibility and Accurate Measurement of Moisture Content of Wood Samples Using a Pin-Style Moisture Meter

Studies were conducted on the effects of grain angle on reproducibility and accurate measurement of moisture content of four wood samples using a pin-style moisture meter. The wood samples were partitioned into four quadrants and moisture contents were measured along the grain direction in the first and second quadrants from 0 degree to 150 degrees insteps of 30 degrees. Experimental results indicated that the average moisture content remained constant as the grain angle increased. Repeated measurements of moisture content at different grain angles or points on the wood surface showed similar patterns of variation. Within-point standard deviations of the moisture contents were greater than between-point standard deviations. A non-destructive method of measuring moisture content at the same location or point on the wood surfaces could not be proposed because of the high variation of moisture content when repeated measurements were taken at the same point. Instead, accurate measurements of moisture content could be obtained at random positions within a radius of 30 mm from the point of intersection of the moisture content axis and the grain angle.