The purpose of this paper is to establish confidence in anticipated minimum bond strength for inflatable rock bolts by comparing the bond strength to variable geotechnical conditions using the rock mass rating （RMR）...The purpose of this paper is to establish confidence in anticipated minimum bond strength for inflatable rock bolts by comparing the bond strength to variable geotechnical conditions using the rock mass rating （RMR） system. To investigate a correlation between these parameters, the minimum bond strength of pull-out tested inflatable rock bolts was compared to the RMR of the rock in which these bolts were placed. Bond strength vs. RMR plots indicate that expected minimum bond strength is positively corre- lated with RMR; however, the correlation is not strong. Cumulative percent graphs indicate that 97~; of pull-out tests result in a minimum bond strength of 3.3 and 1.7 ton/m in RMR/〉 45 and 〈45, respectively. Although lower bond strengths are more commonly encountered in low RMR ground, high bond strengths are possible as well, yielding higher variability in bond strengths in low RMR ground. Bond strength of friction bolts relies on contact between the rock bolt and drill hole. Experience in Nevada indicates that RMR is known to affect both the quality and consistency of drill holes which likely affects bond strength. Drilling and bolting in low RMR ground is more sensitive to drilling and bolting practices, and strategies for maximizing bond strength in these conditions are discussed.展开更多
To research the reinforcement effect of a rock slope with group anchorage cables and the stress characteristics of pre-stressed anchorage cables in the fractured surface, the rock slope calculated model of a wedge blo...To research the reinforcement effect of a rock slope with group anchorage cables and the stress characteristics of pre-stressed anchorage cables in the fractured surface, the rock slope calculated model of a wedge block within the double-slide face was established by using the finite difference software according to the actual slope project combined with indoor model test. The pre-stress loss rule of the anchorage cable and the distribution of axial force and the force-transferring mechanism of the anchorage cable were analyzed during simulation. Also, based on the displacement contour and the safety factor of the calculated results, the quantitative analysis for the reinforcement ef- fect of the rock slope with group pre-stressed anchorage cable was discovered. The results computed by the software conform with the data in the experiment, which can prove the effectiveness and correctness of parameter selection and model building. Keywords group anchorage reinforcement, rock slope, joint fissure, pre-stressed anchorage cable, stress characteristics展开更多
Aiming at prestressed anchor cable frame in the presence of reinforcement landslide problem, through the selection of test points, the paper study and tested soil pressure, frame internal force and prestress losses un...Aiming at prestressed anchor cable frame in the presence of reinforcement landslide problem, through the selection of test points, the paper study and tested soil pressure, frame internal force and prestress losses under prestressed anchor cable frame beam, reveal the law of internal force distribution, and provides a theory basis for the rational design of prestressed anchor cable in landslide.展开更多
By using numerical analysis methods to simulate the deep excavation,a lot of analyses are established on the basis of two-dimensional plane strain,ignoring the fact that foundation pit possesses three dimensions. For ...By using numerical analysis methods to simulate the deep excavation,a lot of analyses are established on the basis of two-dimensional plane strain,ignoring the fact that foundation pit possesses three dimensions. For soil constitutive relation,people always take linear and nonlinear model,without considering the plastic behavior of soil. Using plastic-elastic hardening model to simulate constitutive relation of soil characteristics,the authors carried out mechanical analysis for pit excavation and support. The results show that the analysis for the stress state of pile anchor system is an effective way which provides theoretical basis for calculation of soil displacement.展开更多
文摘The purpose of this paper is to establish confidence in anticipated minimum bond strength for inflatable rock bolts by comparing the bond strength to variable geotechnical conditions using the rock mass rating （RMR） system. To investigate a correlation between these parameters, the minimum bond strength of pull-out tested inflatable rock bolts was compared to the RMR of the rock in which these bolts were placed. Bond strength vs. RMR plots indicate that expected minimum bond strength is positively corre- lated with RMR; however, the correlation is not strong. Cumulative percent graphs indicate that 97~; of pull-out tests result in a minimum bond strength of 3.3 and 1.7 ton/m in RMR/〉 45 and 〈45, respectively. Although lower bond strengths are more commonly encountered in low RMR ground, high bond strengths are possible as well, yielding higher variability in bond strengths in low RMR ground. Bond strength of friction bolts relies on contact between the rock bolt and drill hole. Experience in Nevada indicates that RMR is known to affect both the quality and consistency of drill holes which likely affects bond strength. Drilling and bolting in low RMR ground is more sensitive to drilling and bolting practices, and strategies for maximizing bond strength in these conditions are discussed.
基金Supported by the National Natural Science Foundation of China(50874085)
文摘To research the reinforcement effect of a rock slope with group anchorage cables and the stress characteristics of pre-stressed anchorage cables in the fractured surface, the rock slope calculated model of a wedge block within the double-slide face was established by using the finite difference software according to the actual slope project combined with indoor model test. The pre-stress loss rule of the anchorage cable and the distribution of axial force and the force-transferring mechanism of the anchorage cable were analyzed during simulation. Also, based on the displacement contour and the safety factor of the calculated results, the quantitative analysis for the reinforcement ef- fect of the rock slope with group pre-stressed anchorage cable was discovered. The results computed by the software conform with the data in the experiment, which can prove the effectiveness and correctness of parameter selection and model building. Keywords group anchorage reinforcement, rock slope, joint fissure, pre-stressed anchorage cable, stress characteristics
文摘Aiming at prestressed anchor cable frame in the presence of reinforcement landslide problem, through the selection of test points, the paper study and tested soil pressure, frame internal force and prestress losses under prestressed anchor cable frame beam, reveal the law of internal force distribution, and provides a theory basis for the rational design of prestressed anchor cable in landslide.
文摘By using numerical analysis methods to simulate the deep excavation,a lot of analyses are established on the basis of two-dimensional plane strain,ignoring the fact that foundation pit possesses three dimensions. For soil constitutive relation,people always take linear and nonlinear model,without considering the plastic behavior of soil. Using plastic-elastic hardening model to simulate constitutive relation of soil characteristics,the authors carried out mechanical analysis for pit excavation and support. The results show that the analysis for the stress state of pile anchor system is an effective way which provides theoretical basis for calculation of soil displacement.
