乳化剂后加法制备O/W型乳膏基质及质量考察

目的探讨乳化剂后加法对O/W型乳膏基质质量的影响。方法用乳化剂分相加入法和乳化剂后加法分别制备O/W型乳膏基质,并对稳定性和释放度进行评价。结果乳化剂后加法所制得的乳滴粒径小,分散均匀,质量稳定,释放度高。结论本法可在生产中推广应用。

Synthesis of polyfarnesene based on aqueous free-radical polymerization and molecular dynamics simulation of its properties

Farnesene monomer,obtained through the bio-fermentation,offered a unique long side chain structure that served as an excellent platform for the synthesis of“bottlebrush-like”polymers with exceptional thermal properties.Such polymers had immense potential in the production of polyurethane elastomers and adhesives.Hydroxyl-terminated polyfarnesene(PFD),which was safe,environmentally-friendly and pollution-free,was synthesized with farnesene as the monomer and industrial grade product hydrogen peroxide as the initiator by aqueous free-radical polymerization.

微乳液电纺丝法制备Eu^3+掺杂锆酸镧多孔纤维及其发光性能研究

以LaCl3、ZrClO2·8H2O为原料,无水乙醇为溶剂,采用微乳液静电纺丝法制得烧绿石型的锆酸镧纤维,并引入分相剂石蜡在纤维中构筑多孔结构。采用XRD、SEM和BET研究了纤维的结构和形貌,采用PL光谱测试了Eu^3+掺杂的锆酸镧纤维的发光性能。研究表明,引入分相剂石蜡可以改善纤维中的孔结构,当石蜡用量为4 mL时所制备的锆酸镧纤维物相纯度高,其比表面积为20.77 m^2·g^-1,平均孔径19.3 nm,有较为丰富的孔结构且分布均匀。因此,在该纤维中掺杂Eu^3+后,由于氧离子与稀土离子间的电荷跃迁,以及多孔结构光散射的作用,多孔纤维的发光强度有所提高。

辊道窑快烧铁红釉的研究

通过对辊道窑烧制铁红釉的研制,为铁红釉应用在瓷质釉面砖体系开发新产品提供配方基础。试验对铁红釉中主要析晶体“α-Fe2O3”的析出量,从配方角度进行分析研究,对铁红釉的生产具有参考价值。

Interfacial engineering of heterogeneous molecular electrocatalysts using ionic liquids towards efficient hydrogen peroxide production

Efficient and selective oxygen reduction reaction(ORR)electrocatalysts are critical to realizing decentralized H_(2)O_(2)production and utilization.Here we demonstrate a facile interfacial engineering strategy using a hydrophobic ionic liquid(IL,i.e.,[BMIM][NTF2])to boost the performance of a nitrogen coordinated single atom cobalt catalyst(i.e.),cobalt phthalocyanine(CoPc)supported on carbon nanotubes(CNTs).We find a strong correlation between the ORR performance of CoPc/CNT and the thickness of its IL coatings.Detailed characterization revealed that a higher O_(2)solubility(2.12×10^(−3)mol/L)in the IL compared to aqueous electrolytes provides a local O2 enriched surface layer near active catalytic sites,enhancing the ORR thermodynamics.Further,the hydrophobic IL can efficiently repel the as‐synthesized H_(2)O_(2)molecules from the catalyst surface,preventing their fast decomposition to H_(2)O,resulting in improved H_(2)O_(2)selectivity.Compared to CoPc/CNT without IL coatings,the catalyst with an optimal~8 nm IL coating can deliver a nearly 4 times higher mass specific kinetic current density and 12.5%higher H2O2 selectivity up to 92%.In a two‐electrode electrolyzer test,the optimal catalyst exhibits an enhanced productivity of 3.71 molH2O2 gcat^(–1)h^(–1),and robust stability.This IL‐based interfacial engineering strategy may also be extended to many other electrochemical reactions by carefully tailoring the thickness and hydrophobicity of IL coatings.

Surfactant Distribution in the Clouding of TX114

Distribution of TX114 between coacervate and aqueous phases in clouding of various initial TX114 concentrations was studied. Effects of temperature and salinity （Na2SO4） on the distribution of TX114 concentration were also investigated. Differing from the nonionic surfactant C12E10, the distribution of TX114 is sensitive to the temperature, and it is observed that the TX114 concentration in the aqueous phase （Caq） does not depend on the initial TX114 concentration apparently at 45℃, and the Caq decreases with an increase of NazSO4 concentration. Low initial TX114 concentration in unclouded solutions, high Na2SO4 concentration, and temperature are suggested to control the surfactant loss in large-scale cloud point extraction applications.

Phase separation in solvent extraction of cobalt from acidic sulfate solution using synergistic mixture containing dinonylnaphthalene sulfonic acid and 2-ethylhexyl 4-pyridinecarboxylate ester

Phase separation rate is a critical character in determining the usefulness of a solvent extraction system in hydrometallurgy. A survey of the synergistic mixture containing dinonylnaphthalene sulfonic acid (HDNNS) and 2-ethylhexly 4-pyridinecarboxylate ester (4PC) for the extraction of cobalt from acidic single metal sulfate solution was carried out to suggest how the physicochemical properties and the morphology of the reverse micelles in the loaded organic phase affect the phase separation. The results show that effective parameters affecting the phase separation are the viscosity and the excess water uptake of the loaded organic phase. It is obvious that the specific settling rate (SSR) decreases with the apparent increase of these two parameters. The measurement of small angle X-ray scattering (SAXS) proves that the morphology of the reversed micelles in the loaded organic phase changes evidently with the change of the specific settling rate (SSR).

Flame retardancy and its mechanism of polymers flame retarded by DBDPE/Sb_2O_3

The flammability characterization and thermal composition of polymers flame retarded by decabromodiphenylethane (DBDPE) and antimony trioxide (Sb2O3) were studied by cone calorimeter and thermogravimetry (TG). The results show that ABS/DBDPE/Sb2O3 has the similar flammability parameters and thermal composition curves to ABS/DBDPO/Sb2O3. It suggests that DBDPE/Sb2O3 has the similar flame retardant behavior to DBDPO/Sb2O3. The heat release rate (HRR) and the effect heat combustion (EHC) curves of polymers flame retarded by DBDPE/Sb2O3 all decrease, but the mass loss rate (MLR) curve slightly increase. It shows that the decrease of HRR is not due to the increase of char formation ratio but the generation of incombustible gases. The major flame retardant mechanism of DBDPE/Sb2O3 is gas phase flame retardant mechanism. Increasing content of Sb2O3 in DBDPE/Sb2O3 can improve the flame retardant property and thermal stability of acrylonitrile butadiene styrene. Sb2O3 has a good synergistic effect with DBDPE.

Numerical Modeling of the Performance of R22 and R290 in Adiabatic Capillary Tubes Considering Metastable Two-Phase Region——Flow Characteristics and Parametric Analysis of R22 and R290

Characteristics of R22 and its new alternative refrigerant R200 flowing through adiabatic capillary tubes are investigated based on the homogeneous model. Extensive flow variables along tube length such as pressure, temperature, viscosity, velocity. Reynolds number, friction factor and vapor quality etc are compared between the two fluids under the same operating condition. Two cases are considered, namely, either the same tube length or the same mass flow rate as inlet condition. The results show that the mass flow rate in the capillary tube of R290 is 40% lower than that of R22 due to the differences of physical properties between the two fluids. Further. a parametric analysis is performed and it appears that effects of geometric and thermodynamic parameters on mass flow rate of R290 are weaker than that of R22. When the condensing temperature is increased from 40℃ to 50℃ C. the mass flow rate for R22 is increased by 16%. while the increasing rate for R290 is 13%.

Recent advances and perspectives in cobalt‐based heterogeneous catalysts for photocatalytic water splitting,CO_(2) reduction,and N_(2) fixation

Solar‐driven conversion of carbon dioxide,water and nitrogen into high value‐added fuels(e.g.H_(2),CO,CH_(4),CH_(3)OH,NH_(3) and so on)is regarded as an environmental‐friendly and ideal route for relieving the greenhouse gas effect and countering energy crisis,which is an attractive and challenging topic.Hence,various types of photocatalysts have been developed successively to meet the requirements of these photocatalysis.Among them,cobalt‐based heterogeneous catalysts emerge as one of the most promising photocatalysts that open up alluring vistas in the field of solar‐to‐fuels conversion,which can effectively enhance photocatalytic efficiency by extending light absorption range,promoting charge separation,providing active sites,and lowering reaction barrier.In this review,we first present the working principles of cobalt‐based heterogeneous catalysts for photocatalytic water splitting,CO_(2) reduction,and N_(2) fixation.Second,five efficient strategies including surface modification,morphology modulation,crystallinity controlling,crystal engineering and doping,are discussed for improving the photocatalytic performance with different types cobalt‐based catalysts(cobalt nanoparticles and single atom,oxides,sulfides,phosphides,MOFs,COFs,LDHs,carbide,and nitrides).Third,we outline the applications for the state‐of‐the‐art photocatalytic CO_(2) reduction and water splitting,and nitrogen fixation over cobalt‐based heterogeneous catalysts.Finally,the central challenges and possible improvements of cobalt‐based photocatalysis in the future are presented.The purpose of this review is to summarize the past experience and lessons,and provide reference for the further development of cobalt‐based photocatalysis technology.

Separation of Quercentin by Pre-dispersed Solvent Extraction

Pre-dispersed solvent extraction (PDSE) was used to extract quercentin from its diluted solution. The influences of temperature, phase volume ratio (PVR), concentration of sodium Dodecyl benzene sulphonate and pH value etc. on the extraction efficiency were examined. It is found that, compared with traditional extraction techniques under the same condition, a higher extraction productivity can be obtained by PDSE. The stability of colloidal liquid aphrons plays an important role in this process. In a certain scope, the extraction efficiency increases with PVR. Excessive amount of solvent is not much helpful. A new analytical method by using ultraviolet spectrometer to determine the concentration of quercentin is established.

Effects of Additives and Coagulant Temperature on Fabrication of High Performance PVDF/Pluronic F127 Blend Hollow Fiber Membranes via Nonsolvent Induced Phase Separation

Poly（vinylidene fluoride） （PVDF） has become one of the most popular materials for membrane preparation via nonsolvent induced phase separation （NIPS） process. In this study, an amphiphilic block copolymer, Pluronic F127, has been used as both a pore-former and a surface-modifier in the fabrication of PVDF hollow fibermembranes to enhance the membrane permeability and hydrophilicity. The effects of 2nd additive and coagulant temperature on the formation of PVDF/Pluronic F 127 membranes have also been investigated. The as-spun hollow fibers were characterized in terms of cross-sectional morphology, pure water permeation （PWP）, relative molecular mass cut-off （MWCO）, membrane chemistry, and hydrolphilicity. It was obsered that the addition of Pluronic F 127 significantly increased the PWP of as-spun fibers, while the membrane contact angle was reduced. However, the size of macrovoids in the membranes was undesirably large. The addition of a 2nd additive, including lithium chloride （LiC1） and water, or an increase in coagulant temperature was found to effectively suppress the macrovoid for- mation in the Pluronic-containing membranes. In addition, the use of LiC1 as a 2nd additive also further enhanced the PWP and hydrophilicity of the membranes, while the surface pore size became smaller. PVDF hollow fiber with a PWP as high as 2330 L·m-2·h-1·MPa-1, a MWCO of 53000 and＇a contact angle of 71 o was successfully fabricated with 3% （by mass） of Pluronic F127 and 3% （by mass） of LiC1 at a coagulant temperature of 25 ℃, which shows better performance as compared with most of PVDF hollow fiber membranes made by NIPS method.

Phase Separation and Microstructure of Mixed Surfactants Solution Containing Cationic Geminis and Traditional Anionic Surfactant

The properties of aqueous two-phase system (ATPS) of mixed solution containing gemini cationic surfactant trimethylene-1,3-bis(dodecyldimethyl ammonium) bromide (12-3-12, 2Br-) and traditional anionic surfactant sodium dodecyl sulfate (SDS) with or without added salt have been studied. An ATPS is formed in a narrow region of the ternary phase diagram different from that of traditional aqueous cationic-anionic surfactant systems. In ATPS region, the lowest total concentration of surfactants varies with the mixing ratio of geminis to SDS. Photographs obtained from freeze-etching, negative-staining and transmission electron microscopy show that the microstructures of two phases are different from each other. Micelles and vesicles can coexist in a single phase. The addition of salts can change the phase diagram of ATPS. Furthermore, the added salts promote the aggregation of rod-like micelles to form coarse network structure that increase the viscosity of solutions. The negative ions of the added salts are the determining factor.

Structural and interfacial engineering of well‐defined metal‐organic ensembles for electrocatalytic carbon dioxide reduction

Electrochemical carbon dioxide reduction(CO_(2)RR)has been generally regarded as green technologies that can convert renewable energy such as sunlight and wind into fuels and valuable chemicals.However,the large‐scale implementation of CO_(2)RR is severely hindered by the lack of high‐performance CO_(2)RR electrocatalysts.Heterogeneous molecular catalysts and metal‐organic framework with well‐defined structure and high tunability of the metal centers and ligands show great promise for CO_(2)RR in terms of both fundamental understanding and practical application.Here,structural and interfacial engineering of these well‐defined metal‐organic ensembles is summarized.This review starts from the fundamental electrochemistry of CO_(2)RR and its evaluation criteria,and then moves to the heterogeneous molecular catalysts and metal‐organic framework with emphasis on the engineering of metal centers and ligands,their interaction with supports,as well as in situ reconstruction of metal‐organic ensembles.Summary and outlook are present in the end,with the hope to inspire and provoke more genuine thinking on the design and fabrication of efficient CO_(2)RR electrocatalysts.

Disproportionation of Toluene by Modified ZSM-5 Zeolite Catalysts with High Shape-selectivity Prepared Using Chemical Liquid Deposition with Tetraethyl Orthosilicate

Shape-selective catalysts for the disproportionation of toluene were prepared by the modification of the cylinder-shaped ZSM-5 zeolite extrudates with chemical liquid deposition with TEOS （tetraethyl orthosilicate）.Various parameters for preparing catalysts were changed to investigate the suitable conditions.The resulting cata-lysts were tested in a pressured fixed bed reactor and characterized by SEM （scanning electron microscopy）.The conversion of toluene and para-xylene selectivity were influenced remarkably by the n（SiO2）/n（Al2O3） ratio of ZSM-5 zeolite,the type and amount of deposition agent,acid and solvent used,and the time and cycle of deposition treatment.TEOS was proved to be a more efficient agent than the conventional polysiloxanes when the deposition amount was low.The catalyst prepared at the suitable conditions exhibited a high para-xylene selectivity of 91.1% with considerable high conversion of 25.6%.SEM analyses confirmed the formation of a layer of amorphous silica on the external surface of ZSM-5 zeolie crystals,which was responsible for the highly enhanced shape-selectivity.

Novel nanofiltration membranes with tunable permselectivity by polymer mediated phase separation in polyamide selective layer

Microstructure in selective layer has played a decisive role in permselectivity of nanofiltration(NF) membranes,and nanomaterials were well-known additives that had been applied to mediate the microstructure and permeability of polyamide NF membranes. However, nanoadditives generally displayed a poor dispersion in membranes or in fabrication process. To solve this problem, we showed an interesting concept that novel NF membranes with hybrid selective layer consisting of flexible polyisobutylene(PIB) and rigid polyamide could be fabricated from well-defined interfacial polymerization. The hydrophobic polymer mediated phase separation and microdomains formation in polyamide layer were found. The immiscibility between the rigid polyamide and flexible PIB as well as the resultant interface effect was interpreted as the reason for the polymer enhanced permselectivity, which was similar with the well-known thin film nanocomposite(TFN) membranes that nanoparticles incorporated contributed significantly to membrane permeability and rejection performance.Our results have demonstrated that novel NF membranes with enhanced performance can be prepared from immiscible polymers, which is a new area that has not been extensively studied before.

Enantiomeric separation of phenylsuccinic acid by cyclodextrin-modified reversed phase high-performance liquid chromatography

The chiral separation of phenylsuccinic acid(PSA)was studied by reversed phase high-performance liquid chromatography(RP-HPLC)with cyclodextrins(CDs)as chiral mobile phase additives.The effects of types of CDs,concentration of hydroxypropyl-β-cyclodextrin(HP-β-CD),percentage of organic modifier,pH value and column temperature on enantioselective separation were investigated.The quantification property of the developed RP-HPLC method was examined.The chiral recognition mechanism of PSA was also discussed.The results show that a baseline separation of PSA enantiomers is achieved on a Lichrospher C18 column(4.6 mm(inner diameter)×250 mm,5μm)with HP-β-CD as chiral mobile phase additive.The capacity factors of R-PSA and S-PSA are 3.94 and 4.80,respectively.The separation factor and resolution are respectively 1.22 and 8.03.The mobile phase is a mixture of acetonitrile and deionized water(20-80,volume ratio)containing 10 mmol/L HP-β-CD and 0.05% trifluoroacetic acid(pH 2.5,adjusted with triethylamine)with a flow rate of 1.0 mL/min.The ultraviolet(UV)detector is set at 254 nm.The likely roles are inclusion interaction,induction and hydrogen bonding between HP-β-CD and PSA enantiomers.

3D-QSAR and action mechanism of potential dual inhibitors towards AP-1 and NF-κB

Three-dimensional quantitative structure-activity relationship （3D-QSAR） and docking studies of a series of novel dioxopyrrolinyl-amino-pyrimidine derivatives, which are potential dual inhibitors mediating a transcriptional activation towards protein-1 （AP-1） and nuclear factor kappa B （NF-κB）, have been carried out. The QS, AR models established by comparative molecular field analysis （CoMFA） and comparative molecular similarity index analysis （CoMSIA） show a good predictive ability with cross-validated coefficients q2 of 0.644 and 0.636, respectively. The docking result shows that there are quite lower average values of the flexible and rigid energy scores on the selected binding sites, meanwhile, it further shows that the binding sites just fall on the joint regions between AP-1 （and NF-κB） and DNA. The reason that these analogues have inhibition function towards AP-I and NF-κB is that their existence on these joint regions can effectively prevent free AP-I and NF-κB from binding to DNA. These results can offer a valuable theoretical reference to the pharmaceutical molecular design as well as the action mechanism analysis.

Recent Advances in Multifunctional Capsule Catalysts in Heterogeneous Catalysis

Capsule catalysts composed of pre-shaped core catalysts and layer zeolites have been widely used in the tandem reactions where multiple continuous reactions are combined into one process. They show excellent catalytic performance in heterogeneous catalysis, including the direct synthesis of middle isoparaflins or dimethyl ether from syngas, as compared to the conventional hybrid catalysts. The present review highlights the recent development in the design of capsule catalysts and their catalytic applications in heterogeneous catalysis. The capsule catalyst preparation methods are introduced in detail, such as hydrothermal synthe- sis method, dual-layer method, physically adhesive method and single crystal crystallization method. Purthermore, several new applications of capsule catalysts in heterogeneous cat- alytic processes are presented such as in the direct synthesis of liquefied petroleum gas from syngas, the direct synthesis of para-xylene from syngas and methane dehydroaromatization. In addition, the development in the design of multifunctional capsule catalysts is discussed, which makes the capsule catalyst not just a simple combination of two dill）rent catalysts, but has some special functions such as changing the surface hydrophobic or acid properties of the core catalysts. Finally, the future perspectives of the design and applications of capsule catalysts in heterogeneous catalysis are provided.

Investigation of condition-induced bubble size and distribution in electroflotation using a high-speed camera

In the flotation process, bubble is a key factor in studying bubble-particle interaction and fine particle flo- tation. Knowledge on size distribution of bubbles in a flotation system is highly important. In this study, bubble distributions in different reagent concentrations, electrolyte concentrations, cathode apertures, and current densities in electroflotation are determined using a high-speed camera. Average bubble sizes under different conditions are calculated using Image-Pro@ Plus （Media Cybernetics@, MD, USA） and SigmaScan@ Pro （Systat Software, CA, USA） software. Results indicate that the average sizes of bubbles, which were generated through 38, 50, 74, 150, 250, 420, and 1000 μm cathode apertures, are 20.2, 29.5, 44.6, 59.2, 68.7, 78.5, and 88.8 μm, respectively. The optimal current density in electroflotation is 20 A/m2. Reagent and electrolyte concentrations, current density, and cathode aperture are important factors in controlling bubble size and nucleation. These factors also contribute to the control of fine- Particle flotation.