This paper proposes a family of PWM modulation strategies for boostfull-bridge (FB) converters. The modulation strategies can be classified into two kinds according tothe turn-on sequence of the diagonal switches. The...This paper proposes a family of PWM modulation strategies for boostfull-bridge (FB) converters. The modulation strategies can be classified into two kinds according tothe turn-on sequence of the diagonal switches. The concept of leading switches and lagging switchesis introduced to realize soft-switching. According to the soft-switching realized by the leadingswitches and the lagging switches, two kinds of soft-switching techniques for PWM boost FBconverters yield: zero-current-switching (ZCS) and zero-current and zero-voltage-switching (ZCZVS).Simulation results verify the analysis.展开更多
A coaxial mixer meeting the actual demand of a system with high and variable viscosity is investigated. It has an outer wall-scraping frame and a double inner impeller consisting of a four-pitched-blade turbine and Ru...A coaxial mixer meeting the actual demand of a system with high and variable viscosity is investigated. It has an outer wall-scraping frame and a double inner impeller consisting of a four-pitched-blade turbine and Rushton turbine. The power consumption and flow field characteristics of the coaxial mixer in laminar and transitional flow are simulated numerically, and then the distribution of velocity field, shear rate and mass flow rate are analyzed. The simulation results indicate that the outer frame has little effect on the power consumption of the double inner impeller whether in laminar or transitional flow, whereas the inner combined impeller has a great effect on the power consumption of the outer frame. Compared with the single rotation mode, the power consumption of the outer frame will decrease in co-rotation mode and increase in counter-rotation mode. The velocity, shear rate and mass flow rate are relatively high near the inner impeller in all operating modes, and only under double-shaft agitation will the mixing performance near the free surface be improved.In addition, these distributions in the co-rotation and counter-rotation modes show little difference, but the co-rotation mode is recommended for the advantage of low power consumption.展开更多
In order to rescue a trapped miner and clean out roadways quickly in a high gas mine shaft after a mining mishap, a special portable cold-cutting equipment is needed, the main technology parameters were calculated acc...In order to rescue a trapped miner and clean out roadways quickly in a high gas mine shaft after a mining mishap, a special portable cold-cutting equipment is needed, the main technology parameters were calculated according to the advanced cold-cutting technology of high pressure abrasive water jet and the portable mixed abrasive water jet equipment （PAWE） was designed to meet the needs of emergency rescue in high gas mine shafts. Tested the PAWE in a high gas environment, and the result shows that the maximum cutting depth of solid iron pipe is 18 mm and the recoilforce of the sprayer is 28.9 N under the conditions that actual cutting pressure is 29 MPa, starting target distance is 10 ram, cutting speed is 180 mm/min and concentration of abrasive is 32%. The course of the experiment in the high gas environment was smooth and continuous, without any explosion. The PAWE is easy to move and operate, but the nozzle which was worn badly in the sprayer should be changed every 8 minutes.展开更多
In order to control the maximum tangential velocity V?m(m/s)of the turbulent rotational air flow and the collection efficiencyηc(%)using the fly ash of the mean diameter X R50=5.57?m,two secondary jet nozzles were in...In order to control the maximum tangential velocity V?m(m/s)of the turbulent rotational air flow and the collection efficiencyηc(%)using the fly ash of the mean diameter X R50=5.57?m,two secondary jet nozzles were installed to the body of the axial flow cyclone dust collector with the body diameter D1=99mm.Then in order to estimate V?m(m/s),the conservation theory of the angular momentum flux with Ogawa combined vortex model was applied.The comparisons of the estimated results of V?m(m/s)with the measured results by the cylindrical Pitot-tube were shown in good agreement.And also the estimated collection efficienciesηcth(%)basing upon the cut-size Xc(?m)which was calculated by using the estimated V?m(m/s)and also the particle size distribution R(Xp)were shown a little higher values than the experimental results due to the re-entrainment of the collected dust.The best method for adjustment ofηc(%)related to the contribution of the secondary jet flow is principally to apply the centrifugal effect?c(1).Above stated results are described in detail.展开更多
文摘This paper proposes a family of PWM modulation strategies for boostfull-bridge (FB) converters. The modulation strategies can be classified into two kinds according tothe turn-on sequence of the diagonal switches. The concept of leading switches and lagging switchesis introduced to realize soft-switching. According to the soft-switching realized by the leadingswitches and the lagging switches, two kinds of soft-switching techniques for PWM boost FBconverters yield: zero-current-switching (ZCS) and zero-current and zero-voltage-switching (ZCZVS).Simulation results verify the analysis.
基金Supported by the Fundamental Research Funds for the Central Universities(2012QNA4018)the National Natural Science foundation of China(21206144)the Program for Zhejiang Leading Team of S&T Innovation(2011R50005)
文摘A coaxial mixer meeting the actual demand of a system with high and variable viscosity is investigated. It has an outer wall-scraping frame and a double inner impeller consisting of a four-pitched-blade turbine and Rushton turbine. The power consumption and flow field characteristics of the coaxial mixer in laminar and transitional flow are simulated numerically, and then the distribution of velocity field, shear rate and mass flow rate are analyzed. The simulation results indicate that the outer frame has little effect on the power consumption of the double inner impeller whether in laminar or transitional flow, whereas the inner combined impeller has a great effect on the power consumption of the outer frame. Compared with the single rotation mode, the power consumption of the outer frame will decrease in co-rotation mode and increase in counter-rotation mode. The velocity, shear rate and mass flow rate are relatively high near the inner impeller in all operating modes, and only under double-shaft agitation will the mixing performance near the free surface be improved.In addition, these distributions in the co-rotation and counter-rotation modes show little difference, but the co-rotation mode is recommended for the advantage of low power consumption.
文摘In order to rescue a trapped miner and clean out roadways quickly in a high gas mine shaft after a mining mishap, a special portable cold-cutting equipment is needed, the main technology parameters were calculated according to the advanced cold-cutting technology of high pressure abrasive water jet and the portable mixed abrasive water jet equipment （PAWE） was designed to meet the needs of emergency rescue in high gas mine shafts. Tested the PAWE in a high gas environment, and the result shows that the maximum cutting depth of solid iron pipe is 18 mm and the recoilforce of the sprayer is 28.9 N under the conditions that actual cutting pressure is 29 MPa, starting target distance is 10 ram, cutting speed is 180 mm/min and concentration of abrasive is 32%. The course of the experiment in the high gas environment was smooth and continuous, without any explosion. The PAWE is easy to move and operate, but the nozzle which was worn badly in the sprayer should be changed every 8 minutes.
文摘In order to control the maximum tangential velocity V?m(m/s)of the turbulent rotational air flow and the collection efficiencyηc(%)using the fly ash of the mean diameter X R50=5.57?m,two secondary jet nozzles were installed to the body of the axial flow cyclone dust collector with the body diameter D1=99mm.Then in order to estimate V?m(m/s),the conservation theory of the angular momentum flux with Ogawa combined vortex model was applied.The comparisons of the estimated results of V?m(m/s)with the measured results by the cylindrical Pitot-tube were shown in good agreement.And also the estimated collection efficienciesηcth(%)basing upon the cut-size Xc(?m)which was calculated by using the estimated V?m(m/s)and also the particle size distribution R(Xp)were shown a little higher values than the experimental results due to the re-entrainment of the collected dust.The best method for adjustment ofηc(%)related to the contribution of the secondary jet flow is principally to apply the centrifugal effect?c(1).Above stated results are described in detail.
