A new contact model of traveling wave ultrasonic motor （TWUSM） with a visco-elastic stator frictional layer was presented. In this model, the initial boundaries were revised, and the rotor revolution speed could he ...A new contact model of traveling wave ultrasonic motor （TWUSM） with a visco-elastic stator frictional layer was presented. In this model, the initial boundaries were revised, and the rotor revolution speed could he calculated iteratively. This model was compared with compliant slider and rigid stator model. The results of motor characteristics simulations showed that the motors based on this model would gain bigger stall torque. Then the friction and wear characteristics of two models were analyzed. The motors based on this model had lower coefficient of friction and better wear resistance.展开更多
According to the critical size ratio for the characteristic particle size to film thickness between grinding wheel and work, the machining mechanisms in abrasive jet precision finishing with grinding wheel as restrain...According to the critical size ratio for the characteristic particle size to film thickness between grinding wheel and work, the machining mechanisms in abrasive jet precision finishing with grinding wheel as restraint can be categorized into four states, namely, two-body lapping, three-body polishing, abrasive jet machining and fluid hydrodynamic shear stress machining. The critical transition condition of two-body lapping to three-body polishing was analyzed. The single abrasive material removal models of two-body lapping, three-body polishing, abrasive jet finishing and fluid hydrodynamic shear stress machining were proposed. Experiments were performed in the refited plane grinding machine for theoretical modes verification. It was found that experimental results agreed with academic modes and the modes validity was verified.展开更多
To increase the machine accuracy by improving the stiffness of bearings,a preload was applied to bearings.A variable preload technology was necessary to perform machining processes in both low and high speed regions.A...To increase the machine accuracy by improving the stiffness of bearings,a preload was applied to bearings.A variable preload technology was necessary to perform machining processes in both low and high speed regions.An automatic variable preload device was fabricated using an eccentric mass.By installing the fabricated device on a spindle,the effect of the automatic variable preload device on the performance of the spindle was analyzed.In the results of the vibration measurement of the spindle,the vibration is increased by 20%-37% according to measurement points at the maximum rotation speed of 5 000 r/min.And,in the results of the noise measurement of the spindle,the spindle rotation speed is increased by about 1.9% and 1.5% at the front and side of the spindle,respectively.Based on the results of this analysis,an improved method that reduces such effects on the performance of the spindle is proposed.展开更多
This paper presents the work implemented in designing, fabricating and operating a model of a cheap hydraulic DDM （deep drawing machine）, which is currently utilized in the manufacturing processes lab in the IED （I...This paper presents the work implemented in designing, fabricating and operating a model of a cheap hydraulic DDM （deep drawing machine）, which is currently utilized in the manufacturing processes lab in the IED （Industrial Engineering Department） at An-Najah National University. The machine is used to conduct different experiments related to the deep drawing process. This work was implemented in three stages： the first was the design stage, in which all design calculations of the DDM elements were completed based on the specifications of the product （cup） to be drawn; the second was the construction stage, in which the DDM elements were fabricated and assembled at the engineering workshops of the university; the last was the operating and experimentation stage, in which the DDM was tested by conducting different experiments. The experience gained from designing and constructing such a mechanical lab equipment was found to be successful in terms of obtaining practical results that agree with those available in literature, cost-effective relative to the cost of a similar purchased equipment, as well as enhancing students＇ abilities in understanding the deep drawing process in particular and machine elements design concepts in general.展开更多
基金Sponsored by the Natural Sciences Foundation of China (Grant No 50575055)the National 973 Key Development Project in Fundamental Science Research (Grant No2007CB607602)
文摘A new contact model of traveling wave ultrasonic motor （TWUSM） with a visco-elastic stator frictional layer was presented. In this model, the initial boundaries were revised, and the rotor revolution speed could he calculated iteratively. This model was compared with compliant slider and rigid stator model. The results of motor characteristics simulations showed that the motors based on this model would gain bigger stall torque. Then the friction and wear characteristics of two models were analyzed. The motors based on this model had lower coefficient of friction and better wear resistance.
基金Sponsored by the National Natural Science Foundation of China (Grant No 50475052)the Specialized Research Fund for the Doctoral Program of Higher Education (Grant No 20040145001)
文摘According to the critical size ratio for the characteristic particle size to film thickness between grinding wheel and work, the machining mechanisms in abrasive jet precision finishing with grinding wheel as restraint can be categorized into four states, namely, two-body lapping, three-body polishing, abrasive jet machining and fluid hydrodynamic shear stress machining. The critical transition condition of two-body lapping to three-body polishing was analyzed. The single abrasive material removal models of two-body lapping, three-body polishing, abrasive jet finishing and fluid hydrodynamic shear stress machining were proposed. Experiments were performed in the refited plane grinding machine for theoretical modes verification. It was found that experimental results agreed with academic modes and the modes validity was verified.
基金Project(2011-0027035) supported by the Basic Science Research Program through the National Research Foundation of Korea (NRF)funded by the Ministry of Education,Science and Technology,Korea
文摘To increase the machine accuracy by improving the stiffness of bearings,a preload was applied to bearings.A variable preload technology was necessary to perform machining processes in both low and high speed regions.An automatic variable preload device was fabricated using an eccentric mass.By installing the fabricated device on a spindle,the effect of the automatic variable preload device on the performance of the spindle was analyzed.In the results of the vibration measurement of the spindle,the vibration is increased by 20%-37% according to measurement points at the maximum rotation speed of 5 000 r/min.And,in the results of the noise measurement of the spindle,the spindle rotation speed is increased by about 1.9% and 1.5% at the front and side of the spindle,respectively.Based on the results of this analysis,an improved method that reduces such effects on the performance of the spindle is proposed.
文摘This paper presents the work implemented in designing, fabricating and operating a model of a cheap hydraulic DDM （deep drawing machine）, which is currently utilized in the manufacturing processes lab in the IED （Industrial Engineering Department） at An-Najah National University. The machine is used to conduct different experiments related to the deep drawing process. This work was implemented in three stages： the first was the design stage, in which all design calculations of the DDM elements were completed based on the specifications of the product （cup） to be drawn; the second was the construction stage, in which the DDM elements were fabricated and assembled at the engineering workshops of the university; the last was the operating and experimentation stage, in which the DDM was tested by conducting different experiments. The experience gained from designing and constructing such a mechanical lab equipment was found to be successful in terms of obtaining practical results that agree with those available in literature, cost-effective relative to the cost of a similar purchased equipment, as well as enhancing students＇ abilities in understanding the deep drawing process in particular and machine elements design concepts in general.
