Logging residue can be defined as any form of wood, which under the highest stage of technological development could be used in manufacturing but is left in the forest during logging. Lumber production from logging re...Logging residue can be defined as any form of wood, which under the highest stage of technological development could be used in manufacturing but is left in the forest during logging. Lumber production from logging residues of a previous logging activity by a timber firm was undertaken with the objective of determining the suitability of utilizing buttressed-stumps as raw material for the timber industry. A horizontal mobile bandsaw machine was used to process the buttressed-stumps into lumber. The machine was characterized by a thin-kerr sawing technology （kerf-width 1.6 mm） compared to the conventional bandsaw machines of kerr-widths ranging from 3.0-4.5 mm. Lumber value and volume yields, fuel consumption rate, frequency of tool replacement and lumber production rate were assessed. Results indicated that there is the potential to increase timber production from logging residues by utilizing buttressed-stumps. Lumber value and volume yields of eight timber species investigated in this study ranged from 5%-31% and 34%-54% respectively. Fuel consumption rate which increased with increasing wood density, ranged from 5-14.5 liters/m3 of lumber produced. Frequency of saw replacement increased with increasing wood density. The number of saws required to produce one cubic meter of lumber, ranged from 1 to 7. Lumber production rate ranged from 0.10-0.38 m3/hour, increasing with decreasing wood density.展开更多
A SOFC （solid oxide fuel cell） cycle running on natural gas was integrated with a ST （steam turbine） cycle. The fuel is desulfurized and pre-reformed before entering the SOFC. A burner was used to combust the rema...A SOFC （solid oxide fuel cell） cycle running on natural gas was integrated with a ST （steam turbine） cycle. The fuel is desulfurized and pre-reformed before entering the SOFC. A burner was used to combust the remaining fuel after the SOFC stacks. The off-gases from the burner were used to produce steam in a HRSG （heat recovery steam generator）. The bottoming steam cycle was modeled with two configurations： （1） a simple single pressure level and （2） a dual pressure level with both a reheat and a pre-heater. The SOFC stacks in the present SOFC-ST hybrid cycles were not pressurized. The dual pressure configuration steam cycle combined with SOFC cycle （SOFC-ST） was new and has not been studied previously. In each of the configuration, a hybrid recuperator was used to recovery the remaining energy of the off-gases after the HRSG. Thus, four different plants system setups were compared to each other to reveal the most superior concept with respect to plant efficiency and power. It was found that in order to increase the plant efficiency considerably, it was enough to use a single pressure with a hybrid recuperator instead of a dual pressure Rankine cycle.展开更多
文摘Logging residue can be defined as any form of wood, which under the highest stage of technological development could be used in manufacturing but is left in the forest during logging. Lumber production from logging residues of a previous logging activity by a timber firm was undertaken with the objective of determining the suitability of utilizing buttressed-stumps as raw material for the timber industry. A horizontal mobile bandsaw machine was used to process the buttressed-stumps into lumber. The machine was characterized by a thin-kerr sawing technology （kerf-width 1.6 mm） compared to the conventional bandsaw machines of kerr-widths ranging from 3.0-4.5 mm. Lumber value and volume yields, fuel consumption rate, frequency of tool replacement and lumber production rate were assessed. Results indicated that there is the potential to increase timber production from logging residues by utilizing buttressed-stumps. Lumber value and volume yields of eight timber species investigated in this study ranged from 5%-31% and 34%-54% respectively. Fuel consumption rate which increased with increasing wood density, ranged from 5-14.5 liters/m3 of lumber produced. Frequency of saw replacement increased with increasing wood density. The number of saws required to produce one cubic meter of lumber, ranged from 1 to 7. Lumber production rate ranged from 0.10-0.38 m3/hour, increasing with decreasing wood density.
文摘A SOFC （solid oxide fuel cell） cycle running on natural gas was integrated with a ST （steam turbine） cycle. The fuel is desulfurized and pre-reformed before entering the SOFC. A burner was used to combust the remaining fuel after the SOFC stacks. The off-gases from the burner were used to produce steam in a HRSG （heat recovery steam generator）. The bottoming steam cycle was modeled with two configurations： （1） a simple single pressure level and （2） a dual pressure level with both a reheat and a pre-heater. The SOFC stacks in the present SOFC-ST hybrid cycles were not pressurized. The dual pressure configuration steam cycle combined with SOFC cycle （SOFC-ST） was new and has not been studied previously. In each of the configuration, a hybrid recuperator was used to recovery the remaining energy of the off-gases after the HRSG. Thus, four different plants system setups were compared to each other to reveal the most superior concept with respect to plant efficiency and power. It was found that in order to increase the plant efficiency considerably, it was enough to use a single pressure with a hybrid recuperator instead of a dual pressure Rankine cycle.
