振动环境试验力参数测量技术研究

目前美欧航天界在航天器振动环境试验中,已将采用力限制控制技术形成一项技术标准,主要目的是减少试验中造成过试验的几率,我国航天部门也开始针对此项技术进行应用研究。在力限制控制技术中如何保证力参数测量的实施和准确性是进行此项研究的关键技术之一,文中主要介绍在此项研究中多分量力参数测量的实施过程,及测量的数据结果和数据分析,目的是对振动试验环境使用测力单元进行力参数测量技术进行一次总结,为进一步开展力参数测量技术的研究积累经验。

Cross-section distortion and springback characteristics of double-cavity aluminum profile in force controlled stretch-bending

3D elastic-plastic FE model for simulating the force controlled stretch-bending process of double-cavity aluminum profile was established using hybrid explicit−implicit solvent method.Considering the computational accuracy and efficiency,the optimal choices of numerical parameters and algorithms in FE modelling were determined.The formation mechanisms of cross-section distortion and springback were revealed.The effects of pre-stretching,post-stretching,friction,and the addition of internal fillers on forming quality were investigated.The results show that the stress state of profile in stretch-bending is uniaxial with only a circumferential stress.The stress distribution along the length direction of profile is non-uniform and the maximum tensile stress is located at a certain distance away from the center of profile.As aluminum profile is gradually attached to bending die,the distribution characteristic of cross-section distortion along the length direction of profile changes from V-shape to W-shape.After unloading the forming tools,cross-section distortion decreases obviously due to the stress relaxation,with a maximum distortion difference of 13%before and after unloading.As pre-stretching and post-stretching forces increase,cross-section distortion increases gradually,while springback first decreases and then remains unchanged.With increasing friction between bending die and profile,cross-section distortion slightly decreases,while springback increases.Cross-section distortion decreases by 83%with adding PVC fillers into the cavities of profile,while springback increases by 192.2%.

Flexural behaviors of double-reinforced ECC beams

In order to investigate the flexural behaviors of engineered cementitious composites （ECC）, theoretical and experimental researches are done on flexural doublereinforced ECC beams. Based on the assumption of the plane section remaining plane in bending and simplified constitutive models of materials, the calculation methods of load carrying capacities for different critical stages are obtained. Then, these calculation methods are demonstrated by comparing the test results with the calculation results. Finally, based on the proposed theoretical formulae, the effects of the compression strength, compression strain and tension strength of ECC, and the reinforcement ratio on the flexural behaviors of double-reinforced ECC beams are analyzed. The calculated and measured results are in good agreement, which indicates that the theoretical model can be used to predict the momentcurvature response of steel reinforced ECC beams. And the results of parametric studies show that the increase in the compression strength of ECC can greatly improve the flexural performance of beams; the increase in the ultimate compression strain can significantly improve the ultimate curvature and ductility, but has little effect on the load bearing capacity of beams. little effect on the flexural The tensile strength of ECC has behaviors of ECC beams. The increase in the steel reinforcement ratio can lead to significant improvement of the load bearing capacity and the stiffness of beams, but a degradation of the ductility of beams. The theoretical model and parameter analysis results in this paper are instructive for the design of steel reinforced ECC beams.

Thermogravimetric characteristics and different kinetic models for medical waste composition containing polyvinyl chloride-transfusion tube

Thermogravimetric study of medical transfusion tube （MTT） waste containing polyvinyl chloride （PVC） was carried out using the thermogravimetric analyser （TGA） with N2, at different heating rates of 5, 10, 20, 30, 50 ℃/min. The purpose is to obtain pyrolysis characteristics and kinetic parameters of medical waste. The experimental results indicate that the pyrolysis behavior of the MTT sample is in agreement with its main ingredient of PVC, appearing two stair stepping stages. The influence of the additives in MTT on pyrolysis behavior was also revealed, which could improve MTT pyrolysis at lower temperature in the first stage, and cause obvious unsmoothness and asymmetry of the second DTG peak. Four n-order kinetic models of Coats-Redfern, Ozawa, Kissinger and Freeman-carroll were used to get the kinetic parameters. Furthermore, a novel ＂two-step four-reaction model＂ was established to simulate the whole continuous process. The different methods and the kinetic parameters thus obtained were discussed and compared with each other in literatures. The reasons of deviation among kinetic values were tried to be elucidated. The new established model could more satisfactorily describe the pyrolysis process of MTT, being more mechanistic and conveniently serving for the engineering.

Stress redistribution of simply supported reinforced concrete beams under fire conditions

This study presents experimental and numerical investigations of simply supported steel reinforced concrete(RC)beams under fire.The temperature field of cross sections,the vertical deflection at mid-span,and specifically the axial expansion displacement at beam-ends were measured during the fire tests.A novel finite element(FE)model of a RC beam under fire was developed,in which the water loss in the heat transfer analysis and the concrete transient strain in the mechanical analysis were considered.Based on the validated FE model proposed in this study,parametric studies were conducted to investigate the effects of the beam type,the protective layer thickness,and the load ratio on the thermal and mechanical behavior of simply supported RC beams.It was found that greater fire resistance and fire performance of girder beams in comparison to secondary beams contributed to the non-structural reinforcements,which effectively compensated for the reduced tensile capacities of structural reinforcements because of the degradation of the material properties.In addition,the history of normal stress distributions of concrete under fire can be divided into three phases:expansion,stress redistribution and plateau phases.

Evaluation of soil arching effect due to partially mobilized shear stress in piled and geosynthetic-reinforced embankment

In piled and geosynthetic-reinforced(PGR) embankment, the arching behavior determines the overburden load on piles and subsoils. Placement of geosynthetic is effective in reducing the relative displacement between pile and subsoil. When the mobilized shear stress is less than the shear strength, partially developed arching will occur. Consequently, existing analytical methods, adopting the ultimate shear strength failure criterion, need to be improved. This study developed a simplified 2 D analytical method, which is based on the developing arching effect, to evaluate the load redistribution of the PGR embankment. Then, the influences of embankment height and internal friction angle, subsoil depth, ratio of pile cap width to pile clear spacing(RPC) and geosynthetic tensile stiffness on the critical height ratio, stress concentration ratio, soil arching ratio, geosynthetic tension and axial strain were investigated. This study suggests that a RPC of 1:1.0 and a one-way of single-layer geosynthetic tensile stiffness of 2000 kN/m should be considered as the sensitivity thresholds for the PGR embankment.

A parametric study on the contact stress of half toroidal continuously variable transmission

The most general contact in mechanical transmission is the elliptical one. In particular, a toroidal continuously variable transmission (CVT) has an elliptical shape in the contact area under the elastohydrodynamic lubrication regime, where the shearing of the fluid subjects to high contact stress and transmits the power. Many parameters affect the contact service performance of the half toroidal CVT, which include the properties of the contacting material (Young抯 modulus), operating parameters (input torque and maximum traction coefficient) and geometrical parameters (aspect cavity ratio, curvature ratio and half cone angle of the power roller). In this paper, the contacts between the input disk, the power roller and the output disk are formulated using the classical Hertzian contact theory. Based on the formulated equations, different system parameters, which affect the maximum Hertzian stresses, are compared. The comparative results will provide some observations of the relations between the maximum Hertzian stresses and transmission ratios in the form of graphs. These graphs give useful information for designer to know the maximum Hertzian stress during operation in such systems.

Influence of local geometric parameters on fatigue performance of orthotropic steel deck

Fatigue has become critical issue for bridge with orthotropic steel deck.Number of stress cycle and equivalent stress amplitude were adopted as two investigated fatigue effects.As presented from fatigue monitoring comparison of two series-lined bridges,three local geometric parameters of steel box girder have significant influence on fatigue performance of two welded joints.They are thickness of longitudinal ribs(Tr),longitudinal spacing of transverse floor plate(Sc)and longitudinal truss(LT).Fatigue analytical models were created for parametric study of fatigue effects under wheel load.Consequently,three local parameters have exhibited insignificant influence on number of stress cycle.Compared with Tr and Sc,configuration of LT has brought about foremost effect on the equivalent stress amplitude.For equivalent stress amplitude of rib-to-deck and rib-to-rib welded joints,the influence regions of LT are respectively longitudinal strap and quadrate with the geometric length of 600 mm.Enough attention ought to be paid for local stiffen structure on fatigue performance of orthotropic steel deck in fatigue design and monitoring.

Towards an Ecological Understanding of Translation Etemality in the Context of Iran

This study attempted to investigate the similarities and differences regarding the conceptions of translation eternality among a small group of Iranian people of different social positions and different ages. Sixty-two participants were selected based on the maximum variation sampling. To gather data, semi-structured interview was utilized. The participants were asked a list of 11 questions collected from the existing literature on the similar topics. Then, the interviews were transcribed for analyzing the data. Besides, Erikson＇s （1959） theory of development was used to classify participants of different ages in four groups of teenager, young, middle age, and old. The high frequency factors were found and analyzed with the use of Bronfenbrenner＇s （1979） nested ecological model. Moreover, the participants were classified in 11 groups based on their social positions and their conceptions were analyzed with the same method. Broadly speaking, 17 central tendencies in the interviews were obtained： People mainly focused on subjects of the books, translation fluency, author＇s competence in writing, and translator＇s competence, translations which have common grounds with social events of Iran, advertisement, existence of movie or cartoon adaptation of the book, translator＇s awareness of the content of the book, existence of cultural similarities between the source and target culture, popularity of the translator, author, and the original book, conversational language in translation, translation fidelity, being both translator and author, and effect of censorship on translation. Besides, old participants seemed to have more precise view on translation eternality and teenager＇s concerns were mostly about the appearance-related issues.

Effects of annealing temperature on microstructure and ferroelectric properties of Bi_(0.5)(Na_(0.85)K_(0.15))_(0.5)TiO_3 thin films

Bi0.5(Na0.85K0.15)0.5TiO3(BNKT15) thin films were synthesized by metal-organic decomposition(MOD) at annealing temperatures of 650,680,710 and 740℃,and the effects of annealing temperature on the microstructure,dielectric properties,remnant polarization(2Pr) and leakage current density were studied with X-ray diffractometer,atomic force microscope,precision impedance analyzer,ferroelectric analysis station and semiconductor parameter tester.The results show that the thin film annealed at 710℃ exhibits a typical perovskite structure without predominant orientation and a smooth surface with evenly distributed grains.2Pr value(67.4 μC/cm2 under 830 kV/cm) and the leakage current density(1.6×10-6 A/cm2 at 170 kV/cm) for BNKT15 thin film annealed at 710℃ are better than those for thin films annealed at other temperatures.

THEORY ANALYSIS AND EXPERIMENT STUDY ON THE FRACTURE PROPAGATION UNDER BLASTING LOAD

This paper theoretically analyzed and discussed the fractures’ initiation, propagation and arrest of grooved borehole blasting under the function of explosion, and provided the optimistic values of blasting parameters. The stress intensity factor and velocity of crack propagation were measured through dynamic caustics measuring system.

Discussion of Research Related to Structural Plane of Rock Mass Slope

In this paper, firstly, the rock slope and rock mass structure are introduced. And then, two aspects of the study of the structural plane are discussed： The first aspect is method for determining mechanical parameters of structural plane; The second aspect is analysis of shear strength of structural plane.

SPH-FEM simulations of microwave-treated basalt strength

Microwave precondition has been highlighted as a promising technology for softening the rock mass prior to rock breakage by machine to reduce drill bit/cutter wear as well as inverse production rate.To numerically explore the effect of numerical parameters on rock static strength simulation,and determine the numerical mechanical parameters of microwave-treated basalts for future drilling and cutting simulations,numerical models of uniaxial compression strength(UCS)and Brazilian tensile strength(BTS)were established with the coupling of smoothed particle hydrodynamics and finite element method(SPH-FEM).To eliminate the large rock strength errors caused by microwave-induced damage,the cohesion and internal friction angle of microwave-treated basalt specimens with the same microwave treatment parameters were calibrated based on a linear Mohr-Coulomb theory.Based on parametric sensitivity analysis of SPH simulation of UCS and BTS,experimental UCS and BTS values were simultaneously captured according to the same set of calibrated cohesion and internal friction angle data,and the UCS modeling results are in good agreement with experimental tests.Furthermore,the effect of microwave irradiation parameter on the basalt mechanical behaviors was evaluated.

Statistical Analysis of the Dynamic Parameters of Silty Clay in the Beijing Area

Soil dynamic parameters,including dynamic shear modulus ratio and damping ratio,have important effects on the results of layered soil earthquake response. In this paper,the mean parameter values of silty clay in different depths are obtained after statistical analysis of the experimental soil dynamic data from 20 recent site seismic safety evaluation reports in the Beijing area. Furthermore,based on two typical engineering sites,the influence of four different soil dynamic parameters,the statistic mean values,experimental values, values recommended by Yuan Xiaoming,and the values recommended in the code for seismic safety evaluation of engineering sites( DB001-94) are analyzed. The result shows that mean statistical values are applicable to seismic safety evaluation work in the Beijing area,especially for some inter-layered silty clays whose undisturbed soil samples are hard to obtain.

THE APPLICATION OF GENETIC ALGORITHM IN NON-LINEAR INVERSION OF ROCK MECHANICS PARAMETERS

The non-linear inversion of rock mechanics parameters based on genetic algorithm is presented. The principIe and step of genetic algorithm is also given. A brief discussion of this method and an application example is presented at the end of this paper. From the satisfied result, quick, convenient and practical new approach is developed to solve this kind of problems.

Development of Cubic Bezier Curve and Curve-Plane Intersection Method for Parametric Submarine Hull Form Design to Optimize Hull Resistance Using CFD

Optimization analysis and computational fluid dynamics （CFDs） have been applied simultaneously, in which a parametric model plays an important role in finding the optimal solution. However, it is difficult to create a parametric model for a complex shape with irregular curves, such as a submarine hull form. In this study, the cubic Bezier curve and curve-plane intersection method are used to generate a solid model of a parametric submarine hull form taking three input parameters into account： nose radius, tail radius, and length-height hull ratio （L/H）. Application program interface （API） scripting is also used to write code in the ANSYS DesignModeler. The results show that the submarine shape can be generated with some variation of the input parameters. An example is given that shows how the proposed method can be applied successfully to a hull resistance optimization case. The parametric design of the middle submarine type was chosen to be modified. First, the original submarine model was analyzed, in advance, using CFD. Then, using the response surface graph, some candidate optimal designs with a minimum hull resistance coefficient were obtained. Further, the optimization method in goal-driven optimization （GDO） was implemented to find the submarine hull form with the minimum hull resistance coefficient （Ct）. The minimum C, was obtained. The calculated difference in （7, values between the initial submarine and the optimum submarine is around 0.26%, with the C, of the initial submarine and the optimum submarine being 0.001 508 26 and 0.001 504 29, respectively. The results show that the optimum submarine hull form shows a higher nose radius （rn） and higher L/H than those of the initial submarine shape, while the radius of the tail （r1） is smaller than that of the initial shape.

The Study of CAD ＆ Processing Error for End-Gear with Arc Tooth

This paper presents methods for determining the basic geometry of end-gear with arc tooth external diameter, width of tooth, end module, number of teeth, pressure angle, tooth, tooth clearance parameters; at the same time gives the tooth bearing strength calculation method, and the formulas to calculate the tooth shear stress, surface stress and bolt fastening force of equivalent stress is established; finally write the software error simulation analysis.

Design and integrated simulation of a pressurized feed system of the dual-thrust hybrid rocket motor

A new pressurized feed system of the dual-thrust hybrid rocket motor for flight is presented in this paper.The feed system supplies 90% hydrogen peroxide (90%H 2 O 2) with two different flows of 4.5 and 2 kg s 1.The oxidizer flow is changed through regulating the mass flow of the high-pressure gas and switching the performance modes of the unique oxidizer flow control valve simultaneously.The models of the gas storage container,pressure regulator valve,control orifice,propellant tank,oxidizer flow control valve and cavitating venturi are generated and used to compute the instantaneous pressure,temperature and mass flow rate.There is a good agreement between the simulated and experimental results.Parameter sensitivity analysis is also conducted.It is found that the throat diameter of the cavitating venturi in feed line 1 is the main factor affecting the mass flow in both boost and sustaining phase.Other parameters have limited effects on the mass flow rate and the transition time of the system.

Power Network Parameter Estimation Method Based on Data Mining Technology

The parameter values which actually change with the circumstances, weather and load level etc. produce great effect to the result of state estimation. A new parameter estimation method based on data mining technology was proposed. The clustering method was used to classify the historical data in supervisory control and data acquisition （SCADA） database as several types. The data processing technology was implied to treat the isolated point, missing data and yawp data in samples for classified groups. The measurement data which belong to each classification were introduced to the linear regression equation in order to gain the regression coefficient and actual parameters by the least square method. A practical system demonstrates the high correctness, reliability and strong practicability of the proposed method.