基于踏板力和力变率的离合器操纵舒适性评价

文章针对人们对汽车舒适性要求的提高,从踏板力和行程的角度出发,分析踏板力及力变率对汽车离合器操纵舒适性的影响;通过分析离合器操纵机构,利用操纵过程中异点数量、踏板力与踏板行程线性度以及力变率对操纵舒适性进行评价,并建立了相应的评价模型和客观评价标准;最后通过实验数据验证了评价标准的合理性、可行性。

变加速动力学和三阶微分方程

阐明了梅凤翔在《高等分析力学》一书中给出的完整系统关于广义速度的Lagrange方程就是沈惠川在"吴大猷先生点评《经典力学》"一文中设想要仿照Lagrange方程寻找的新的动力学方程(简称为赝La grange方程).分析并指出了匀加速运动方程是赝Lagrange方程的第一积分.应用赝Lagrange方程求解了收尾速度问题中的急动度.

辐射阻尼力和电磁质量的动力学本质

"辐射阻尼力"是一种力变率的猝量.电磁质量是辐射反作用力变率的另一作用效果.辐射反作用力变率的物质来源是带电粒子的辐射场.

从传统牛顿力学到当今猝变动力学

引入急动度和猝变动力学等新概念,用以充实大学物理教学内容,是一种正在形成的趋势.本文提供了一个关于猝变动力学新概念教学的初步框架.

关于变加速动力学运动的一些基本概念

急动度(或力变率)的副法线分量描述了加速度(或力)随密切面旋转的物理图像.猝量方程和加速度能定理对解释电磁辐射阻尼和自由落体的初始猝变等问题提供了恰当的理论依据.以广义力变率表述的三阶Lagrange方程是对以广义力表述的二阶Lagrange方程的恰当补充.

竞技体育中的变加速运动及其概念规范

研究了短跑的“收尾速度”模型.在收尾速度模型中,收尾速度vm与过程特征参量k成反比,而过程特征参量k不是个人参量.在讨论变加速运动问题时,我们建议使用科学的规范用语,比如:急动度,力变率.

Dynamic globularization kinetics during hot working of TA15 titanium alloy with colony microstructure

The dynamic globularization kinetics of TA15（Ti-6Al-2Zr-1Mo-1V） titanium alloy with a colony α microstructure during deformation at temperature range of 860-940 ℃ and strain rate range of 0.01-10 s-1 was quantitatively studied through isothermal compression tests.It is found that the dynamic globularization kinetics and the kinetics rate of TA15 are sensitive to deformation parameters.The dynamic globularized fraction increases with increasing strain,temperature but decreasing strain rate.The variation of globularized fraction with strain approximately follows an Avrami type equation.Using the Avrami type equation,the initiation and completion strains for dynamic globularization of TA15 were predicted to be 0.34-0.59 and 3.40-6.80.The kinetics rate of dynamic globularization increases with strain at first,then decreases.The peak value of kinetics rate,which corresponds to 20%-33% globularization fraction,increases with increasing temperature and decreasing strain rate.

Uniaxial compressive behavior of equal channel angular pressing Al at wide temperature and strain rate range

Uniaxial compressive experiments of ultrafine-grained Al fabricated by equal channel angular pressing(ECAP) method were performed at wide temperature and strain rate range. The influence of temperature on flow stress, strain hardening rate and strain rate sensitivity was investigated experimentally. The results show that both the effect of temperature on flow stress and its strain rate sensitivity of ECAPed Al is much larger than those of the coarse-grained Al. The temperature sensitivity of ultrafine-grained Al is comparatively weaker than that of the coarse-grained Al. Based on the experimental results, the apparent activation volume was estimated at different temperatures and strain rates. The forest dislocation interactions is the dominant thermally activated mechanism for ECAPed Al compressed at quasi-static strain rates, while the viscous drag plays an important role at high strain rates.

Effects of alloying and deformation on microstructures and properties of Cu-Mg-Te-Y alloys

New copper alloys with high mechanical properties and high electrical conductivity were prepared, and the effects of addition of minor Mg and Y elements on microstructures and properties were studied. The high tensile strength of above 510 MPa, high elongation of 11%and high electrical conductivity of over 63%IACS can be simultaneously obtained in Cu-0.47Mg-0.20Te-0.04Y alloy after deforming and annealing treatment. Effects of purification together with the grain refining by Y and solid-solution strengthening by Mg are appropriate for enhancing mechanical properties and electrical conductivity of the copper alloys.

Effect of Zr and Sc on mechanical properties and electrical conductivities of Al wires

In order to obtain the Al wires with good mechanical properties and high electrical conductivities, conductive wires of Al-0.16 Zr, Al-0.16 Sc, Al-0.12Sc-0.04Zr（mass fraction, %） and pure Al（99.996%） were produced with the diameter of 9.5 mm by continuous rheo-extrusion technology, and the extruded materials were heat treated and analyzed. The results show that the separate additions of 0.16% Sc and 0.16% Zr to pure Al improve the ultimate tensile strength but reduce the electrical conductivity, and the similar trend is found in the Al-0.12Sc-0.04 Zr alloy. After the subsequent heat treatment, the wire with the optimum comprehensive properties is Al-0.12Sc-0.04 Zr alloy, of which the ultimate tensile strength and electrical conductivity reach 160 MPa and 64.03%（IACS）, respectively.

Static and dynamic mechanical behaviour of ECO-RPC

Ecological reactive powder concrete (ECO-RPC) with small sized and differentvolume fraction steel fibers was prepared by substitution of ultra-fine industrial waste powder for50% to 60% cement by weight and replacement of ground fine quartz sand with natural fine aggregate.The effect of steel fiber volume fraction and curing ages on the static mechanical behaviour ofECO-RPC was studied. Using the split Hopkinson pressure bar technique, the dynamic mechanicalbehaviour of ECO-RPC was investigated under different strain rates. The results show that the staticmechanical behaviour of ECO-RPC increases with the increase of steel fiber volume fraction andcuring ages. The type of ECO-RPC with the substitution of 25% ultra-fine slag, 25% ultra-fine flyash and 10% silica fume is better than the others with compressive strength, flexural strength, andfracture energy more than 200 MPa, 60 MPa and 30 kJ/m^2, respectively. ECO-RPC has excellent strainrate stiffening effects under dynamic load. Its peak stress, peak strain and the area understrain-stress curve increase with the increase of strain rate. Its fracture pattern changes frombrittleness to toughness under high strain rates.

Modeling Dynamical Noises Corrupted Chaotic System for Heart Rate Variability Analysis

It is difficult to establish the process of chaos in time series from cardiac dynamics. The output from such a system is probably the result of both its internal dynamics, and the input to the system from its surroundings. We present an optimization algorithm to find a time series that is as close as possible to the heart rate series subject to the constraint that it is deterministic with respect to some dynamics. The algorithm is tested by some famous forced dynamical systems, and applied to heart rate data. We find that the deterministic components of heart rate variability are chaotic.

Anti-Plane Elasticity Problem and Mode Ⅲ Crack Problem of Cubic Quasicrystal

The fracture theory of cubic quasicrystal was developed. The exact analytic solution of a Mode Ⅲ Griffith crack in the material was obtained by using the Fourier transform and dual integral equations theory, and so the displacement and stress fields, the stress intensity factor and strain energy release rate were determined. The results show that the stress intensity factor is independent of material constants, and the strain energy release rate is dependent on all material constants. These provide important information for studying the deformation and fracture of the new solid material.

Microstructure evolution of Al-Zn-Mg-Cu alloy during non-linear cooling process

The microstructure evolution and properties of an Al-Zn-Mg-Cu alloy were investigated under different non-linear cooling processes from the solution temperature, combined with in-situ electrical resistivity measurements, selected area diffraction patterns （SADPs）, transmission electron microscopy （TEM）, and tensile tests. The relative resistivity was calculated to characterize the phase transformation of the experimental alloy during different cooling processes. The results show that at high temperatures, the microstructure evolutions change from the directional diffusion of Zn and Mg atoms to the precipitation of S phase, depending on the cooling rate. At medium temperatures, q phase nucleates on A13Zr dispersoids and grain boundaries under fast cooling conditions, while S phase precipitates under the slow cooling conditions. The strength and ductility of the aged alloy suffer a significant deterioration due to the heterogeneous precipitation in medium temperature range. At low temperatures, homogeneously nucleated GP zone, η′ and η phases precipitate.

DETERMINATION OF PRESSURIZING CURVE AND COMPUTER CONTROL OF THICKNESS THINNING FOR SUPERPLASTIC BULGING

This paper proposes the assumption that the flow with viscous friction is the stretch of part of the sheet that lies along the walls of a die during the process of superplastic bulging according to superplastic flow equation and geometrical model of bulging of a sheet into a long trapezoid groove or truncated cone, by introducing the friction-factor P which describes the friction effect on the process. Also, the paper proposes the method of controlling thickness nonuniformity and develops the equipment which for uniform thickness of bulging, is automatically controlled with a computerl it also analyzes the important innuence of lubrication on thickness distribution of bulging materials. By the assumption, the relationship between bulging pressure and time is obtained in bulging of a sheet into the groove and cone, and p-t curve of multi-mould-cavity complicated bulging is discussed based on the analysis of single-mould-cavity bulging characteristics.

Plastic flow behavior of superalloy GH696 during hot deformation

In order to investigate the hot deformation behavior of superalloy GH696, isothermal compression experiments were carried out at deformation temperatures of 880?1120 °C and strain rates of 0.01?10 s?1. And the deformation amount of all the samples was 50%. The strain rate sensitivity exponent (m) and strain hardening exponent (n) under different deformation conditions were calculated, meanwhile the effects of the processing parameters on the values ofm andn were analyzed. The results show that the flow stress increases with the increase of strain rate and the decrease of deformation temperature. The value ofm increases with the increase of deformation temperature and decreases with the increase of strain rate, while the value ofn decreases with the increase of deformation temperature. A novel flow stress model during hot deformation of superalloy GH696 was also established. And the calculated flow stress of the alloy is in good agreement with the experimental one.

Effects of strain rate on mechanical properties, microstructure and texture of Al-Mg-Si-Cu alloy under tensile loading

The effects of strain rate on the mechanical properties,microstructure and texture of Al-Mg-Si-Cu alloy were investigated through tensile test,microstructure and texture characterization.The results show that strain rate has some influences on the mechanical properties and microstructure,but a slight influence on the texture.Overall,yield strength,ultimate tensile strength and elongation increase first,then remain unchanged,and finally increase with increasing strain rate.Independent of strain rate,microstructure in the vicinities of the fracture regions of all the specimens is composed of the slightly elongated grains.However,some differences in misorientation angle distributions can be observed.As strain rate increases,the low angle grain boundaries(LAGBs)increase first,and then decrease.Textures in the vicinities of the fracture regions are almost identical with increasing strain rate.

Mechanical properties and stress corrosion cracking behaviour of AZ31 magnesium alloy laser weldments

An AZ31 HP magnesium alloy was laser beam welded in autogenous mode with AZ61 filler using Nd-YAG laser system.Microstructural examination revealed that the laser beam weld metals obtained with or without filler material had an average grain size of about 12 μm.The microhardness and the tensile strength of the weldments were similar to those of the parent alloy.However,the stress corrosion cracking （SCC） behaviour of both the weldments assessed by slow strain rate tensile （SSRT） tests in ASTM D1384 solution was found to be slightly inferior to that of the parent alloy.It was observed that the stress corrosion cracks originated in the weld metal and propagated through the weld metal-HAZ regions in the autogenous weldment.On the other hand,in the weldment obtained with AZ61 filler material,the crack initiation and propagation was in the HAZ region.The localized damage of the magnesium hydroxide/oxide film formed on the surface of the specimens due to the exposure to the corrosive environment during the SSRT tests was found to be responsible for the SCC.

Constitutive analysis of AZ31 magnesium alloy plate

The plastic deformation simulation of AZ31 magnesium alloy at different elevated temperatures （from 473 to 723 K） was performed on Gleeble-1500 thermal mechanical simulator at the strain rates of 0.01, 0.1, 1, 5 and 10 s-t and the maximum deformation degree of 80%. The relationship between the flow stress and deformation temperature as well as strain rate was analyzed. The materials parameters and the apparent activation energy were calculated. The constitutive relationship was established with a Zener-Hollomon （Z） parameter. The results show that the flow stress increases with the increase of strain rate at a constant temperature, but it decreases with the increase of deformation temperature at a constant strain rate. The apparent activation energy is estimated to be 129-153 kJ/mol, which is close to that for self-diffusion of magnesium. The established constitutive relationship can reflect the change of flow stress during hot deformation.

Grain refinement and mechanical properties of pure aluminum processed by accumulative extrusion bonding

Ultrafine-grained aluminum processed by a new severe plastic deformation technique, accumulative extrusion bonding (AEB), was investigated. Microstructural characterization indicated good interfacial bonding and an average grain size of ~440 nm was obtained after six passes. Tensile testing revealed that the strength reached the maximum value of 195 MPa and the total elongation exceeded 16% after five passes. The hardness was also significantly improved and almost reached saturation after the first pass. SEM fractography of AEB-processed specimens after tensile test showed that failure mode was shear ductile fracture with elongated shallow dimples. Comparison with conventional accumulative roll bonding indicates that this new AEB technique is more effective in refining grain and improving mechanical properties of the specimens.