水平磁系高梯度磁选机精矿管堵塞原因分析与改造

南京梅山选矿厂针对水平磁系高梯度磁选机在现场使用中暴露出的精矿管堵塞的问题,通过测量水平磁系高梯度磁选机不同位置的漏磁场强度,对磁系的漏磁场分布特性进行研究。研究得出,精矿管堵塞为漏磁场导致,从力场计算结果得出,磁系漏磁产生的最大磁场力可使粒度大于0.3 mm的磁铁矿颗粒在精矿管中发生沉积。

Discussion of Grid Generation for Catamaran Resistance Calculation

In order to get some useful parameters for grid generation of catamaran, the CFD software FLUENT is used to investigate the main effects of grid generation on flow field calculation. The influences of some elements are investigated with a series of calculations in the present paper, and some alteratives are proposed. The proposed alteratives based on the analysis of the effects are used for a catamaran resistance calculation, comparisons of the calculated results with experimental data show good agreement. It shows that the research result of this paver is useful for the numerical calculation of catamaran.

Analysis of a Propeller Wake Flow Field Using Viscous Fluid Mechanics

The computational fluid dynamics （CFD） method is used to numerically simulate a propeller wake flow field in open water. A sub-domain hybrid mesh method was adopted in this paper. The computation domain was separated into two sub-domains, in which tetrahedral elements were used in the inner domain to match the complicated geometry of the propeller, while hexahedral elements were used in the outer domain. The mesh was locally refined on the propeller surface and near the wake flow field, and a size function was used to control the growth rate of the grid. Sections at different axial location were used to study the spatial evolution of the propeller wake in the region ranging from the disc to one propeller diameter （D） downstream. The numerical results show that the axial velocity fluctuates along the wake flow; radial velocity, which is closely related to vortices, attenuates strongly. The trailing vortices interact with the tip vortex at the blades＇ trailing edge and then separate. The strength of the vortex shrinks rapidly, and the radius decreases 20% at one diameter downstream.

Ab initio Study of Anharmonic Force Field and Spectroscopic Constants for Germanium Dichloride

Ab initio study of the equilibrium structure, spectroscopy constants, and anharmonic force field for several isotopomers of germanium dichloride （70GeCl2, 72GECl2, and 76GeCl2） have been carried out at the MP2 and CCSD（T） levels of theory using cc-pVTZ basis set. The cal- culated geometries, rotational constants, vibration-rotation interaction constants, harmonic frequencies, anharmonic constants, quartic and sextic centrifugal distortion constants, cubic and quartic force constants are compared with experimental data. For small mass differences of the Ge isotopes, the isotopic effects for germanium dichloride are much weaker. The agreements are satisfactory for these two methods, but the deviations of CCSD（T） results are slightly larger than that of MP2, because of CCSD（T）＇s inadequate treatment of electron correlation in hypervalent Cl atom.

Eco-compensation of Wetlands in Yellow River Delta of Shandong Province,China

Wetlands play an important ecological role and provide many functions for people, yet wetlands are cur- rently decreasing and deteriorating. The ability to calculate an economic value for the loss of wetlands is becoming in- creasingly important for policy makers. In this study, remote sensing, field investigations, department visits, and other methods were used to survey wetland types, assess wetland area changes, and calculate wetland economic value. Mar- ket value loss and ecological ftmction value loss, caused by reduction of wetland area and environmental pollution were calculated using commonly accepted methods of market valuation, ecological valuation, environmental protection investment cost analysis, and outcome parameters. According to market value loss and ecological function value loss, preliminarily fund allocation for wetland and ecological compensation was calculated. This will provide an important reference for future Yellow River Delta eco-compensation studies.

Experimental and field study on dissipation coefficient of supersaturated total dissolved gas

The elevated supersaturation of total dissolved gas （TDG） downstream of a high-dam spill has deleterious effects on fish in a large range. A one-dimensional （l-D） longitudinal model is optimal for the prediction of supersaturated TDG dissipation over a long distance. The key issue of the model is to determine the dissipation coefficient accurately. In agreement with field observations and experiment data, dimensional analysis and regression were performed to propose a formula for estimating the dissipation coefficient of supersaturated TDG in various rivers and reservoirs, and it involves the effects of the turbulence intensity, the hydro-pressure and the solid-liquid interface. The friction velocity, water depth, hydraulic radius and Froude number are independent variables in the formula which are easy to determine in practical applications. The 1-D longitudinal model is implemented to calculate the dissipation of TDG in a reach of the Jinsha River. Good agreement is found between the calculated results and field data for both the dissipation coefficient and the dissipation process.

Evaluation of flow behavior in copper electro-refining cell with different inlet arrangements

The arrangement of electrolyte inlet in the copper electro-refining(ER)cell has a great influence on the local flow field,which affects the distribution of electrical current density in consequence.In order to understand the complicated phenomena ofelectrolyte flow behavior in vertical counter electrodes in full-scale copper ER cell,the three-dimensional computational fluiddynamics(CFD)models with four different arrangements of electrolyte inlets,i.e.,single inlet(SI),central bottom inlets(CBI),topside interlaced inlets(TII),and bottom side interlaced inlets(BII),were established to simulate the flow behavior.Simulation resultshave revealed that the parallel injection devices help to improve the electrolyte velocity between electrodes,and while the relativerange of electrolyte velocity in CBI exceeds that of TII and BII,which is more than4times,indicating its severer unequal flowdistribution.Meanwhile,the average velocity of electrolyte in BII is4times larger than that of SI due to its higher turbulenceintensity.Generally,one of the efficient ways to supply fresh copper solution rapidly and uniformly into the inter-electrode space is toadapt the arrangement of BII.By utilizing such an arrangement,the electro-refining under high electrical current density is possible,and the productivity can be increased in sequence.

Field tests on mechanical characteristics and strength parameters of red-sandstone

Large-scale field shear tests on ten specimens of the red-sandstone embankment at a highway in Hunan,China,were performed to examine mechanical characteristics and parameters of red-sandstone.The curves of thrust-displacement,failure mode,and shear strength parameters for red-sandstone with different water contents,different compactions,and different grain size distributions were obtained from the tests.A practical procedure of in-situ test for red-sandstone embankment was proposed to normalize the test equipment and test steps.Based on three-dimensional thrust-sliding limit equilibrium method,the formulas for calculating strength parameters of red-sandstone considering three-dimensional sliding surface were inferred.The results show that red-sandstone has typical complete curves of stress-strain,strain softening,which are caused by the special structure of red-sandstone;water content and compaction are important factors for strength and failure mode of red-sandstone;The average value of cohesion and internal friction angle of the specimens calculated by three-dimensional technique are 21.56 kPa and 29.29°,respectively,and those by traditional two-dimensional method are 25.52 kPa and 33.76°,respectively.

Effects of stator bending on pressure field and loss of transonic turbine stage

To study effects of the upstream flow field changing on the downstream flow field of transonic turbine, different three-dimensional bowed blades, which are the stator blades of transonic turbine stage, were designed in this paper. And then numerical calculations were carried out. The effects on downstream flow field were studied and analyzed in detail. Results show that, at the middle of stator blades, although the increasing Maeh number causes the increase of shock-wave strength and friction, the middle flow field of downstream rotors is improved obviously. It is an important change in transonic condition. This causes the loss of the rotor＇ s middle part decreased greatly. Correspondingly, efficiency of the whole transonic stage can be increased.

CFD simulation of high-temperature effect on EHD characteristics in a wire-plate electrostatic precipitator

A computational fluid dynamics （CFD） model is carried out to describe the wire-plate electrostatic precipitator （ESP） in high temperature conditions, aiming to study the effects of high temperature on the electro- hydrodynamic （EHD） characteristics. In the model, the complex interactions at high temperatures between the electric field, fluid dynamics and the particulate flow are taken into account. We apply different numerical methods for different fields, including an electric field model, Euler-Lagrange particle-laden flows model, and particle charging model. The effects of high temperature on ionic wind, EHD characteristics and collection effi- ciency are investigated. The numerical results show high temperature causes more significant effects of the ionic wind on the gas secondary flow. High viscosity of gas at high temperature makes particles follow the gas flow pattern more closely. High temperature reduces the surface electric strength, so that the mean electric strength weakens the space charging. On the contrary, there is an increase in the diffusion charging at high tem- perature compared with at low temperature. High temperature increases the ratio of mean drag force over mean electrostatic force actin~ on the ~atticles which mav contribute to a decline of collection efficiencv.

The Research on Optimization of the Multiphase Flow Field of Biogas Plant by Using CFD Software

The inner flow field of a biogas plant can be optimized by agitating the feedstock to be evenly distributed for a rising biogas production rate. A hydraulic agitator can be installed in the digester with outlets far above the bottom. Hydraulic mixing is essential in a solid-liquid two-phase flow process, in which large solid particles can be found at the initial stage and turn to being high-concentration viscous liquid （non-Newtonian fluid）. A 0.75 m3 digester was taken as a case study with CFD （computational fluid dynamics） software. The basic pattern was simulated by using water as the medium and the pattern of pseudo plastic fluid state was simulated by the Euler-Euler Model, then the effect of optimized design with bottom inflow and high dispersed outlets could be verified. Viewed from the mixing effects, the velocity of 0.6 m/s is better than l m/s for water medium, while 1 m/s better than 0.6 m/s for pseudo plastic fluid medium.

Effects of Surface Etch Hole Fault on the Velocity Field in Microchannel Reactors

Microchannel reactors are commonly used in micro-chemical technology. The performance of microreactors is greatly affected by the velocity field in the microchannel. The flow field is disturbed by the cylindrical etch holes caused by air dust on the microchannel surface during its processing procedure. In this approach, a two-dimensional computational fluid dynamics （CFD） model is put forward to study the effect of etch holes on flow field. The influenced area of single or two concave etch holes is studied for the case of laminar flow. The hole diameter, the Reynolds number and the distance between the center of holes are found to have influences on the flow field. Numerical results indicate that the effects of etch hole on the flow field should be evaluated and the way of choosing the economic class of cleanroom for microreactor manufacture is presented.

A new approach to quantifying vehicle induced turbulence for complex traffic scenarios

Traffic-related pollutants adversely affect air quality, especially in regions near major roadways. The vehicleinduced turbulence(VIT) is a significant factor that controls the initial dilution, dispersion, and ultimately the chemical and physical fate of pollutants by altering the conditions in the microenvironment. This study used a computational fluid dynamics(CFD) software FLUENT to model the vehicle-induced turbulence(VIT) generated on roadways, with a focus on impact of vehicle-vehicle interactions, traffic density and vehicle composition on turbulent kinetic energy(TKE). We show, for the first time, that the overall TKE from multiple vehicles traveling in series can be estimated by superimposing the TKE of each vehicle, without considering the distance between them while the distance is greater than one vehicle length. This finding is particularly significant since it enables a new approach to VIT simulations where the overall TKE is calculated as a function of number of vehicles. We found that the interactions between vehicles traveling next to each other in adjacent lanes are insignificant,regardless the directions of the traffic flow. Consequently, simulations of different traffic scenarios can be substantially simplified by treating two-way traffic as one-way traffic, with less than 5% difference in the overall volume-averaged TKE. We also developed equations that allow the estimation of the overall volume-averaged TKE as a function of the number and the type of vehicles.

Experimental Study on Calculation of Hydro-Geological Parameters for Unsteady Flow

After the linear analytical method of unsteady flow theory is further improved,an innovative and faster algorithm is introduced.The water storage in a confined aquifer is derived from the water transmissivity coefficient and the water-pressure conductivity coefficient.The water transmissivity coefficient is approximated by a Taylorseries expansion of drawdown,and the water-pressure conductivity coefficient is obtained by the average drawdown.In this algorithm,the distance of the observation points from the pumping well must be short.When the distance is as short as the radius of the main pumping well,the data of the drawdown difference between the sidewall and the center of pumping well are difficult to measure,but the same results can be achieved based on the assumption that the drawdown difference approximates to the drawdown of the observation wells at a radial distance from the pumping well according to the algorithm.Without the help of charts,this algorithm is more concise and efficient,which has been verified by the test of water pumping project in Tianjin Binhai International Airport.

Numerical Analysis of the Thermal Behavior of a Hermetic Reciprocating Compressor

A numerical model to predict the temperature field in a hermetic reciprocating compressor for household refrigeration appliances is presented in this work. The model combines a high resolution three-dimensional heat conduction formulation of the compressor＇s solid parts, a three-dimensional CFD （computational fluid dynamics） approach for the gas line domain and lumped formulations of the shell gas and the lubrication oil. Heat transfer coefficients are determined by applying CFD to the gas line side and correlations from the literature on the shell gas and oil side, respectively. The valve in the gas line simulation is modelled as a parallel moving fiat plate. By means of an iterative loop the temperature field of the solid parts acts as boundary condition for the CFD calculation of the gas line which returns a cycle averaged quantity of heat to the solid parts. Using an iteration method which is based on the temperature deviation between two iteration steps, the total number of iterations and consequently the computational time can be reduced. The loop is continued until a steady-state temperature field is obtained. Calculated temperatures of the solid parts are verified by temperature measurements of a calorimeter test bench.

Numerical Prediction of Flow Patterns after Various Pipe Fittings

An accurate prediction of flows using CFD depends on a large number of factors. In addition to discretizing the flow region, the correct definition of boundary or initial conditions and the choice of suitable numerical methods, the applied turbulence model influences the results of the flow simulation to a great extent. Therefore, a validation of the results with the experimental data is of great importance for a correct selection of a turbulence model. It is the scope of this paper to assess different turbulence models for the simulation of pipe flows. The calculation results of pipe flows through a combination of 90~ elbows and a 1/3 segmental orifice are compared with experimental measurement results. This has the advantage that the suitability of the turbulence models for simulating both shear and swirl flows can be investigated. Thus, the k-ω, k-ε model and the Launder Reece Rodi Reynolds stress model are compared with each other and experimental results. Furthermore, this investigation is extended through including a much more c detached-eddy simulation. This model provides better prediction of the flow by resolving the large eddies and modeling the small ones. The experimental results originate from LDV measurements over the entire pipe cross-section. This measuring method provides velocity vectors over the measured surface.

Calculation of Steady SF_6 Gas Flow through a 420 kV Circuit Breaker Nozzle and Electric Field Distribution

Special interest in current interruptions is dedicated to the processes close to the current zero instant, the so-called interaction region, which determines the circuit breakers＇ performance. The quantities of interest in this region are the distribution of temperature, density and pressure, velocity and gas mass flow along the electric arc axis, as well as the distribution of electric stress between contacts Calculation of steady SF_6 gas flow through the nozzle of a 420 kV circuit breaker at the current zero instant, for different arcing durations, was carried out using a commercial CFD （computational fluid dynamics） simulation tool. The calculation results were used to get insight into improvement possibilities of the SF_6 gas flow model used in the software for computer simulation of HV （high-voltage） circuit breakers. Electric field calculation results were performed for the same 420 kV circuit breaker, in order to estimate the breakdown voltage at the current zero instant.

Study on the computation method of temperature field of RCC dam

According to the construction characteristic of RCC dam cast by layers, three-dimensional finite element relocating mesh method is developed to simulate construction process and compute temperature field. The computation model of relocating mesh method is expatiated in detail; based on the thermodynamic properties of RCC materials, the feasibility and error of relocating mesh method are analyzed and demonstrated; The computation results in this article are verified by means of the temperature observation data of certain RCC gravity dam. The results show that the temperature field computed by three-dimensional finite element relocating mesh method can not only ensure the computation precision, but also improve the calculation efficiency greatly. This provides an effective method for simulating construction process and computing temperature field of RCC dam.

Effects of hydrostatic pressure and external electric field on the impurity binding energy in strained GaN/Al_xGa_(1-x)N spherical quantum dots

The binding energy and Stark effect energy shifts of a shallow donor impurity state in a strained GaN/AlxGa1-xN spherical finite-potential quantum dot (QD) are calculated using a variational method based on the effective mass approximation. The binding energy is computed as a function of dot size and hydrostatic pressure. The numerical results show that the binding energy of the impurity state increases, attains a maximum value, and then decreases as the QD radius increases for any electric field. Moreover, the binding energy increases with the pressure for any size of dot. The Stark shift of the impurity energy for large dot size is much larger than that for the small dot size, and it is enhanced by the increase of electric field. We compare the binding energy of impurity state with and without strain effects, and the results show that the strain effects enhance the impurity binding energy considerably, especially for the small QD size. We also take the dielectric mismatch into account in our work.

CFD Study on Local Fluid-to-Wall Heat Transfer in Packed Beds and Field Synergy Analysis

To reach the target of smaller pressure drop and better heat transfer performance, packed beds with small tube-to-particle diameter ratio(D/dp<10) have now been considered in many areas. Fluid-to-wall heat transfer coefficient is an important factor determining the performance of this type of beds. In this work, local fluid-to-wall heat transfer characteristic in packed beds was studied by Computational Fluid Dynamics(CFD) at different Reynolds number for D/dp=1.5, 3.0 and 5.6. The results show that the fluid-to-wall heat transfer coefficient is oscillating along the bed with small tube-to-particle diameter ratio. Moreover, this phenomenon was explained by field synergy principle in detail. Two arrangement structures of particles in packed beds were recommended based on the synergy characteristic between flow and temperature fields. This study provides a new local understanding of fluid-to-wall heat transfer in packed beds with small tube-to-particle diameter ratio.