TZ-2型数字式力检测仪

在岩土工程的测试中,各种力的测量是一项基本的工作.但在过去的测试中,力的数值一般要通过换算才能得到,有时还不能直接测得而需采用间接的方法.而TZ—2型数字式力检测仪是直读式的测量仪器,它可以直接测量土体中的孔隙水压力、土压力或者基础结构、水工建筑物中的内压力,也可以测量水深、水位变化或用来测定各种气、液态压力等.

机动车方向盘转向力-转向角检测仪转向角示值误差测量值的不确定度评定

本文分析了机动车方向盘转向力-转向角检测仪转向角示值误差测量值的不确定度的主要来源,介绍了转向角示值误差测量值的不确定度的评定方法和步骤,并给出了评定结果。

机动车方向盘转向力-转向角检测仪示值误差的不确定度分析

依据JJF1196-2008《机动车方向盘转向力-转向角检测仪校准规范》和JJF1059-1999《测量不确定度评定及表示》,对机动车方向盘转向力-转向角检测仪测量结果示值误差进行了不确定度评定,通过阐述测量过程中产生的各分量对示值误差的影响,得到了测量结果的扩展不确定度。

Research on the Testing Methods of Instrumental System in the Marine Magnetic Survey

Testing methods of instrumental system in the marine magnetic survey have been studied in this paper, and the feasibility of each method has been testified by the observed data. The conclusion shows that the method brought out can effectively eliminate the systematic error caused by the instrumental system, and greatly improve the surveying precision and the reliability of the survey results.

Validity and reliability of three methods of stiffness assessment

Background：Stiffness is commonly assessed in relation to injury and athletic performance.The purpose of this research was to compare the validity and reliability of 3 in vivo methods of stiffness assessment using 1 cohort of participants.Methods：To determine inter-day reliability,15 female netballers were assessed for stiffness twice within 1 week using unilateral hopping（vertical stiffness）,free oscillations of the calf,and myometry of various muscles of the triceps surae.To establish convergent construct validity,stiffness was compared to static and dynamic strength measurements.Results：Test–retest stiffness results revealed that vertical stiffness produced moderate to high reliability results and myometry presented moderate to very high reliability.In contrast,the free oscillation technique displayed low to moderate reliability.Vertical stiffness demonstrated a significa t correlation with rate of force development during a squat jump,whilst myometer stiffness measurements from 3 sites in the lower limb revealed significan correlations with isometric rate of force development.Further,significan negative correlations were evident between the eccentric utilisation ratio and various myometer stiffness results.No relationships were established between the free oscillation technique and any of the performance measurements.Conclusion：These results suggest that vertical stiffness and myometry are valid and reliable methods for assessing stiffness.

Deterioration mechanism and rapid detection of performances of an existing subgrade in southern China

To relieve the increasing traffic load, many early built highways need to be widened or reconstructed. The rapid performance detection to existing subgrades is important to their reasonable evaluation and maximized utilization. Based on five kinds of soils taken from an existing highway in southern China, three commonly detecting methods were used to determine their moisture contents, compaction degrees and resilient moduli. The results showed that the measured moisture contents were greater than the design value, and the compaction degrees decreased sharply compared to the original ones. The moisture and heat exchange produced a decrease in the resilient modulus of plate loading test(PLT) from the standard 60 MPa down to 40 MPa. Afterwards, the portable falling weight deflectometer(PFWD) and dynamic cone penetrometer(DCP) were used to evaluate the subgrade performances. The measured PFWD moduli and the DCP penetration rates were correlated with the resilient moduli of PLT, deflections of the Beckman beam test, compaction degrees and moisture contents. The correlation analysis indicates that both of two methods are suitable in rapid detecting subgrade performances, but PFWD method is more recommended for it has higher accuracy and efficiency.

Detection Methods for MEMS-Based Xylophone Bar Magnetometer for Pico Satellites

Initially studied and developed by students in universities, the very small pico satellites （with a mass lower than 1 kg） are more and more considered for science applications. In particular, there are plans to use them in constellations of small spacecraft for remote sensing of various regions of the magnetosphere. They require a payload with specific size, weight and power consumption. In order to respond to this demand, new instruments have to be developed. Those instruments should exhibit at least the same performances as those used in larger satellites while fulfilling the specific requirements imposed by the satellites size. For this reason, the authors currently develop a xylophone bar magnetometer （XBM） based on micro-electromechanical systems （MEMS） with integrated detector electronics. The principle of this magnetometer is based on a classical resonating xylophone bar. A sinnsoidal current oscillating at the fundamental bending resonant frequency of the bar is applied through the device, and when an external magnetic field is present, the resulting Lorentz force yields the bar to vibrate at its fundamental mode with a displacement directly proportional to the amplitude in one direction of the ambient magnetic field. When designing a MEMS XBM, the detection method is a crucial aspect. The measurement method largely influences the geometry of the magnetometer as well as the manufacturing technology. Due to the constraints in terms of size, weight and power consumption, the two most promising measurement methods are capacitive and piezoelectric ones. Several designs including these measurement techniques are presented and simulated under realistic conditions. First, designs including lateral electrodes for capacitive measurement are tackled based on Silicon-On-Insulator （SOI） process. For the piezoelectric detection, a new configuration based on Lead Zirconate Titanate （PZT）/Pt structure is introduced and leads to much better sensitivity than the traditional Pt/PZT/Pt sandwich structure. Finally, the principle of electronic circuits enabling high sensitivity and low power consumption are proposed.