电力纺

电力纺的经纬可采用单根或双根桑蚕丝,也可采用经2～3根,纬3～4根合并的桑蚕丝,先织成坯绸,再经炼染,成为成品。很早以前,纺丝企业将以土丝(即手工缫成的丝)为原料,用手动织机制成的面料称为纺绸。20世纪初。

Effect of thermo-mechanical treatment on microstructure and mechanical properties of wire-arc additively manufactured Al-Cu alloy

Wire-arc additive manufacture(WAAM)has great potential for manufacturing of Al-Cu components.However,inferior mechanical properties of WAAM deposited material restrict its industrial application.Inter-layer cold rolling and thermo-mechanical heat treatment(T8)with pre-stretching deformation between solution and aging treatment were adopted in this study.Their effects on hardness,mechanical properties and microstructure were analyzed and compared to the conventional heat treatment(T6).The results show that cold rolling increases the hardness and strengths,which further increase with T8 treatment.The ultimate tensile strength(UTS)of 513 MPa and yield stress(YS)of 413 MPa can be obtained in the inter-layer cold-rolled sample with T8 treatment,which is much higher than that in the as-deposited samples.The cold-rolled samples show higher elongation than that of as-deposited ones due to significant elimination of porosity in cold rolling;while both the T6 and T8 treatments decrease the elongation.The cold rolling and pre-stretching deformation both contribute to the formation of dense and dispersive precipitatedθ′phases,which inhibits the dislocation movement and enhances the strengths;as a result,T8 treatment shows better strengthening effect than the T6 treatment.The strengthening mechanism was analyzed and it was mainly related to work hardening and precipitation strengthening.

Effect of cold rolling deformation on microstructure evolution and mechanical properties of spray formed Al−Zn−Mg−Cu−Cr alloys

The impact of cold rolling deformation,which was introduced after solid solution and before aging treatment,on microstructure evolution and mechanical properties of the as-extruded spray formed Al−9.8Zn−2.3Mg−1.73Cu−0.13Cr(wt.%)alloy,was investigated.SEM,TEM,and EBSD were used to analyze the microstructures,and tensile tests were conducted to assess mechanical properties.The results indicate that the D1-T6 sample,subjected to 25%cold rolling deformation,exhibits finer grains(3.35μm)compared to the D0-T6 sample(grain size of 4.23μm)without cold rolling.Cold rolling refines the grains that grow in solution treatment.Due to the combined effects of finer and more dispersed precipitates,higher dislocation density and smaller grains,the yield strength and ultimate tensile strength of the D1-T6 sample can reach 663 and 737 MPa,respectively.In comparison to the as-extruded and D0-T6 samples,the yield strength of the D1-T6 sample increases by 415 and 92 MPa,respectively.

Effects of ultrasonic treatment on microstructure and mechanical properties of Mg-5Zn-2Er alloy

The effects of ultrasonic treatment on the microstructure and mechanical properties of Mg-5Zn-2Er alloy at room temperature （RT） and high temperature （HT） were investigated. The microstructure and mechanical properties of the samples were studied by OM, SEM and MTS material tester. The results show that the microstructure and mechanical properties are improved after the ultrasonic vibration. The best effects of ultrasonic vibration on microstructure and mechanical properties were obtained with the ultrasonic vibration power of 600 W and time of 100 s. The cavitation and acoustic streaming caused by ultrasonic treatment play a major role in refining the microstructure and increasing mechanical properties of the alloy.

充分利用多臂

将以前的多臂用于力织机已经十分陈旧,而现在的凸轮多臂又很昂贵。是一种较节省的途径,用凸轮驱动改造现有的系统。 在印度,力织机是出口及国内用纺织产业的主要生产设备之一。在这一领域,几乎所有的织机和多臂要么十分陈旧,要么即使是新的,也不过是旧机构的翻版而己。棉织业要取得成功,完全靠免检连续生产的能力,这又依赖于许多条件。织造技术类型是能否保证连续生产的重要因素之一。对力织机来说,所有的机构都会影响到织机运转的连贯性。其中,开口装置是关键。

Evenness Control of Rapier Loom Tension by Using Neural Network

The neural network model (NNM) is used to control the evenness of rapier loom tension and to model the uncertain parameters of drafting process. This model can estimate recursively the tension and incorporate predictive control strategies. After controlling the effect testing,it can be seen that the behavior is excellent following different set point and variations, such as the diameter of the beam of weaver, air stream, density of warp and weft, type of textile, etc. An optimum steady state scheme has been fixed in keeping evenness of tension of loom. This method improves obviously the efficiency and quality of production.

The Propulsive Force of the Water-jet to the Flying Weft in Water-jet Looms

In order to study the propulsive force on the water-jet to the flying weft in water-jet looms, a dynamic model has been established. Based on the analysis and example testing, an experiential formula of the propulsive force of the water-jet to the flying weft is obtained for the first time. The formula will profit the further research of the water-jet weft insertion and the production of textile.

Study of Water Jet Impulse in Water-Jet Looms

The watar jet impulse is brought forward to study the traction force of the water jet to the flying weft in water-jet looms. The distribution of the water jet impulse in the shed is tested by a sensor, and the influence of water jet parameters on the water jet impulse is analyzed.

Effects of extrusion temperature on microstructure evolution and mechanical properties of heterogeneous Mg−Gd alloy laminates via accumulated extrusion bonding

The influence of extrusion temperature on microstructure and mechanical properties of heterogeneous Mg−1Gd/Mg−13Gd laminate prepared by accumulated extrusion bonding was investigated.The results reveal that the Mg−1Gd/Mg−13Gd laminate forms a significant difference in grain size between the successive layers when extruded at 330℃,and this difference gradually disappears as the extrusion temperature increases from 380 to 430℃.Besides,the growth rate of recrystallized grains in fine-grained layers is faster than that in coarse-grained layers.Moreover,the diffusion ability of Gd element increases with elevating extrusion temperatures,promoting the increase and coarsening of precipitates in fine-grained layers.Tensile tests indicate that the sample extruded at 380℃ has a superior combination of strength and ductility.This is mainly attributed to the synergy of the heterogeneous texture between coarse and fine-grained layers,hetero-deformation induced strengthening and hardening.The fine-grained layers facilitate the activation of prismaticáañslips,while coarse-grained layers make it easier to active basaláañand pyramidalác+añslips,especially for the sample extruded at 380℃.The activation of pyramidalác+añslips contributes to coordinating further plastic deformation.

Simulation on microstructure evolution and mechanical properties of Mg-Y alloys: Effect of trace Y

The influence of trace Y on the microstructure evolution and mechanical properties of Mg_(100−x)Y_(x)(x=0.25,_(0.75),1.5,3,4,5,at.%)alloys during solidification process was investigated via molecular dynamics(MD)simulations.The results show that the Mg_(100−x)Y_(x) alloys are mainly characterized by a face-centered cubic(FCC)crystal structure;this is different from pure metal Mg,which exhibits a hexagonal close packed(HCP)structure at room temperature.Among these alloys,Mg_(99.25)Y_(0.75) has a larger proportion of FCC cluster structures,with the highest fraction reaching 56.65%.As the content of the Y increases up to 5 at.%(Mg95Y5 alloy),the amount of amorphous structures increases.The mechanical properties of the Mg_(100−x)Y_(x) alloys are closely related to their microstructures.The Mg_(99.25)Y_(0.75) and Mg_(97)Y_(3) alloys exhibit the highest yield strengths of 1.86 and 1.90 GPa,respectively.The deformation mechanism of the Mg−Y alloys is described at the atomic level,and it is found that a difference in the FCC proportion caused by different Y contents leads to distinct deformation mechanisms.

Use of Polypropylene Non-woven as Sorbent of Oil Small

In this work, the mechanical tensile and elongation properties and the non-woven polypropylene flammability were evaluated, with variations of gratings, compared to non-woven fabrics prepared with thermo film and TNT （fabric non-fabric）, for applications such as geotextile sorption of oil spills. The results showed high values of tensile strength for non-woven fabric prepared for application as geotextile, improving the mechanical properties of rupture.

Cost Sharing Based Truthful Spectrum Auction with Collusion-Proof

Spectrum auction is an important approach of spectrum distribution in cognitive radio networks. However, a single secondary user(SU) probably can't afford the price of spectrum. Multiple SUs grouping together to participate in the auction as a whole is helpful to increase purchasing power. However, SUs could suffer from a new group cheating problem, i.e., parts of users conspire to manipulate the auction by submitting untruthful bids. Existing auction mechanisms were mainly designed to be strategy-proof only for individual user and can't deal with group cheating. In this paper, a novel spectrum auction mechanism called COSTAG(COst Sharing based Truthful Auction with Group-buying) is proposed to address the group cheating problem. COSTAG consists of a grouping rule to perform grouping and a payment rule to determine the market-clearing price in the spectrum auction. Different from single-echelon pricing approach employed in existing works, a multi-echelon pricing strategy is designed to increase the transaction rate and optimize social profit for the auction. Comprehensive theoretical analysis shows that COSTAG can satisfy the crucial economic robustness properties, both individual and group truthfulness. Simulations demonstrate that comparing with existing works, COSTAG can improve the system performance significantly.

Effect of solution plus aging heat treatment on microstructural evolution and mechanical properties of near-β titanium alloy

The microstructural evolution, mechanical properties and fracture mechanism of a Ti.5Al.5Mo.5V.3Cr.1Zr (Ti-55531) alloy after solution (760.820℃) plus aging (580.640℃) treatments were investigated. The results show that the volume fraction of the primary α(αp) phase decreases with the increase of solution temperature, and the length of the secondary α phase (αs) decreases while its width increases with the increase of aging temperature. Yield and tensile strengths decrease with the increase of solution temperature, while increase with the increase of aging temperature. A good balance of tensile strength and ductility of the alloy is obtained under solution of 800℃ for 2 h plus aging of 640℃ for 8 h, in which the tensile strength is 1434 MPa and the elongation is 7.7%. The coarsening αs phase makes crack propagation paths deflected and tortuous, which increases the crack propagation resistance and improves the ductility and fracture toughness.

Effect of Cu on microstructure,mechanical properties,and texture evolution of ZK60 alloy fabricated by hot extrusion−shearing process

As-cast Mg-6Zn-xCu-0.6Zr(x=0,0.5,1.0,wt.%)alloys were fabricated by permanent mold casting;then,the alloys were subjected to homogenization heat treatment and extrusion-shearing(ES)process.The microstructure and mechanical properties of the alloys were evaluated by OM,SEM/EDS,XRD,TEM,EBSD and tensile tests.The results show that the hard MgZnCu phase in Cu-added alloy can strengthen particle-stimulated nucleation(PSN)effect and hinder the migration of dynamic recrystallization(DRX)grain boundary at an elevated temperature during ES.The ZK60+0.5Cu alloy shows an optimal tensile strength–ductility combination(UTS of 396 MPa,YS of 313 MPa,andδ=20.3%)owing to strong grain boundary strengthening and improvement of Schmid factor for{0001}■basal slip.The aggregation of microvoids around the MgZnCu phase mainly accounts for the lower tensile elongation of ZK60+1.0Cu alloy compared with ZK60 alloy.

Interfacial microstructure and mechanical behavior of Mg/Cu bimetal composites fabricated by compound casting process

Mg/Cu bimetal composites were prepared by compound casting method, and the microstructure evolution, phase constitution and bonding strength at the interface were investigated.It is found that a good metallurgical bonding can be achieved at the interface of Mg and Cu,which consists of two sub-layers,i.e.,layer I with 30μm on the copper side composed of Mg2Cu matrix phase, on which a small amount of dendritic MgCu2 phase was randomly distributed;layerⅡ with 140μm on the magnesium side made up of the lamellar nano-eutectic network Mg2Cu+(Mg) and a small amount of detached Mg2Cu phase. The average interfacial shear strength of the bimetal composite is measured to be 13 MPa.This study provides a new fabrication process for the application of Mg/Cu bimetal composites as the hydrogen storage materials.

Influence of different gravitational environments on the mechanotrans-duction in osteoblasts

Objective: To observe the effects of different gravitational environments on release of prostaglandin E2 in rat calvarial osteoblasts induced by fluid shear stress (FSS) so that to investigate the influence of different gravity on mechanotransduction in osteoblasts. Methods: Osteoblasts were isolated from neonatal rat calvariae and then were set to three groups. Each was cultured in one gravitational environment; 1G terrestrial gravitational environment (control), simulated weightlessness achieved by using clinostat and 3G gravitational environment achieved by using centrifuge for 60 h, then osteoblasts were treated with 0. 5 Pa or 1. 5 Pa FSS in a flow chamber for 1 h. The release of PGE2 in osteoblasts was determined. Results: In 1G gravitational environment, the release of PGE2 was significantly increased along with the sustaining of FSS treatments (P<0. 01), but there was no remarkable difference between the responses to 0. 5 Pa FSS and 1. 5 Pa FSS (P>0. 05). While in simulated weightlessness environment group, no detectable release of PGE2 was found with the treatment of 0. 5 Pa FSS (P<0. 01), and the release of PGE2 was delayed and the amount of PGE2 production was remarkably decreased with 1. 5 Pa FSS treatment as compared with that of 1G group (P<0. 01). The responsiveness of osteoblasts cultured in 3G gravitational environment to FSS was similar to that of 1G group. Conclusion: These results indicate that in vitro the mechanotransduction in osteoblasts iss affected by stimulated weightlessness, whereas it is not altered in 3G gravitational environment.

Effect of Al and Sc on deformation behavior of FeCoNi multi-element alloys

The effects of Al and Sc on mechanical properties of FeCoNi multi-element alloys(MEAs) were investigated by compressive tests. The microstructures of FeCoNi MEAs with different contents of Al and Sc were characterized and the strengthening mechanisms were discussed. The results show that FeCoNi MEA with a low content of Al has a face-centered cubic(FCC) structure. The yield strength increases linearly with the increase of Al content, which is largely caused by solid solution hardening. Further addition of Sc can promote the formation of a new phase in(FeCoNi)1-xAlx MEAs. A minor addition of Sc can significantly increase the yield strengths of(FeCoNi)1-xAlx MEAs with a low Al content and improve the compressive plasticity of(FeCoNi)1-xAlx MEAs with a high Al content.

Effects of minor Sc and Zr additions on mechanical properties and microstructure evolution of Al−Zn−Mg−Cu alloys

The effects of minor Sc and Zr additions on the mechanical properties and microstructure evolution of Al Zn Mg Cu alloys were studied using tensile tests, scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The ultimate tensile strength of the peak-aged Al Zn Mg Cu alloy is improved by about 105 MPa with the addition of 0.10% Zr. An increase of about 133 MPa is observed with the joint addition of 0.07% Sc and 0.07% Zr. For the alloys modified with the minor addition of Sc and Zr (0.14%), the main strengthening mechanisms of minor addition of Sc and Zr are fine-grain strengthening, sub-structure strengthening and the Orowan strengthening mechanism produced by the Al3(Sc,Zr) and Al3Zr dispersoids. The volume of Al3Zr particles is less than that of Al3(Sc,Zr) particles, but the distribution of Al3(Sc,Zr) particles is more dispersed throughout the matrix leading to pinning the dislocations motion and restraining the recrystallization more effectively.

Tensile Property of Bi-axial Warp Knitted Structure

The tensile property of bi-axial warp knitted fabrics is tested and compared with that of the plain weave fabric. The results show that there are obvious differences between the tensile property of a bi-axial warp knitted fabric and that of a plain weave fabric.The former can give fuller play to the property of a high modulus yarn than the latter. The tensile strength of a bi-axial warp knitted fabric is linear with the number of yarns in the direction of force.

Four driving forces for the advance of dyeing and printing equipment

The year of 2017 saw an obvious improvement in the sector of China’s textile machinery industry and an increase of the main business income and gross profit.Besides,foreign trade in textile machinery products grew in number.