交流转辙机全电子执行单元监测数据采集功能的实现方案

随着电子执行单元写入计算机联锁技术条件,电子执行单元在铁路干线工程中开始逐渐应用,由于先行的一些信号设备技术条件在编制之初,并未针对电子执行单元这一新型应用制定特定的技术条件内容,使得在具体工程实践时发现全电子执行单元在某些功能方面还有待改进。文章借用具体工程条件下实际应用案例,分析了交流转辙机继电控制电路监测数据采集原理及实施方案,阐述了电子执行单元在交流转辙机监测数据采集的功能需求及实现方案。

COMPARISON AND EVALUATION OF CURRENT REFERENCE GENERATION STRATEGIES FOR ACTIVE POWER FILTERS IN THREE-PHASE FOUR-WIRE SYSTEMS

For three phase four-wire active power filters （APFs）, several typical power theories and corresponding current reference generation strategies are induced, p-q, d-q, unify power factor （UPF） and instantaneous active current （IAC） methods are analyzed and compared with each other. The interpretation of active and reactive currents in non-sinusoidal and unbalanced three-phase four-wire systems is given based on the generalized instantaneous reactive power theory. The performance and the characteristic are evaluated, and the application conditions of current reference generation strategies are concluded. Simulation results under different source voltages and loads verify the evaluation result.

A New Structure for a CMOS Audio Power AMP with Extremely Low THD and Low Power Consumption

A new system-corrected CMOS audio power AMP is presented. Consisting of four single-end OPAs,this structure is a pseudo-differential system. Compared to conventional CMOS power AMPs, it has the merits of low power consumption, extremely low THD,easy compensation, and good driving capability. With 1st silicon 0.25μm 1P4M CMOS technology and a 3V power supply,the output range can be 4Vpp when driving an 8Ω‖ 300pF load, while its power dissipation is less than 3mW. The THD is better than 0. 003% at 1kHz. A new over-current protection circuit, which can effectively protect the power output circuits on the chip, is also demonstrated.

An Augmented Jacobian Method for Power Flow Analysis of Weakly Looped Distribution Systems with PV Buses

A power flow analysis method for weakly looped distribution systems with PV buses is proposed in this paper. The proposed method is computationally more efficient and more robust compared with the conventional compensation methods. The robustness is achieved by embedding the boundary conditions of loops and PV buses into the Jacobian matrix. The computational efficiency is achieved by the carefully designed factorization of Jacobian matrix. Test results on a 33 bus system are presented.

Dynamic modeling and direct power control of wind turbine driven DFIG under unbalanced network voltage conditions

This paper proposes an analysis and a direct power control (DPC) design of a wind turbine driven doubly-fed induction generator (DFIG) under unbalanced network voltage conditions. A DFIG model described in the positive and negative synchronous reference frames is presented. Variations of the stator output active and reactive powers are fully deduced in the presence of negative sequence supply voltage and rotor flux. An enhanced DPC scheme is proposed to eliminate stator active power oscillation during network unbalance. The proposed control scheme removes rotor current regulators and the decomposition processing of positive and negative sequence rotor currents. Simulation results using PSCAD/EMTDC are presented on a 2-MW DFIG wind power generation system to validate the feasibility of the proposed control scheme under balanced and unbalanced network conditions.

Failure analysis of a kind of low power connector

A kind of low power connector used e.g. in household appliances was partly burned in routine experiment. The heat sources were four paralleled contacts constructed by springs (Sn/CuSn-alloy) in socket and a plug sheet (Ni/Steel) while mating. The contact interfaces were detected by scanning electronic microscope (SEM) and X-ray energy dispersive spectros- copy (XEDS), obvious wear tracks and various contaminants, including element Si, Al, Na, K, S, Cl, O, etc., were found. The contamination degrees on the four paralleled contacts were different, so that the ratio of average contact resistance on the four contacts was about 5:8:3:1. The maximum contact resistance on contacts of the plug sheet reached 28 ?. The main failure rea- sons were fretting and contamination between the contact interfaces. Fretting simulation showed that connection resistance of connectors was raised up, even to ohms level. When the current increased to 5 A, the socket housing was heated and decom- posed. By the thermal analysis, it was estimated that the connector would be burned under the lower current if the current was not evenly distributed on the four paralleled contacts caused by uneven contamination. Improvement methods for connector failure are also discussed.

Simulation and reliability analysis of shunt active power filter based on instantaneous reactive power theory

This paper first discusses the operating principle of instantaneous reactive power theory. Then, the theory is introduced into shunt active power filter and its control scheme is studied. Finally, Matlab/Simulink power system toolbox is used to simulate the system. In the simulation model, as the most common harmonic source, 3-phase thyristor bridge rectifier circuit is constructed. The simulation results before and after the shunt active filter was switched to the system corresponding to different firing angles of the thyristors are presented and analyzed, which demonstrate the practicability and reliability of the proposed shunt active filter scheme.

Simulation of a kind of active harmonic reduction 18-pulse rectifier

To solve the input current harmonic pollution of the high power rectifier system,18-pulse rectifier based on a kind of active harmonic suppression technique at dc side is proposed in this paper.The pulse rectifier employs three-phase diode bridges,each of them followed by a boost converter.Unlike the conventional three-phase unity-power-factor diode rectifier,the ideal sinusoidal main currents of circuit topology are obtained by control its output current or input currents of three boost converters for approximately triangular modulation.The theoretical of modulation strategy and characteristics of input and output currents about the proposed rectifier are analyzed in detail.Simulation results by Matlab/Simulink demonstrate that the proposed rectifier draws nearly sinusoidal current and power quality index is improved.The correctness of the theoretical analysis is validated.

Multi-objective steady-state optimization of two-chamber microbial fuel cells

A microbial fuel cell(MFC)is a novel promising technology for simultaneous renewable electricity generation and wastewater treatment.Three non-comparable objectives,i.e.power density,attainable current density and waste removal ratio,are often conflicting.A thorough understanding of the relationship among these three conflicting objectives can be greatly helpful to assist in optimal operation of MFC system.In this study,a multiobjective genetic algorithm is used to simultaneously maximizing power density,attainable current density and waste removal ratio based on a mathematical model for an acetate two-chamber MFC.Moreover,the level diagrams method is utilized to aid in graphical visualization of Pareto front and decision making.Three biobjective optimization problems and one three-objective optimization problem are thoroughly investigated.The obtained Pareto fronts illustrate the complex relationships among these three objectives,which is helpful for final decision support.Therefore,the integrated methodology of a multi-objective genetic algorithm and a graphical visualization technique provides a promising tool for the optimal operation of MFCs by simultaneously considering multiple conflicting objectives.

Research on the variable speed system of large power alternating current motor

The development status of the variable speed system of large power AC(alternating current)motor drive in China is introduced.The large power AC drive fed by AC-AC converters(cycloconverters)has developed greatly,and some innovations on the theory and engineering technique have been realized.They have been applied to rolling mills,mine hoists,and so on,and remarkable economic and social benefit has been achieved.The development of AC drive fed by large power IGCT(integrated gate commutated thyristors)AC-DC-AC converter is also introduced.It has excellent performance and reliable operation,and has been used in traction.

Design of a novel 50kW fast charger for electric vehicles

A novel 50 kW fast charger was proposed for electric vehicles. The proposed fast charger is divided into two main sections an AC-DC converter performing a PFC function and a DC-DC converter performing a charging function. A transformer including leakage inductances was used in the AC-DC converter in order to obtain isolation and inductance. A series-connection topology was used in the DC-DC converter between the DC-bus and outlet. This topology enables high power conversion efficiency up to 95% for the DC-DC converter. In order to reduce the impact of the 50 kW charging on the AC grid, the proposed fast charger system includes a buffering battery unit between the two main power conversion units. This leads to reductions in the power installation costs of power companies and to improvements in the power quality were verified through simulations and experimental results. on the AC grid. The performances of the proposed fast charger system

Analysis on the Application of Reactive Power Compensation Technology in Electrical Automation

This paper introduces in detail the reactive power compensation technology and its characteristics, to reduce the loss of reactive power compensation technology 1N power distribution system and the electrical automation, improve the utilization rate, and realize the control of the voltage amplitude in the system network, voltage stability of power distribution system, has carried on the system analysis to reduce failure of the harmonic current to the power supply system and other functions. And the paper in-depth study on the application of reactive power compensation technology in electrical automation from the reactive compensation technology, substation and distribution line reactive power compensation, power users of reactive power compensation and other aspects.

A New-Style Two-Staged Dimmable Electronic Ballast

A two-staged electronic ballast with wide dimming range, high power factor(PF) and low electromagnetic interference(EMI) is presented. It changes the input voltage of the stage of power inverter for dimming control, so it overcomes some limitations of traditional electronic ballasts that use frequency variation. At the same time, the stage of power inverter runs under the soft-switching at the fixed switching frequency and reduces EMI greatly. Its principle and characteristic are analyzed in detail,and experimental and simulated results are obtained on a 40 W fluorescent lamp.

Fuzzy Logic Based Power Flow Control Analysis of Advanced Unified Power Flow Controller

Due to rapidly development of high power semiconductor devices with fast control features have made possible to control the power flow more efficiently and effectively. The Flexible AC Transmission Systems （FACTS） in this category introduces several innovative operating control devices. One of the recent devices is Advanced Unified Power Flow Controller （AUPFC） or multi-converter UPFC, which can control bus voltage and real and reactive power flows of more than one line or even a sub-network. This paper presents performance analysis of AUPFC based on d-q axis model theory. Based on the analysis, a new fuzzy logic rules based control algorithm has been developed in this paper which improves the system performance. The control rules are structured depending upon the relationship between series inserted voltages in multi-line and the desired changes of real and reactive power flows in the control network. The impacts of different controllers along with parameters of series connected transformers and transmission lines have been investigated through developed control block models in SIMULINK. The effectiveness of the proposed scheme is demonstrated by a case study.

Design and Performances of High-Current Modular Pulsed Power

A design of the high-current modular pulsed power generator and results of the test of this generator are presented. The generator is based on two capacitors each of 2.5μF and 50 kV maximum charging voltage. Two multi-gaps gas spark switches with capacitive coupled triggering are used to discharge stored energy into the load. The triggering pulse with amplitude up to 70 kV and rise time of-50 ns is supplied by three-stage Marx-generator. The output of each capacitor with multi-gaps spark switch is connected to the load by eight coaxial cables -1 m in length. The total inductance of the generator does not exceed 200 nil. At 40 kV charging voltage this generator produces 180 kA with a quarter of period of 1.6 μs at short circuit load of-15 nil. The generator has been used in the research of underwater electrical wire explosion. The space separation of the load and modules of generator allows one to avoid possible damages of the generator by shock waves produced during the wire explosion. In addition, this modular generator design allows to increase easily the number of modules and to reach several hundreds of kiloamperes in the load.

Resistance of LEDs Based on AIGalnP Heterostructures to Irradiation by Fast Neutrons

The change of light output power of LEDs based on A1GalnP heterostructures with multiple quantum wells （590 nm and 630 nm） under irradiation by fast neutrons depends on the operating current density. It can be distinguished the regions of high, average and low electron injection. Operating current, this corresponds to the position of the boundary between the selected levels of the electron injection, increases with increasing neutron fluence. The final stage of the reducing process of the light output power under irradiation is the regime of low electron injection. The relative change in light output power depends on the operating current （operating current density） and can be described by a fairly simple equation. Established relations predict radiation resistance of LEDs, and it makes the most rational justification of operating modes of light-emitting diodes in terms of radiation resistance.

Study on the Rural Electrification in Jordan

An investigation was conducted to install wind farm to supply electrical power to the village of Ras Munif, the highest elevation in Jordan. The village installed capacity load was found to be 500 kW. A 25 windmills, 20 kW each, forming the wind farm was found to be the best choice to supply the village with 100% of its needed power. The windmills will be spaced 50 meters along an unobstructed continuous wind flow location, along sloping sides of Ras Munif Mountain, alongside service road. The village load bus will be connected directly to both the output of wind farm inverter output bus and to the national grid bus. Both buses supply the needed power. The power flow was found to be supplied by the wind farm, except when the wind speed is low, the village load will be supplied partially or totally by the national grid bus.

Power Flow Calculation Method of Large Shipboard Power System

The effect of line voltage drop is considered larger on loads, especially on asynchronous motor, transformers and other non-linear load parameters in power system of large ships. A novel power flow method based on improved node voltage method is proposed, and a typical ship power system, which has 2 power stations and 10 nodes, with closed-loop design but open-loop operation, is taken as an example. Simulation results show that the improved power flow calculation method has achieved higher accuracy and better convergence.

Design Consideration for High Power Density GaN Buck-Rectifier in ISOP-IPOS Converter based dc Distribution, System

GaN （gallium nitride） buck-rectifier has been proposed to realize high power density ISOP （input series and output parallel）-IPOS （input parallel and output series） converter-based dc distribution system. The ultra-low loss bi-directional switch can be developed by the GaN power device because of the low on-resistance, the high-speed switching behavior and its own device structure. The buck-rectifier using the GaN bi-directional switches has the potential to achieve higher power density than the commonly utilized boost-rectifier. Availability of the GaN-HEMT （high electron mobility transistor） for the buck rectifier has been verified taking the theoretical limit of the on-resistance and the switching loss energy into account. Design consideration for a high power density buck-rectifier has been also conducted and the application effect of the GaN bidirectional switches has been evaluated quantitatively. The ISOP-IPOS converter-based dc （direct current） distribution system takes full advantage of the buck-rectifier and the rectifier using GaN devices contributes to realizing higher power density dc distribution system.

Physics of Power Semiconductor Streamer Laser

It is considered the mechanism of streamer discharge in the wide-gap semiconductors as a highly effective method of the laser excitation on the basis of representation about the phenomenon of light self-trapping of the discharge, providing their high propagation velocity down to v- 5 ×10^9 sm/s, the crystallographic orientation, filamentary character at thickness of the channel about 1 μm and absence of destructions of a crystal.