Pristine LiNi0.5Mn1.5O4and Na-doped Li0.95Na0.05Ni0.5Mn1.5O4cathode materials were synthesized by a simple solid-statemethod.The effects of Na+doping on the crystalline structure and electrochemical performance of LiN...Pristine LiNi0.5Mn1.5O4and Na-doped Li0.95Na0.05Ni0.5Mn1.5O4cathode materials were synthesized by a simple solid-statemethod.The effects of Na+doping on the crystalline structure and electrochemical performance of LiNi0.5Mn1.5O4cathode materialwere systematically investigated.The samples were characterized by XRD,SEM,FT-IR,CV,EIS and galvanostatic charge/dischargetests.It is found that both pristine and Na-doped samples exhibit secondary agglomerates composed of well-defined octahedralprimary particle,but Na+doping decreases the primary particle size to certain extent.Na+doping can effectively inhibit the formationof LixNi1-xO impurity phase,enhance the Ni/Mn disordering degree,decrease the charge-transfer resistance and accelerate the lithiumion diffusion,which are conductive to the rate capability.However,the doped Na+ions tend to occupy8a Li sites,which forces equalamounts of Li+ions to occupy16d octahedral sites,making the spinel framework less stable,therefore the cycling stability is notimproved obviously after Na+doping.展开更多
The conversion reaction-based anode materials of sodium ion batteries have relatively high capacity;however,the application of these materials is limited by their structural collapse due to the poor structure stabilit...The conversion reaction-based anode materials of sodium ion batteries have relatively high capacity;however,the application of these materials is limited by their structural collapse due to the poor structure stability.In this work,MoSe_(2) nanosheets were synthesized by a solvothermal method.An organic solvent was intercalated into the MoSe_(2) materials to enlarge the interlayer spacing and improve the conductivity of the material.The MoSe_(2) material was coated with an organic pyrolysis carbon and then a uniform carbon layer was formed.The surface carbon hybridization of the nanosheet materials was realized by the introduction of heteroatoms during the sintering process.The as-prepared MoSe_(2)@N,P-C composites showed a superior rate performance as it could maintain the integrity of the morphology and structure under a high current density.The composites had a discharge specific capacity of 302.4 mA·h/g after 100 cycles at 0.5 A/g,and the capacity retention rate was 84.96%.展开更多
A series of layered LiNi0.8?xCo0.1Mn0.1LaxO2(x=0,0.01,0.03)cathode materials were synthesized by combining co-precipitation and high temperature solid state reaction to investigate the effect of La-doping on LiNi0.8Co...A series of layered LiNi0.8?xCo0.1Mn0.1LaxO2(x=0,0.01,0.03)cathode materials were synthesized by combining co-precipitation and high temperature solid state reaction to investigate the effect of La-doping on LiNi0.8Co0.1Mn0.1O2.A new phase La2Li0.5Co0.5O4was observed by XRD,and the content of the new phase could be determined by Retiveld refinement and calculation.The cycle stability of the material is obviously increased from74.3%to95.2%after La-doping,while the initial capacity exhibits a decline trend from202mA·h/g to192mA·h/g.The enhanced cycle stability comes from both of the decrease of impurity and the protection of newly formed La2Li0.5Co0.5O4,which prevents the electrolytic corrosion to the active material.The CV measurement confirms that La-doped material exhibits better reversibility compared with the pristine material.展开更多
LiNi0.78 Co0.2 Al0.02O2 cathode materials were prepared with a novel co-precipitation method followed by heat-treating. The properties of the materials were characterized. XRD patterns showed that no secondary phase a...LiNi0.78 Co0.2 Al0.02O2 cathode materials were prepared with a novel co-precipitation method followed by heat-treating. The properties of the materials were characterized. XRD patterns showed that no secondary phase appeared and the hexagonal lattice parameter c of LiNi0.rsCoo.2AI^0202 was larger than that of LiNi0.8Co0.2O2. The SEM images indicated that the powders of the material were submicron size. The results of the ICP-AES analysis proved that elemental compositions of the material were similar to those of the targeted one. Cyclic voltammetry （3.0- 4. 2 V） illustrated that the new material had good lithium-ion intercalation/de-intercalation performance. The results of galvanostatic cycling showed that the initial specific discharge capacity of the prepared material was 181.4 mAh/g, and the specific discharge capacity was 177.3 mAh/g after 100 cycles （0. 2C, 3.0 - 4. 2 V, vs. Li^＋/Li） with the capacity retention ratio of 97.7%.展开更多
W-doped Li4TisO12 in the form of Li4Ti4.95W0.osO12 was firstly synthesized via solid state reaction. X-ray diffraction （XRD） and scanning electron microscope （gEM） were employed to characterize the structure and m...W-doped Li4TisO12 in the form of Li4Ti4.95W0.osO12 was firstly synthesized via solid state reaction. X-ray diffraction （XRD） and scanning electron microscope （gEM） were employed to characterize the structure and morphology of Li4Ti4.psW0.05Ol2. W-doping does not change the phase composition and particle morphology, while remarkably improves its cycling stability at high charge/discharge rate. Li4Ti4.95W0.05O12 exhibits an excellent rate capability with a reversible capacity of 131.2 mA.h/g at 10C and even 118.6 mA.h/g at 20C. The substitution of W for Ti site can enhance the electronic conductivity of Li4TisO12 via the generation of mixing Ti4＋/Ti3＋, which indicates that Li4Ti4.psW0.05O12 is promising as a high rate anode for the lithium-ion batteries.展开更多
In order to explore the most suitable mode for the primary processing model of reconstituted tobacco, another two kinds of conditioning process schemes for reconstituted tobacco were designed based on the existing rec...In order to explore the most suitable mode for the primary processing model of reconstituted tobacco, another two kinds of conditioning process schemes for reconstituted tobacco were designed based on the existing reconstituted tobacco processing method. Comparative analysis and evaluation were conducted for moisture content uniformity, intrinsic chemical compositions, casing uniformity, blending uniformity and sensory quality of the samples from the three kind of processing modes. The results showed that loosing and conditioning or the vacuum conditioning pretreatment of the reconstituted tobacco could effectively reduce the difference in moisture content during the blending, and improve the casing uniformity and blending uniformity. Moreover, the samples with the loosing and conditioning pretreatment had higher total sugar and reducing sugar contents, which indicated that the loosing and conditioning pretreatment method was more favorable for the improvement of the intrinsic quality of cigarettes. In addition, the three kinds of aromatic components contents of cigarettes using the loosing and conditioning pretreatment were higher,and the casing uniformity, blending uniformity and overall sensory quality of this pretreatment were all superior to that of the other two kinds of reconstituted tobacco pretreatment methods. The contents of total sugar, reducing sugar as well as the three kinds of aromatic components of cigarettes processed with vacuum conditioning pretreatment were all slightly lower than those of the existing methods, but the casing uniformity and blending uniformity were improved, while it showed small difference in the sensory quality with the existing processing method.展开更多
The F-doped O3-type NaNi1/3Fe1/3Mn1/3O2-xFx （x = 0, 0.005, 0.01,002 and noted as NFM-F0, NFM-F0.005, NFM-F0.01, NFM-F0.02, respectively, united as NFM-Fs） cathode materials were investigated systematically. The rate...The F-doped O3-type NaNi1/3Fe1/3Mn1/3O2-xFx （x = 0, 0.005, 0.01,002 and noted as NFM-F0, NFM-F0.005, NFM-F0.01, NFM-F0.02, respectively, united as NFM-Fs） cathode materials were investigated systematically. The rate performance and capacity retention of the O3-type cathode materials are significantly improved as a function of specific F-doping levels. Optimum performance is achieved in the NFM-F0.01 material having a capacity of -110mAhg-1 at a current density of 150mAg-1 after 70 cycles. The results indicate that the binding energy of oxygen changes as a result of F-doping, and in addition, F-doping results in changes to the stoichiometry of Mn3＋/Mn4＋, which stabilizes the O3-type layered structure, thus allowing cycling performance to be improved. However, NFM-F0.02, having a higher F-doping level, retains a high capacity retention, although a slight loss is observed. The results suggest there is an optimum F-doping level for the NFM-F system to deliver enhanced cycling performance.展开更多
Transition metal phosphides have been explored as promising active materials for sodium-ion batteries(SIBs)and hydrogen evolution reaction(HER) applications owing to their unique physical and chemical characteristics....Transition metal phosphides have been explored as promising active materials for sodium-ion batteries(SIBs)and hydrogen evolution reaction(HER) applications owing to their unique physical and chemical characteristics. However,they suffer from the drawbacks such as severe agglomeration,and sluggish reaction kinetics. Herein, bimetallic phosphides(Ni2 P/Zn P4) embedded in P-doped carbon hierarchical microspheres are demonstrated with robust structural integrity,fast charge transfer, and abundant active sites. As expected,the optimally structured Ni2 P/Zn P4 composite exhibits good electrochemical performance as an anode material in SIBs,including high specific capacity, good cycling stability and rate capability. Meanwhile, the Ni2 P/Zn P4 composite also exhibits excellent electrocatalytic performance for HER with a small overpotential of 62 m V, a Tafel slope of 53 m V dec^-1, as well as excellent stability.展开更多
基金Project(E2015202356)supported by the Natural Science Foundation of Hebei Province,ChinaProject(2013009)supported by the Technology Innovation Foundation for Outstanding Youth of Hebei University,China
文摘Pristine LiNi0.5Mn1.5O4and Na-doped Li0.95Na0.05Ni0.5Mn1.5O4cathode materials were synthesized by a simple solid-statemethod.The effects of Na+doping on the crystalline structure and electrochemical performance of LiNi0.5Mn1.5O4cathode materialwere systematically investigated.The samples were characterized by XRD,SEM,FT-IR,CV,EIS and galvanostatic charge/dischargetests.It is found that both pristine and Na-doped samples exhibit secondary agglomerates composed of well-defined octahedralprimary particle,but Na+doping decreases the primary particle size to certain extent.Na+doping can effectively inhibit the formationof LixNi1-xO impurity phase,enhance the Ni/Mn disordering degree,decrease the charge-transfer resistance and accelerate the lithiumion diffusion,which are conductive to the rate capability.However,the doped Na+ions tend to occupy8a Li sites,which forces equalamounts of Li+ions to occupy16d octahedral sites,making the spinel framework less stable,therefore the cycling stability is notimproved obviously after Na+doping.
基金Project(51572300) supported by the National Natural Science Foundation of China。
文摘The conversion reaction-based anode materials of sodium ion batteries have relatively high capacity;however,the application of these materials is limited by their structural collapse due to the poor structure stability.In this work,MoSe_(2) nanosheets were synthesized by a solvothermal method.An organic solvent was intercalated into the MoSe_(2) materials to enlarge the interlayer spacing and improve the conductivity of the material.The MoSe_(2) material was coated with an organic pyrolysis carbon and then a uniform carbon layer was formed.The surface carbon hybridization of the nanosheet materials was realized by the introduction of heteroatoms during the sintering process.The as-prepared MoSe_(2)@N,P-C composites showed a superior rate performance as it could maintain the integrity of the morphology and structure under a high current density.The composites had a discharge specific capacity of 302.4 mA·h/g after 100 cycles at 0.5 A/g,and the capacity retention rate was 84.96%.
基金Project(2014CB643406)supported by the National Basic Research Program of China
文摘A series of layered LiNi0.8?xCo0.1Mn0.1LaxO2(x=0,0.01,0.03)cathode materials were synthesized by combining co-precipitation and high temperature solid state reaction to investigate the effect of La-doping on LiNi0.8Co0.1Mn0.1O2.A new phase La2Li0.5Co0.5O4was observed by XRD,and the content of the new phase could be determined by Retiveld refinement and calculation.The cycle stability of the material is obviously increased from74.3%to95.2%after La-doping,while the initial capacity exhibits a decline trend from202mA·h/g to192mA·h/g.The enhanced cycle stability comes from both of the decrease of impurity and the protection of newly formed La2Li0.5Co0.5O4,which prevents the electrolytic corrosion to the active material.The CV measurement confirms that La-doped material exhibits better reversibility compared with the pristine material.
基金the Natural Science Foundation of Heilongjiang, China(Grant No.E2004-24).
文摘LiNi0.78 Co0.2 Al0.02O2 cathode materials were prepared with a novel co-precipitation method followed by heat-treating. The properties of the materials were characterized. XRD patterns showed that no secondary phase appeared and the hexagonal lattice parameter c of LiNi0.rsCoo.2AI^0202 was larger than that of LiNi0.8Co0.2O2. The SEM images indicated that the powders of the material were submicron size. The results of the ICP-AES analysis proved that elemental compositions of the material were similar to those of the targeted one. Cyclic voltammetry （3.0- 4. 2 V） illustrated that the new material had good lithium-ion intercalation/de-intercalation performance. The results of galvanostatic cycling showed that the initial specific discharge capacity of the prepared material was 181.4 mAh/g, and the specific discharge capacity was 177.3 mAh/g after 100 cycles （0. 2C, 3.0 - 4. 2 V, vs. Li^＋/Li） with the capacity retention ratio of 97.7%.
文摘W-doped Li4TisO12 in the form of Li4Ti4.95W0.osO12 was firstly synthesized via solid state reaction. X-ray diffraction （XRD） and scanning electron microscope （gEM） were employed to characterize the structure and morphology of Li4Ti4.psW0.05Ol2. W-doping does not change the phase composition and particle morphology, while remarkably improves its cycling stability at high charge/discharge rate. Li4Ti4.95W0.05O12 exhibits an excellent rate capability with a reversible capacity of 131.2 mA.h/g at 10C and even 118.6 mA.h/g at 20C. The substitution of W for Ti site can enhance the electronic conductivity of Li4TisO12 via the generation of mixing Ti4＋/Ti3＋, which indicates that Li4Ti4.psW0.05O12 is promising as a high rate anode for the lithium-ion batteries.
基金Supported by the Fund of Chinese Tobacco Enterprises(MK-JS-2012-129)~~
文摘In order to explore the most suitable mode for the primary processing model of reconstituted tobacco, another two kinds of conditioning process schemes for reconstituted tobacco were designed based on the existing reconstituted tobacco processing method. Comparative analysis and evaluation were conducted for moisture content uniformity, intrinsic chemical compositions, casing uniformity, blending uniformity and sensory quality of the samples from the three kind of processing modes. The results showed that loosing and conditioning or the vacuum conditioning pretreatment of the reconstituted tobacco could effectively reduce the difference in moisture content during the blending, and improve the casing uniformity and blending uniformity. Moreover, the samples with the loosing and conditioning pretreatment had higher total sugar and reducing sugar contents, which indicated that the loosing and conditioning pretreatment method was more favorable for the improvement of the intrinsic quality of cigarettes. In addition, the three kinds of aromatic components contents of cigarettes using the loosing and conditioning pretreatment were higher,and the casing uniformity, blending uniformity and overall sensory quality of this pretreatment were all superior to that of the other two kinds of reconstituted tobacco pretreatment methods. The contents of total sugar, reducing sugar as well as the three kinds of aromatic components of cigarettes processed with vacuum conditioning pretreatment were all slightly lower than those of the existing methods, but the casing uniformity and blending uniformity were improved, while it showed small difference in the sensory quality with the existing processing method.
基金supported by the National High-Tech R&D Program of China (2015AA034601, 2016YFB010030X, and 2016YFB0700600)the State Key Laboratory of Materials Processing and Die & Mould Technologythe Analytical and Testing Center of Huazhong University of Science Technology
文摘The F-doped O3-type NaNi1/3Fe1/3Mn1/3O2-xFx （x = 0, 0.005, 0.01,002 and noted as NFM-F0, NFM-F0.005, NFM-F0.01, NFM-F0.02, respectively, united as NFM-Fs） cathode materials were investigated systematically. The rate performance and capacity retention of the O3-type cathode materials are significantly improved as a function of specific F-doping levels. Optimum performance is achieved in the NFM-F0.01 material having a capacity of -110mAhg-1 at a current density of 150mAg-1 after 70 cycles. The results indicate that the binding energy of oxygen changes as a result of F-doping, and in addition, F-doping results in changes to the stoichiometry of Mn3＋/Mn4＋, which stabilizes the O3-type layered structure, thus allowing cycling performance to be improved. However, NFM-F0.02, having a higher F-doping level, retains a high capacity retention, although a slight loss is observed. The results suggest there is an optimum F-doping level for the NFM-F system to deliver enhanced cycling performance.
基金supported by the National Natural Science Foundation of China (51872334, 51874362 and 51572299)the Innovation-Driven Project of Central South University (2017CX001 and 2018CX004)the Natural Science Foundation of Hunan Province,China (2018JJ1036)
文摘Transition metal phosphides have been explored as promising active materials for sodium-ion batteries(SIBs)and hydrogen evolution reaction(HER) applications owing to their unique physical and chemical characteristics. However,they suffer from the drawbacks such as severe agglomeration,and sluggish reaction kinetics. Herein, bimetallic phosphides(Ni2 P/Zn P4) embedded in P-doped carbon hierarchical microspheres are demonstrated with robust structural integrity,fast charge transfer, and abundant active sites. As expected,the optimally structured Ni2 P/Zn P4 composite exhibits good electrochemical performance as an anode material in SIBs,including high specific capacity, good cycling stability and rate capability. Meanwhile, the Ni2 P/Zn P4 composite also exhibits excellent electrocatalytic performance for HER with a small overpotential of 62 m V, a Tafel slope of 53 m V dec^-1, as well as excellent stability.
