To investigate the process optimizationof Cu-en/AP composite microspheres preparation via electrostatic spraying,and to reveal the effects of droplet properties and flow rate variations on the experimental results dur...To investigate the process optimizationof Cu-en/AP composite microspheres preparation via electrostatic spraying,and to reveal the effects of droplet properties and flow rate variations on the experimental results during the electrostatic spraying process,the prepared process parameters of Cu-en/AP composite microspheres by electrostatic spray method under the orthogonal experimental design simulated by ANSYS(Fluent).The influence of flow rate,solvent ratio,and solid mass on the experimental results is examined using a controlled variable method.The results indicate that under the conditions of a flow rate of 2.67×10^(-3)kg/s an acetone-to-deionized water ratio of 1.5∶1.0,and a solid mass of 200 mg,the theoretical particle size of the composite microspheres can reach e nanoscale.Droplet trajectories in the electric field remain stable without significant deviation.The simulation results show that particle diameter decreases with increasing flow rate,with the trend leveling off around a flow rate of 1×10^(-3)kg/s.As the solvent ratio increases(with higher acetone content),particle diameter initially decreases,reaching a minimum around a ratio of 1.5∶1.0 before gradually increasing.Increasing the solid mass also reduces the particle diameter,with a linear increase in diameter observed at around 220 mg.Cu-en/AP composite microspheres with nanoscale dimensions were confirmed under these conditions by the final SEM images.展开更多
The present study deals with the Water Quality Index （WQI） and absorption of zinc from electroplating industry effluent using ftmgi. The physico-chemical parameters such as EC （Electrical Conductivity）, TDS （Tota...The present study deals with the Water Quality Index （WQI） and absorption of zinc from electroplating industry effluent using ftmgi. The physico-chemical parameters such as EC （Electrical Conductivity）, TDS （Total Dissolved Solids）, total hardness, magnesium, calcium, chloride, sodium, potassium, nickel, chromium and zinc content was above the permissible limits of BIS （Bureau of Indian Standards）. The WQI was 13, which showed that the pollution level of the electroplating industry effluent was severe in the rating scale and the effluent was not suitable for disposal without treatment. Three fungal species such as Aspergillus niger, Peinicillium chrysogenum and Rhizopus nigricans were used for absorption studies. Different concentrations （25, 50, 75 and 100%） of electroplating industry effluent along with 1 gm of fungal mycelium with （1%） and without carbon source was incubated in a shaker for a period of 7 days in order to observe zinc absorption capacity. The absorption capacity of zinc was found to be higher in Aspergillus niger followed by Rhizopus nigricans and Penicillium chrysogenum. Among the three fungal species Aspergillus niger had high （50%） potential of zinc absorption with carbon source and low concentration （25%） of electroplating industry effluent.展开更多
基金National Natural Science Foundation of China(No.2275150)。
文摘To investigate the process optimizationof Cu-en/AP composite microspheres preparation via electrostatic spraying,and to reveal the effects of droplet properties and flow rate variations on the experimental results during the electrostatic spraying process,the prepared process parameters of Cu-en/AP composite microspheres by electrostatic spray method under the orthogonal experimental design simulated by ANSYS(Fluent).The influence of flow rate,solvent ratio,and solid mass on the experimental results is examined using a controlled variable method.The results indicate that under the conditions of a flow rate of 2.67×10^(-3)kg/s an acetone-to-deionized water ratio of 1.5∶1.0,and a solid mass of 200 mg,the theoretical particle size of the composite microspheres can reach e nanoscale.Droplet trajectories in the electric field remain stable without significant deviation.The simulation results show that particle diameter decreases with increasing flow rate,with the trend leveling off around a flow rate of 1×10^(-3)kg/s.As the solvent ratio increases(with higher acetone content),particle diameter initially decreases,reaching a minimum around a ratio of 1.5∶1.0 before gradually increasing.Increasing the solid mass also reduces the particle diameter,with a linear increase in diameter observed at around 220 mg.Cu-en/AP composite microspheres with nanoscale dimensions were confirmed under these conditions by the final SEM images.
文摘The present study deals with the Water Quality Index （WQI） and absorption of zinc from electroplating industry effluent using ftmgi. The physico-chemical parameters such as EC （Electrical Conductivity）, TDS （Total Dissolved Solids）, total hardness, magnesium, calcium, chloride, sodium, potassium, nickel, chromium and zinc content was above the permissible limits of BIS （Bureau of Indian Standards）. The WQI was 13, which showed that the pollution level of the electroplating industry effluent was severe in the rating scale and the effluent was not suitable for disposal without treatment. Three fungal species such as Aspergillus niger, Peinicillium chrysogenum and Rhizopus nigricans were used for absorption studies. Different concentrations （25, 50, 75 and 100%） of electroplating industry effluent along with 1 gm of fungal mycelium with （1%） and without carbon source was incubated in a shaker for a period of 7 days in order to observe zinc absorption capacity. The absorption capacity of zinc was found to be higher in Aspergillus niger followed by Rhizopus nigricans and Penicillium chrysogenum. Among the three fungal species Aspergillus niger had high （50%） potential of zinc absorption with carbon source and low concentration （25%） of electroplating industry effluent.
