农业灌溉磁化水器的研制和开发

用磁化水灌溉可增加蔬菜、粮食、水果、经济作物产量的科学实验已被国内外证实。增产粮食10%,蔬菜10%—15%,黑木耳35%、水果12%—15%。以前此项目没有得到开发的原因是:1.设计的磁化水实验设备均使用电磁,要生产磁场需耗费大量电能,在用电紧张的情况下,难以实现。2.没有设计出系列的磁化水器,

柴油机进气管喷水节油机理研究

本文提出在柴油机进气管上，安装一个特制的不锈钢化水器，用它喷出一定量的雾化水，参与气缸内燃烧，可提高柴油机的性能．根据柴油机的工况，可以控制所需的较佳喷水量．这套系统经过发动机台装试验与拖拉机实用作业试验表明：喷水节油率达到３％以上，标定功率提高０．５ＰＳ，排气温度下降１０～２０℃，ＮＯｘ降低３０ｇｋｇ－１．喷水试验，在拖拉机上进行了５００ｈ的负荷作业，实测小时节油为０．０６ｋｇ／ｈ，拆机检查，零部件磨损正常，无锈蚀，积炭少，油底壳内机油无水。

Study on Piggery Anaerobic Fermentation Slurry Treated by Anoxic/Oxic Process

[Objective] The aim of this study was to provide a fast, stable and efficient piggery wastewater processing technology. [Method] The start-up process was studied through the experiment of piggery anaerobic fermentation slurry treated by Anoxic/Oxic （A/O） reactor. The process was divided into two stages： at the first stage, dominant micro flora were cultivated in Anoxic and Oxic reaction tanks respectively; at the second stage. Anoxic and Oxic reaction tanks were initiated jointly to gradually enhance water load and continued to cultivate and domesticate microorganisms, and finally the start-up process was completed. [ Result] The results showed that return mixture ratio and return sludge ratio was 2 and 1 respectively when the temperature reached 32 ±2 ℃. However. when aeration rate of Oxic reaction amounted to 0.5 m^3/h, the re- moval rate of COD and NH4^＋ -H were 89.87% and 89.31% respectively through practical operation within 50 days, which indicated that the start- up process through A/O reactor was successful. Conclusion This study can provide a scientific basis and reference for innocuous technique of piggery anaerobic fermentation slurry treatment.

Measurement of Concentration of Sorbent Particles and Water Droplets in Hydration Desulfurization Reactor with PIV

Vortexing limestone injection into furnace combined with calcium lime hydration in the downstream is the most promising technology for controlling SO 2 emission. Particle imaging velocimetry (PIV) is used to measure the gas liquid solid three phase flow field in a reactor. By image processing based on newly developed software, the number concentrations of sorbent particles and water droplets are presented. The measuring results are very helpful for better understanding the desulfurization mechanism and optimizing configurational and operational parameters in the hydration reactor.

Feasibility analysis of SO_2 absorption using a hydrophilic ceramic membrane contactor

Hydrophilic ceramic membranes would be potential candidates for membrane gas absorption if they could be applied to appropriate separation processes.This study highlights a novel concept for the practical implementation of SO_2 absorption in hydrophilic ceramic membrane that exhibits outstanding thermal and mechanical stabilities.With this aim,we investigated experimentally the performance of SO_2 absorption into aqueous sodium hydroxide (NaOH) solution in a hydrophilic alumina (Al_2O_3) membrane contactor in terms of SO_2 removal efficiency and SO_2 mass transfer flux,and compared the performance with that in a hydrophobic one.A series of experiments were performed at various conditions over a NaOH concentration range of 0–1.0 mol·L^(-1),a liquid flow rate range of 30–180 ml·min^(-1),a gas flow rate range of 120–1000 ml·min^(-1),an inlet SO_2 concentration range of 400–2000μl·L^(-1),and a temperature range of 10–35°C.It was found that the hydrophilic membrane was more competitive when using a NaOH concentration higher than 0.2 mol·L^(-1).Furthermore,it can be inferred that the hydrophilicα-Al_2O_3 membrane exhibited exceptional long-term stability under 480 h continuous operation.

Improved S Surface Controller and Semi-physical Simulation for AUV

S surface controllers have been proven to provide effective motion control for an autonomous underwater vehicle (AUV).However, it is difficult to adjust their control parameters manually.Choosing the optimum parameters for the controller of a particular AUV is a significant challenge.To automate the process, a modified particle swarm optimization (MPSO) algorithm was proposed.It was based on immune theory, and used a nonlinear regression strategy for inertia weight to optimize AUV control parameters.A semi-physical simulation system for the AUV was developed as a platform to verify the proposed control method, and its structure was considered.The simulation results indicated that the semi-physical simulation platform was helpful, the optimization algorithm has good local and global searching abilities, and the method can be reliably used for an AUV.

Tissue engineering for neuromuscular disorders of the gastrointestinal tract

The digestive tract is designed for the optimal processing of food that nourishes all organ systems.The esophagus,stomach,small bowel,and colon are sophisticated neuromuscular tubes with specialized sphincters that transport ingested food-stuffs from one region to another.Peristaltic contractions move ingested solids and liquids from the esophagus into the stomach;the stomach mixes the ingested nutrients into chyme and empties chyme from the stomach into the duodenum.The to-and-fro movement of the small bowel maximizes absorption of fat,protein,and carbohydrates.Peristaltic contractions are necessary for colon function and defecation.

Nitrous Oxide Production in a Sequence Batch Reactor Wastewater Treatment System Using Synthetic Wastewater

The rate of nitrous oxide emission from a laboratory sequence batch reactor （SBR） wastewater treatment system using synthetic wastewater was measured under controlled conditions. The SBR was operated in the mode of 4 h for aeration, 3.5 h for stirring without aeration, 0.5 h for settling and drainage, and 4 h of idle. The sludge was acclimated by running the system to achieve a stable running state as chemical oxygen demand, NO2^-, NO3^-, NH4^＋, pH, and N2O. indicated by rhythmic changes of total N, dissolved oxygen, Under the present experimental conditions measured nitrous oxide emitted from the off-gas in the aerobic and anaerobic phases, respectively, accounted for 8.6%-16.1% and 0-0.05% of N removed, indicating that the aerobic phase was the main source of N2O emission from the system. N2O dissolved in discharged water was considerable in term of concentration. Thus, measures to be developed for the purpose of reducing N2O emission from the system should be effective in the aeration phase.

A Novel Multi-Tube Photoreactor with UV Light and Immobilized TiO_2 Thin Film for Water Treatment

A novel multi-tube photoreactor with 0.0188m3 valid reaction volume was constructed in pilot-scale. This rectangular reactor consisted of 13 regularly distributed silica glass tubes coating with TiO2 thin film photo-catalyst. Total active area of TiO2 thin film is 0.3916m2. The ratio of surface area to volume achieves 20.8m-1. Photocatalytic experiment of phenol red demonstrates that the apparent reaction rate constant (k) is 0.074 65 h-1 and 0.16502h-1 for reaction system with and without micro-bubbles mixing. The corresponding apparent quantum efficiency (a) is 8.1771 X 10-7g.J-1 and 4.9036 x 10-7g-J-1, respectively. COD value of reactant could decrease to 17mg.L-1 and high performance liquid chromatography (HPLC) only shows two absorption peaks in 24 h pho-tocatalytic process time, so this photoreactor has good photomineralization effect. Experimental results reveal that photocatalytic destruction of organics is possible by using the multi-tube photoreactor.

NECK LEAF 1, a GATA type transcription factor, modulates organogenesis by regulating the expression of multiple regulatory genes during reproductive development in rice

In the monocot rice species Oryza sativa L., one of the most striking morphological processes during reproductive development is the concurrence of panicle development with the sequential elongation of upper internodes （UPIs）. To elucidate the underlying molecular mechanisms, we cloned the rice gene NECK LEAF 1 （NL1）, which when mutated results in delays in flowering time, smaller panicles with overgrown bracts and abnormal UPI elongation patterns. The NL1 gene encodes a GATA-type transcription factor with a single zinc finger domain, and its transcripts are de- tected predominantly in the bract primordia, which normally degenerate in the wild-type plants. Overexpression of NL1 in transgenic plants often gives rise to severe growth retardation, less vegetative phytomers and smaller leaves, suggesting that NL1 plays an important role in organ differentiation. A novel mutant allele of PLASTOCHRON1 （PLAD, a gene known to play a key role in regulating leaf initiation, was identified in this study. Genetic analysis demonstrated an interaction between nil and plal, with NL1 acting upstream of PLA1. The expression level and spatial pattern of PLA1 were found to be altered in the nil mutant. Furthermore, the expression of two regulators of flowering, Hd3a and OsMADS1, was also affected in the nil mutant. On the basis of these findings, we propose that NL1 is an intrinsic factor that modulates and coordinates organogenesis through regulating the expression of PLA1 and other regulatory genes during reproductive development in rice.

Effects of nutrients and light intensity on the growth and biochemical composition of a marine microalga Odontella aurita

Algal biotechnology has advanced greatly in the past three decades. Many microalgae are now cultivated to produce bioactive substances. Odontella aurita is a marine diatom industrially cultured in outdoor open ponds and used for human nutrition. For the first time, we have systematically investigated the effects of culture conditions in cylindrical glass columns and fiat-plate photobioreactors, including nutrients （nitrogen, phosphorus, silicon, and sulfur）, light intensity and light path, on O. aurita cell growth and biochemical composition （protein, carbohydrate, β-1,3-glucan, lipids, and ash）. The optimal medium for photoautotrophic cultivation of O. aurita contained 17.65 mmol/L nitrogen, 1.09 mmol/L phosphorus, 0.42 mmol/L silicon, and 24.51 mmol/L sulfur, yielding a maximum biomass production of 6.1-6.8 g/L and 6.7-7.8 g/L under low and high light, respectively. Scale-up experiments were conducted with fiat-plate photobioreactors using different light-paths, indicating that a short light path was more suitable for biomass production of O. aurita. Analyses of biochemical composition showed that protein content decreased while carbohydrate （mainly composed of 15-1,3-glucan） increased remarkably to about 50% of dry weight during the entire culture period. The highest lipid content （19.7% of dry weight） was obtained under 0.11 mmol/L silicon and high light conditions at harvest time. Fatty acid profiles revealed that 80% were Cx4, C^6, and C20, while arachidonic acid and eicosapentaenoic acid （EPA） accounted for 1.6%-5.6% and 9%-20% of total fatty acids, respectively. High biomass production and characteristic biochemical composition profiles make O. aurita a promising microalga for the production ofbioactive components, such as EPA and D-1,3-glucan.

Speciation of chromium in soil inoculated with Cr(Ⅵ)-reducing strain,Bacillus sp.XW-4

Cr(Ⅵ)-amended soil was inoculated with Cr(Ⅵ)-reducing strain,Bacillus sp.XW-4 and incubated at 28 ℃in an incubator. Cr(Ⅵ)reduction,available Cr and Cr fractionin soils were studied.The results show that addition of Bacillus sp.XW-4 can promote Cr(Ⅵ)reduction,but inoculation of this strain has a negative effect on the decrease of available Cr content in soil.In controls (without this strain)amended with 100 and 200 mg/kg of Cr(Ⅵ),Cr(Ⅵ)contents decrease to about 41 and 92 mg/kg respectively after incubation of 4 d,while in soil inoculated with XW-4,Cr(Ⅵ)contents decrease to about 18 and 60 mg/kg,respectively.The content of available Cr in soils with inoculation of XW-4 is higher than that in controls.Chromium is partitioned into water soluble Cr,exchangeable Cr,precipitated Cr,Cr bound to organics and residual Cr.The highest content of Cr is observed in residual form and water soluble Cr is not detected for all treatments after 42 d,but the soils inoculated with Bacillus sp.XW-4 contain higher content of exchangeable Cr and lower content of precipitated Cr than the soil without the inoculum.Inoculation of Bacillus sp.XW-4 can increase chromium activity in soils.

Detecting hydrosonic signal using a polarization technique

Some optical fiber hydrophones, such as PGC Mach-Zehnder Interferometer, have a birefringence of single mode optical fibers which induce signal fading. Especially, if two optical beams from the optical arms are orthogonal, the interferomic signal can’t be detected at all. Here a new method is introduced. This is to translate the detected phase difference into a linearly polarized angle, then detect it, so that polarization inducing signal fading will be avoided. In theory, this problem is solved. Furthermore, the effect on measurement results from optical source fluctuation becomes little when using the polarization technique.

Improving performance of flat plate solar collector using nanofluid water/zinc oxide

In this article,the effect of using water/zinc oxide nanofluid as a working fluid on the performance of solar collector is investigated experimentally.The volumetric concentration of nanoparticles is 0.4%,and the particle size is 40 nm,and the mass flow rate of the fluid varies from 1 to 3 kg/min.For this experiment,a device has been prepared with appropriate measuring instruments whose energy source is solar radiation.The solar energy absorbed by the flat plate collector is absorbed by the nanofluid of water/zinc oxide.The nanofluid is pumped to the consumer,a heat exchanger,where it heats the water.The temperature,radiation level,flow rate,and pressure in different parts of the device were measured.The pressure drop and the heat transferred are the most important results of this experimental work.The ASHRAE standard is used to calculate efficiency.The results showed that the use of water/zinc oxide nanofluid increases the collector performance compared to water.For 1 kg/min of mass flow rate,the nanofluids have a 16% increase in efficiency compared to water.From the results,it can be concluded that the choice of optimum mass flow rate in both water and nanofluid cases increases efficiency.

Optimal design of heat exchanger header for coal gasification in supercritical water through CFD simulations

Heat exchangers play an important role in supercritical water coal gasification systems for heating feed and cooling products. However, serious deposition and plugging problems always exist in heat exchangers. CFD modeling was used to simulate the transport characteristics of solid particles in supercdtical water through the shell and tube of heat exchangers to alleviate the problems. In this paper, we discuss seven types of exchangers CA, B, C D, E, F and G）, which vary in inlet nozzle configuration, header height, inlet pipe diameter and tube pass distribution. In the modeling, the possibility of deposition in the header was evaluated by accumulated mass of particles; we used the velocity contour of supercritical water （SCW） to evaluate the uniformity of the velocity dis- tribution among the tube passes. Simulation results indicated that the optimum heat exchanger had structure F, which had a rectangular configuration of tube pass distractions, a bottom inlet, a 200-mm header height and a 10-ram inlet pipe diameter.

Synergetic effects for p-nitrophenol abatement using a combinedactivated carbon adsorption-electrooxidation process

A novel fluidized electrochemical reactor that integrated advanced electrochemical oxidation with activated carbon (AC) fluidization in a single cell was developed to model pollutant p-nitrophenol (PNP) abatement. AC fluidization could enhance COD removal by 22%-30%. In such a combined process, synergetic effects on PNP and COD removal was found, with their removal rate being enhanced by 137.8% and 97.8%, respectively. AC could be electrochemically regenerated and reused, indicating the combined process would be promising for treatment of biorefractory organic pollutants.

Influence of Temperature, Water Quality and Collector Type on Flotation Performance of a Peruvian Phosphate Ore

The sedimentary phosphate deposit of Bayovar is located in a very dry area of Peru （desert of Sechura） which is close to the Pacific coast. It consists of seven superposed layers （beds） which call for different strategy of concentration. The ore is composed predominantly by apatite （84% in weight basis） plus silicates （16%）. To concentrate phosphate from beds 6-7, it is necessary to carry out further cationic reverse flotation of silicates, at neutral pH, to yield a concentrate which meets market specification. The new process was developed in laboratory scale by a collaborative program conducted between Vale S. A. and the University of Sao Paulo--Brazil. As water resources are very limited at Bayovar region, all the steps of concentration, including flotation, must be performed with seawater which must be continuously recycled. This work addresses some relevant topics related to the use of seawater in the reverse cationic flotation of silicates： influence of temperature, water quality （ageing and chemical composition） and collector type. The results indicate that amido amine works better than ether amine. If flotation is conducted with the former collector, the separation process is able to tolerate changes in temperature （25 ℃-40 ℃） and water quality caused by either evaporation or ageing.

PW-3A型喷雾着水调质机及其应用

主要介绍PW - 3A型喷雾着水调质机、超低量雾化旋转喷水器的应用及其主要技术参数、工艺效果和操作要求。

Simulation and Design Optimization of Ammonia Synthesis Converter

One-dimensional pseudo-homogeneous model of an axial flow converter and one-dimensional heteroge-neous model of a horizontal converter have been presented, which describe the distribution of gaseous composition,temperature and pressure along the height in the two converters, respectively. Design optimization methods of the two converters have been proposed, by which the minimum catalyst volume can be obtained to satisfy the productive capacity of 1000 tons per day, when the operating pressure is 15.0, 10.0 and 7.5 MPa, respectively.

Effects of Anthropogenic Disturbance on Sediment Organic Carbon Mineralization Under Different Water Conditions in Coastal Wetland of a Subtropical Estuary

The changes in soil organic carbon(C) mineralization as affected by anthropogenic disturbance directly determine the role of soils as C source or sink in the global C budget. The objectives of this study were to investigate the effects of anthropogenic disturbance(aquaculture pond, pollutant discharge and agricultural activity) on soil organic C mineralization under different water conditions in the Minjiang River estuary wetland, Southeast China. The results showed that the organic C mineralization in the wetland soils was significantly affected by human disturbance and water conditions(P < 0.001), and the interaction between human disturbance activities and water conditions was also significant(P < 0.01). The C mineralization rate and the cumulative mineralized carbon dioxide-carbon(CO_2-C)(at the 49th day) ranked from highest to lowest as follows: Phragmites australis wetland soil > aquaculture pond sediment > soil near the discharge outlet > rice paddy soil. This indicated that human disturbance inhibited the mineralization of C in soils of the Minjiang River estuary wetland, and the inhibition increased with the intensity of human disturbance. The data for cumulative mineralized CO_2-C showed a good fit(R^2 > 0.91) to the first-order kinetic model C_t = C_0(1 – exp(–kt)). The kinetic parameters C_0, k and C_0 k were significantly affected by human disturbance and water conditions. In addition, the total amount of mineralized C(in 49 d) was positively related to C_0, C_0 k and electrical conductivity of soils. These findings indicated that anthropogenic disturbance suppressed the organic C mineralization potential in subtropical coastal wetland soils, and changes of water pattern as affected by human activities in the future would have a strong influence on C cycling in the subtropical estuarine wetlands.