Enhanced photocatalytic performance of cementitious material with TiO_2@Ag modified fly ash micro-aggregates

A TiO2 photocatalyst is coated on the surface of a zeolite fly ash bead（ZFAB） to improve its dispersability and exposure degree in a cement system.The application of Ag particles in TiO2/ZFAB modified cementitious materials is to further enhance the photocatalytic performance.Various Ag@TiO2/ZFAB modified cementitious specimens with different Ag dosages are prepared and the characteristics and photocatalytic performance of the prepared samples are investigated.It is observed that the multi-level pore structure of ZFAB can improve the exposure degree of TiO2 in a cement system and is also useful to enhance the photocatalytic efficiency.With an increment of the amounts of Ag particles in the TiO2/ZFAB modified cementitious samples,the photocatalytic activities increased first and then decreased.The optimal Ag@TiO2/ZFAB modified cementitious sample reveals the maximum reaction rate constant for degrading benzene（9.91×10^-3 min^-1）,which is approximately 3 and 10 times higher than those of TiO2/ZFAB and TiO2 modified samples,respectively.This suggests that suitable Ag particles coupled with a ZFAB carrier could effectively enhance the photocatalytic effects and use of TiO2 in a cement system.Thus,ZFAB as a carrier could provide a potential method for a high efficiency engineering application of TiO2 in the construction field.

Fabrication of β-Sialon/ZrN/ZrON composites using fly ash and zircon

β-Sialon/ZrN/ZrON composites were successfully fabricated by an in-situ carbothermal reduction？nitridation process with fly ash, zircon and active carbon as raw materials. The effects of raw materials composition and holding time on synthesis process were investigated, and the formation process of the composites was also discussed. The phase composition and microstructure of the composites were characterized by means of XRD and SEM. It was found that increasing carbon content in a sample and holding time could promote the formation of β-Sialon, ZrN and ZrON. The proper processing parameters to synthesize β-Sialon/ZrN/ZrON composites were mass ratio of zircon to fly ash to active carbon of 49：100：100, synthesis temperature of 1550 °C and holding time of 15 h. The average grain size ofβ-Sialon and ZrN（ZrON） synthesized at 1550 °C for 15 h reached about 2 and 1μm, respectively. The fabrication process ofβ-Sialon/ZrN/ZrON composites included the formation ofβ-Sialon and ZrO2 as well as the conversion of ZrO2 to ZrN and ZrON.

Application of pre-alloyed powders for diamond tools by ultrahigh pressure water atomization

Copper, iron and cobalt based pre-alloyed powders for diamond tools were prepared by ultrahigh pressure water atomization（UPWA） process. Pre-alloyed powders prepared by different processes including UPWA, conventional water atomization （CWA） and elemental metal mechanical mixing （EMMM） were sintered to segments and then compared in mechanical properties, holding force between matrix and diamond, fracture morphology of blank and sintering diamond section containing matrix. The results showed that the pre-alloyed powder prepared by UPWA exhibits the best mechanical properties including the relative density, the hardness and the bending strength of matrix sinteredsegment. Sintered segments fractography of UPWA pre-alloyed powder indicatesmechanical mosaic strength and chemical bonding force between the pre-alloyed powder and the diamond, leading to the great increase in the holding force between matrix and diamond. The mechanical performance andthe service life of diamond tools were greatly improved by UPWA pre-alloyed powders.

解放“上帝

解放“上帝＂崔金生服务业商业等爱称顾客为﹃上帝﹄刚戴这顶高帽时觉得挺美虽说﹃上帝﹄并不能真的主宰一切但在这顶高帽下顾客的地位有了一定提高毕竟是好事不过现在的﹃上帝﹄在假冒伪劣商品泛滥的今天却越来越感到难当到市场商场买东西要货比三家...

A Green and Mild Approach of Synthesis of Highly-Conductive Graphene Film by Zn Reduction of Exfoliated Graphite Oxide

We report a simple and green approach to synthesize reduced graphene oxide （RGO） nanosheets at room temperature based on Zn reduction of exfoliated GO. The evolution of GO to RGO has been characterized by X-ray diffraction, UV-Vis absorption spectroscopy and Raman spectroscopy. The results of X-ray photoelectron spectroscopy reveal that the atomic ratio of carbon to oxygen in the RGO can be tuned from 1.67 to 13.7 through controlling the reduction time. Moreover, the conductivity of the RGO is measured to be 26.9±2.2 kS/m, much larger than those previously obtained by chemical reduction through other reducing agents. More importantly, the resistance of the RGO film with 20 nm thickhess can be as low as 2 kΩ/square, while a high transparency over 70% within a broad spectral range from 0.45 pm to 1.50 p.m can be retained. The proposed method is low-cost, eco-friendly and highly-eiffcient, the as-prepared thinner RGO films are useful in a variety of potential application fields such as optoelectronics, photovoltaics and electrochemistry by serving as an ultralight, flexible and transparent electrode material.

Preparation and sintering properties of zirconia-mullite-corundum composites using fly ash and zircon

Zirconia-mullite-corundum composites were successfully prepared from fly ash,zircon and alumina powder by a reaction sintering process.The phase and microstructure evolutions of the composite synthesized at desired temperatures of 1 400,1 500 and 1 600°C for 4 h were characterized by X-ray diffractometry and scanning electronic microscopy,respectively.The influences of sintering temperature on shrinkage ratio,apparent porosity and bulk density of the synthesized composite were investigated.The formation process of the composites was discussed in detail.The results show that the zirconia-mullite-corundum composites with good sintering properties can be prepared at 1 600°C for 4 h.Zirconia particles can be homogeneously distributed in mullite matrix,and the zirconia particles are around 5μm.The formation process of zirconia-mullite-corundum composites consists of decomposition of zircon and mullitization process.

Pollen and Phytolith Analyses of Ancient Paddy Fields at Chuodun Site, the Yangtze River Delta

A number of paddy fields pertaining to the Majiabang Cultures (5500-3800 years BC) were discovered during the archaeological excavations that were carried out since 1998 at the Chuodun site in the Yangtze River Delta. The pollen and phytolith analyses of two soil profiles from the northeastern part of this site were carried out to trace the agricultural practices of the Neolithic period. The phytolith results showed that rice domestication in the Yangtze River Delta could be traced back to as early as the Majiabang Culture. The pollen assemblage also revealed low levels of aquatic species, similar to that in modern paddy fields. This finding suggested that humans might have removed weeds for rice cultivation during the Neolithic period. Thus, pollen analysis in association with phytolith analysis was a promising method for identifying ancient paddy fields.

Talc-bearing serpentinized peridotites from the southern Mariana forearc:implications for aseismic character within subduction zones

The serpentinized peridotites overlying the subducted zones in the Izu-Bonin-Mariana(IBM) arc system have been interpret as the cause of the low-velocity layer identified beneath the IBM froearc,in turn few earthquakes occurred along the plate boundary.Chrysotile,which is a low temperature and highly hydrated phase of serpentine with low frictional strength,has been suggested as the low velocity material in the serpentinized peridotites,besides,brucite is inferred to be likely conducive to stable sliding.However,such idea encounters challenging in our serpentinized peridotites from the southern Mariana forearc,which absent both the above minerals.The presence of talc,which characterized by its weak,low-friction and inherently stable sliding behavior,provides new clue.Here we report the occurrence of talc in serpentinized peridotites collected from the landward trench slope of the southern Mariana forearc.We infer that talc is mainly forming as a result of the reaction of serpentine minerals with silica-saturated fluids released from the subducting slab,and talc also occurs as talc veins sometimes.Due to its unique physical properties,talc may therefore play a significant role in aseismic slip in the IBM subduction zone.

Silica-alumina molar ratio and some factors effect on the synthesis of zeolites from fly ash

In order to improve the activity and eliminate some impurities, pretreatment was used before hydrothermal synthesis. The fly ash was mixed with an aqueous NaOH solution, the alkali melted fly ash was also adopted, which is hydrothermally treated at about 104 ℃, and the liquid/solid ratio was controlled at 6：1. In order to control Si/Al molar ratio, SiO2 or Al2O3 powers were added to the fly ash. The results of XRD and SEM show that the alkali melted can activate fly ash and eliminate its quartz and mullite, along with the improvement of Si/Al molar ratio and alkalinity. In addition, zeolite Na-A changes into sodalite gradually, and nepheline is the synthesized intermediate product. Those results were discussed on the basis of a formation mechanism of zeolite from fly ash.

Evaluation of graphite depressants in a poly-metallic sulfide flotation circuit

Synthetic dyes are commonly used for graphite depression in poly-metallic flotation circuits; however,these dyes can be very expensive. The aim of this study is to evaluate performance of certain low-cost alternative depressants for a complex lead-zinc(Pb-Zn) ore rich in graphite(Gr-C) on a conventional mini pilot-scale flotation circuit. The reagents used were commercial and industrial grade starch; agro-based waste-sugarcane bagasse and charred(burnt) bagasse powder. The primary evaluation criteria were quality(grades) of lead and zinc concentrates, their recoveries(%), and graphite rejection(%) in the tails.Benchmark tests using nigrosine as graphite depressant showed 94.3% rejection of Gr-C. The results with commercial starch were found as effective with 93.8% graphite rejection. Furthermore, bagasse powder showed potential in improving product quality(36.4% and 65.6% Pb grade and recovery) with an intermediate effectiveness in graphite rejection(85.6%). The order of effectiveness in Gr-C rejection follows nigrosine % commercial starch > bagasse > industrial starch > charred bagasse. In addition, the effect these depressants on silver(byproduct) grade and recovery was also investigated.

New material of Cordaites baodeensis Sun from Lower Permian Shanxi Formation of Baode,Shanxi

Based on the anatomical study of leaf cuticles of Cordaites from the Lower Permian Shanxi Formation in Baode of Shanxi, the author analysed the epidermal characters of Cordaites in this area. On the base of the abundant compressions and laboratory studies, the author complemented some new data of the cuticular characters of the speeies Cordaites baodeensis Sun for its study of taxonomy. Meanwhile, the author newly discovered a number of sporopollen fossils associated with the mega-plants of Cordctitales, described 9 species of 6 genera. The palynological data can provide a supplement evidence for defining the age of C. baodeensis and its associated plants to be Early Permian.

Botanical Study on Early Cretaceous Coal-Bearing Strata in Northeast China and Inner Mongolia, China

Study on the fossil plants and the palynological assemblage is the basic botanical research on the coal bearing strata. The practice indicate that comprehensive data from the study on the fusinized wood fossil, the phyterals and the analysis of dispersed cuticles will effectively improve the level of the study on the coal bearing strata as a whole.

Talc-Based Concrete for Sealing Borehole Optimized by Using Particle Packing Theory

The paper describes assessment of the performance of cement-poor concretes on the basis of packing theory. The concretes are intended for sealing segments of deep boreholes and have a small amount of cement for minimizing the mutual chemical impact on the contacting clay seals. The composition is examined by application of packing theory with respect to the cement/aggregate ratio and the gradation of the aggregate material which is crushed quartzite for providing high internal friction after maturation, as well as to talc added for fluidity and to the small amount of cement. Low porosity and micro-structural stability must be guaranteed for very long periods of time. The study exemplifies how packing theory assist designers in selecting optimal proportions of the various components. Optimum particle packing implies minimizing the porosity and thereby reducing the amount of cement paste needed to fill the voids between the aggregate particles. The use of talc as inorganic super-plasticizer since ordinary organic additives for reaching high fluidity at casting are undesirable, and since talc reacts with cement and provides high strength in along-term perspective.

Preparation of diamond/Cu microchannel heat sink by chemical vapor deposition

A Ti interlayer with thickness about 300 nm was sputtered on Cu microchannels, followed by an ultrasonic seeding with nanodiamond powders. Adherent diamond film with crystalline grains close to thermal equilibrium shape was tightly deposited by hot-filament chemical vapor deposition(HF-CVD). The nucleation and growth of diamond were investigated with micro-Raman spectroscope and field emission scanning electron microscope(FE-SEM) with energy dispersive X-ray detector(EDX). Results show that the nucleation density is found to be up to 1010 cm-2. The enhancement of the nucleation kinetics can be attributed to the nanometer rough Ti interlayer surface. An improved absorption of nanodiamond particles is found, which act as starting points for the diamond nucleation during HF-CVD process. Furthermore, finite element simulation was conducted to understand the thermal management properties of prepared diamond/Cu microchannel heat sink.

Regulation of Talcum Powder in Cosmetics at Home and Abroad

The article introduced the toxicological information of talcum powder, analyzed the relevant requirements on talcum powder in cosmetics and the impurity asbestos in China, the EU, the US, and Canada, and the safety of the substance is also evaluated to help regulators and relevant enterprises understand its hazards and to promote consumers' awareness of talcum powder.

Effects of Nano Silica, Micro Silica, Fly Ash and Bottom Ash on Compressive Strength of Concrete

In this study, SCM （supplementary cementitious materials）, such as nano silica, micro silica, fly ash and bottom ash, have been evaluated for optimal level of replacement as blending material in cement and concrete. The physical and chemical properties of the above materials were first analyzed. This study focused on compressive strength of concrete with different mixes at different ages. In many cases, products made with fly ash, micro silica, nano silica and bottom ash perform better than products made without them. Test results obtained in this study indicate that up to 5% nano silica, 10% micro silica, 20-30% fly ash and 10% bottom ash could be advantageously blended with cement without adversely affecting the strength. However, optimum levels of these materials are 1-3% nano silica, 3-8% micro silica, 10% fly ash and 5% of bottom ash when we consider the strength of concrete. All percentages are defined by weight unless otherwise mentioned.

Relationship between Landslides, Geologic Structures, and Hydrothermal Alteration Zones in the Ohekisawa-Shikerebembetsugawa Landslide Area, Hokkaido, Japan

This paper elucidates the relationship between landslides, geologic structures, and hydrothermal alteration zones based primarily on X-ray powder diffraction and uniaxial compressive strength tests on weakly weathered and hydrothermally altered rocks from the Ohekisawa-Shikerebembetsugawa landslide area in Teshikaga Town, Hokkaido, Japan. The OHS （Ohekisawa slide） occurred on a dip slope of sedimentary rocks from the Upper Miocene Shikerepe Formation within a homocline, and also on weathered and hydrothermally altered rocks within the boundary area between the hydrothermal smectite zone and smectite-bearing mordenite zone. The SHS （Shikerebembetsugawa slide） occurred on a dip slope of sedimentary rocks from the Upper Miocene Hanakushibe Formation within wavy folds and was also controlled by a cap rock of Teshikaga Volcano Somma Lava. The SHS occurred also on weathered and hydrothermally altered rocks within the boundary area between the hydrothermal smectite zone and smectite-bearing laumontite zone. The mechanical properties of smectite, smectite-bearing mordenite, and smectite-bearing laumontite zone weakly weathered rocks indicate that they are very weak, soft rocks. These landslides are regarded as HAZLs （hydrothermal alteration zone landslides）. The hydrothermal alteration yielding smectite is thus closely related to these two ancient landslides, suggesting that the potential for HAZLs within a hydrothermal area can be assessed based on the swelling clay mineral-beating hydrothermal alteration types, dip slope, and cap rock.

Fabrication and characterization of graphene derived from SiC

Using novel ideas for the fabrication of epitaxial graphene （EG） on SiC, two forms of graphene termed as vertical aligned gra- phene sheets （VAGS） and graphene covered SiC powder （GCSP） were derived, respectively, from SiC slices and SiC powder, aimed for applications in energy storage and photocatalysis. Herein, the fabrication procedures, morphology characteristics, some intrinsic physical properties and performances for applications in field effect transistor （FET） and cold cathode field emission source are revealed and analyzed based on the graphene materials. The EG on a 2-inch SiC （0001） showed an average sheet resistance about 720 D,/~5 with a non-uniformity 7.2%. The FETs fabricated on the EG possessed a cutoff frequency 80 GHz. Based on the VAGS derived from a completely carbonized SiC slice, a magnetic phase diagram of graphene with irregu- lar zigzag edges is also reported.