热处理对硅酸盐玻璃化稳性的影响

玻璃经存贮一段时间或经水洗脱碱并经热处理,则表面化稳性能有很大增加,这主要是由于低碱水化层经不可逆脱水玻璃表面水润湿性大为降低。热处理温度应取决于玻璃表面水润湿性大小所决定的不可逆脱水温度。

掺Y_2O_3磷酸盐隔热玻璃的制备及其性质的研究

以磷酸盐为主要原料,通过掺Y2O3制得了具有良好化学稳定性和可见光透过性的磷酸盐隔热玻璃。测定了玻璃的XRD、穆斯堡尔谱、IR光谱及可见一缸外光谱,并对Y2O3改善磷酸盐玻璃的机制进行了合理的解释。

Preparation and Characterization of ZnO-CuO-Bi_(2)O_(3)-B_(2)O_(3)-SiO_(2)System Low Melting Sealing Glasses

Lead-free low melting glasses,ZnO-CuO-Bi_(2)O_(3)-B_(2)O_(3)-SiO_(2)system,with fixed contents of 15 mol%CuO and 20 mol%Bi_(2)O_(3),were prepared by using melt cooling method.Structure and thermal properties of the glasses were studied by using X-ray diffractometer(XRD),infrared spectrometer(FIT-IR),thermal dilatometer and differential thermal analyzer(DTA).Chemical durability of the glasses was studied by using dissolution rate method.Wettability of glasses on substrate was tested by using button sintering experiment.It is found that alkaline resistance of the glass solders is lower than that of plate glass and the water resistance is comparable with that of plate glass.The sealing temperatures are Ts=445-490℃,while the average thermal expansion coefficient from room temperature to 300℃is in the range of(65-82)×10^(−7)℃^(−1).At sealing temperature,the glass solders have good wettability on plate glass or alumina substrate.They are not crystallized even sintered at the sealing temperature for 30 min.The solder glasses are suitable for sealing plate glass,alumina and other inorganic non-metallic materials.

Strength and plasticity improvement induced by strong grain refinement after Zr alloying in selective laser-melted AlSiMg1.4 alloy

In order to enhance the mechanical properties of the selective laser-melted(SLM) high-Mg content AlSiMg1.4 alloy,the Zr element was introduced.The influence of Zr alloying on the processability,microstructure,and mechanical properties of the alloy was systematically investigated through performing microstructure analysis and tensile testing.It was demonstrated that the SLM-fabricated AlSiMg1.4-Zr alloy exhibited high process stability with a relative density of over 99.5% at various process parameters.Besides,the strong grain refinement induced by the primary Al3Zr particle during the melt solidification process simultaneously enhanced both the strength and plasticity of the alloy.The values for the yield strength,ultimate tensile strength,and elongation of the SLM-fabricated AlSiMg1.4-Zr were(343±3) MPa,(485±4) MPa,and(10.2±0.2)%,respectively,demonstrating good strengthplasticity synergy in comparison to the AlSiMg1.4 and other Al-Si-based alloys fabricated by SLM.

Improvement in Performance of Carbon-based Perovskite Solar Cells through Interface Modification with CTAC

Carbon-based perovskite solar cells have attracted much attention,due to their low cost,simple preparation process and high chemical stability.However,the devices exhibit low photoelectric conversion efficiency,owing to the presence of defects and interface impedance between the perovskite active layer and the contact interface.In order to minimize the interfacial defects and improve the charge transfer performance between the perovskite layer and the contact interface,cetyltrimethylammonium chloride(CTAC)was introduced into the lower interface of HTL-free carbon-based perovskite solar cells,because CTAC can be used as interface modification material to passivate the buried interface of perovskite and promote grain growth.It was found that CTAC can not only passivate the interface defects of perovskite,but also improve the crystalline quality of perovskite.As a result,the photovoltaic conversion efficiency of reaches 17.18%,which is 12.5%higher than that of the control group.After 20 days in air with 60%RH humidity,the cell can still maintain more than 90%of the initial efficiency,which provides a new strategy for interfacial passivation of perovskite solar cells.

Skin care efficacy study of recombinant humanized collagen based on in vitro level

Studying the skin care efficacy of recombinant humanized collagen based on in vitro level.The stability of the recombinant humanized collagen was first analyzed by treating at different temperatures,then its skincare efficacy based on in vitro level was evaluated by detecting the inhibition rate of elastase,the inhibition rate of collagenase,the protein content of type I collagen in human fibroblasts,the inhibition of reactive oxygen species(ROS)with human keratinocytes,and the effects of the recombinant humanized collagen on the expression of hyaluronic acid(HA),filaggrin(FLG)and transglutaminase 1(TGM1)in keratinocytes.The results showed that recombinant humanized collagen was able to maintain stability at temperatures below 70℃.With regard to its skincare efficacy,recombinant humanized collagen could inhibit elastase and collagenase activities and promote the increase of type I collagen content in human fibroblasts.It also showed good inhibition of ROS in keratinocytes in vitro and could increase the expression of HA,FLG,and TGM1 in keratinocytes.In short,the recombinant humanized collagen exhibited a favourable skin care effect in vitro level.This study proved that it has potential firming,anti-wrinkle,moisturizing,and repairing efficacy,and is a valuable cosmetic raw material.

Single atom gold catalysts for low-temperature CO oxidation

Low‐temperature CO oxidation is important for both fundamental studies and practical applica‐tions. Supported gold catalysts are generally regarded as the most active catalysts for low‐temperature CO oxidation. The active sites are traditionally believed to be Au nanoclusters or nanoparticles in the size range of 0.5–5 nm. Only in the last few years have single‐atom Au catalysts been proved to be active for CO oxidation. Recent advances in both experimental and theoretical studies on single‐atom Au catalysts unambiguously demonstrated that when dispersed on suitable oxide supports the Au single atoms can be extremely active for CO oxidation. In this mini‐review, recent advances in the development of Au single‐atom catalysts are discussed, with the aim of illus‐trating their unique catalytic features during CO oxidation.

Synthesis,characterization and photocatalytic performance of rod-shaped Pt/PbWO_4 composite microcrystals

Rod-shaped PbW O4 microcrystals of length 1 μm were fabricated by a hydrothermal route and subsequent calcination. Pt nanoparticles（NPs） of different contents（0.5 wt%,1 wt% and 2 wt%） were subsequently deposited on the PbW O4 microcrystals,producing robust Pt/PbW O4 composite microcrystals. The PbW O4 microcrystals and Pt/PbW O4 photocatalysts were characterized by X-ray diffraction,N2 sorption measurements,scanning electron microscopy,transmission electron microscopy,and X-ray photoelectron,photoluminescence,Fourier-transform infrared,and ultraviolet-visible diffuse reflectance spectroscopies. The photocatalytic performances of the catalysts were evaluated by the consecutive photocatalytic degradation of acid orange II dye. The Pt/PbW O4 composite microcrystals exhibited high photocatalytic activity and stability. The deposition of Pt NPs produced surface plasmon resonance（SPR）,which induced a large visible light absorption. A Pt NP content of 1-2 wt% resulted in an ~2 times increase in photocatalytic activity,compared with the activity of Pt/PbW O4. The crystal structure and high crystallinity of PbW O4 resulted in its favorable photocatalytic property,and the SPR effect of the Pt NPs promoted visible light harvesting. The Pt NPs also enhanced the separation of photo-generated electrons and holes,which further promoted the photocatalytic reaction.

PtSnNa/SUZ-4:An efficient catalyst for propane dehydrogenation

The structure and catalytic properties of PtSn catalysts supported on SUZ-4 and ZSM-5 zeolite have been studied by using various experimental techniques including XRD,nitrogen adsorption,NH3-TPD,TG,H2-TPR and TPO techniques combined with propane dehydrogenation tests.It has been shown that SUZ-4-supported PtSnNa（PtSnNa/SUZ-4） was determined to be a better catalyst for propane dehydrogenation than conventional catalysts supported on ZSM-5,owing to its higher catalytic activity and stability.Dibenzothiophene poisoning experiments were performed to investigate the detailed structures of the two supported catalysts.The characterization of the two catalysts indicates that the distribution of Pt on the porous support affects the activity.In contrast to ZSM-5-supported catalysts,Pt particles on the PtSnNa/SUZ-4 are primarily dispersed over the external surface and are not as readily deactivated by carbon deposition.This is because that the strong acid sites of the SUZ-4 zeolite evidently prevented the impregnation of the Pt precursor H_2PtCl_6 into the zeolite.In contrast,the weak acid sites of the ZSM-5 zeolite led to more of the precursor entering the zeolite tunnels,followed by transformation to highly dispersed Pt clusters during calcination.In the case of the PtSnNa/ZSM-5,the interactions between Sn oxides and the support were lessened,owing to the weaker acidity of the ZSM-5 zeolite.The dispersed Sn oxides were therefore easier to reduce to the metallic state,thus decreasing the catalytic activity for hydrocarbon dehydrogenation.

A CMOS Fully Integrated Frequency Synthesizer with Stability Compensation

A complete closed-loop third order s-domain model is analyzed for a frequency synthesizer. Based on the model and root-locus technique, the procedure for parameters design is described, and the relationship between the process,voltage,and temperature variation of parameters and the loop stability is quantitatively analyzed. A variation margin is proposed for stability compensation. Furthermore,a simple adjustable current cell in the charge pump is proposed for additional stability compensation and a novel VCO with linear gain is adopted to limit the total variation. A fully integrated frequency synthesizer from 1 to 1.05GHz with 250kHz channel resolution is implemented to verify the methods.

Preparation of TiO2/Bi2O3 Microfibers and Their Photocatalytic Activity

A series of TiO2/Bi2O3 heterojunction microfibers have been fabricated using cotton fibers as bio-templates, and characterized by XRD, SEM and UV-Vis techniques. Results reveal that Bi2O3 in the TiO2/Bi2O3 sample is assigned to monoclinic and tetragonal mix-crystal phase. Fibers lengths can reach several micrometers and diameters range from 0.5 μm to 3 μm. Compared with pure TiO2 and Bi2O3, TiO2/Bi2O3 samples display better absorption in visible light region. Photocatalytic activity was evaluated by degradation of MB under visible light irradiation. TiO2/Bi2O3 microfibers exhibite much higher activity than pure TiO2 and Bi2O3, and 22.84%TiO2/Bi2O3 can achieve the decomposition of about 95%MB, which is attributed to synergistic effects of the strong visible-light absorption of TiO2/Bi2O3 microfibers and the heterojunction formed between TiO2 and Bi2O3.

Fluidization characteristics of magnetic particles and determination of stable fluidization zone in magnetically fluidized bed

To determine and calculate the stable fluidization zone in a magnetically fluidized bed, the fluidization characteristics of magnetic particles are investigated. Four kinds of magnetic particles with different average diameters, ranging from 231 to 512 μm, are fluidized in the presence of magnetic fields with specified values of the intensity in the range of zero to 7330 A/m, and the particle fluidization curves are plotted. For marking the stable fluidization zone in the curves, the minimum bubbling velocities of particles are measured by the pressure-drop fluctuation. Based on the fluidization curves, the influences of the average particle diameter and magnetic field intensity on the zone are analyzed and discussed. A correlation to determine the stable fluidization zone is derived from the experimental data, using three dimensionless numbers, i. e., the ratio of magnetic potential to gravity potential, the Reynolds number and the Archimedes number. Compared with available data reported, it is shown that the correlation is more simplified to predict relative parameters for the bed operating in the state of stable fluidization under reasonable conditions.

Photosynthesis of Resurrection Angiosperms

Resurrection plants which are able to quickly reactivate after falling into a period of anabiosis caused by dehydration have been very rare among angiosperms, especially among dicotyledons whose chlorophyll content and chloroplast structure little changed in the course of desiccation, therefore has been called homoiochlorophyllous desiccation-tolerant plants (HDTs). Another type of resurrection angiosperms that lost its chlorophyll dining desiccation is called poikilochlorophyllous desiccation-tolerant plants (PDTs). HDTs have been received more attention because of simplicity of protection mechanism which is much easy to the study and utilization of the desiccation tolerance of resurrection angiosperms. Recent advances in studies of photosynthesis of resurrection angiosperms indicate that photochemical activities are sensitive indicators for the study of physiological state of resurrection angiosperms during desiccation and rehydration. Photochemical activities of resurrection angiosperms are inhibited with loss of water similar to those of general plants, however, the magic thing is that they could reactivate rapidly during rehydration even losing more than 95% water. Up-regulations in xanthophyll cycle and antioxidative systems as well as preservation in integrity and stability of photosynthetic membranes during desiccation may be very important to desiccation tolerance of resurrection angiosperms. The fact that phosphate treatment in rehydration stage also strongly influences resurrection indicated importance of studies on rehydration stages of resurrection angiosperms.

Influence of Si on stability of TiC in Al melts

The influence of Si on the stability of TiC in Al melts was studied.It is found that TiC particles in Al melts become unstable with the addition of Si.When the melting temperature is below 890 °C,TiC will react with Al and Si to form TiAlxSiy and Al4C3 phases.But if the melt temperature is above 890 ℃,TiC will react with Al and Si to form to Ti3SiC2 and Al4C3.It is considered that the influence of Si on the stability of TiC in Al melts is due to its incursion into TiC crystal lattice during the holding,which will cause serious lattice distortion in TiC and then speed up the out-diffusion of surrounded C atoms.

Study on ternary polymerization of toluene diisocyanate

For the production of reactive polyurethane cross-linkinger and curing agents, 2, 4-diisocyanate toluene （TDI） terpolymer, which possesses the rigid structures of hexatomic ring and three reactive functional groups, was synthesized and characterized by the Fourier transform infrared （FFIR）, the gel permeation chromatography （GPC） and the chemical analysis methods. The reaction conditions were studied and optimized. A tracking research on the polymerization process of TDI was taken by using the GPC. The formation processes of the terpolymer, oligomers and higher-polymers were also dealt with. Results show that the TDI terpolymer can be prepared in the presence of Cat-3 catalyst and at the reaction temperature of （60 ±2）℃. The reaction time is short, its outcomes have narrow molecular weights distribution, namely molecular weights from 530 to 550, Mw/Mn =1.10, and the mass fraction of NCO is （25. 0 ± 0. 5）%. With the reaction time prolonging, however, TDI can be further higher-polymedzed to form higher-polymers. Benzoyl chloride （0. 4%, mass fraction）, as the stabilizing agent, can effectively inhibit the occurrence of higher-polymerization. The obtained TDI terpolymer can be stable for more than half a year.

A first-principles study on elastic properties and stability of Ti_xV_(1-x)C multiple carbide

The structure,stability and elastic properties of di-transition-metal carbides TixV1-xC were investigated by using the first-principles with a pseudopotential plane-waves method.The results show that the equilibrium lattice constants of TixV1-xC show a nearly linear reduction with increasing addition of V.The elastic properties of TixV1-xC are varied by doping with V.The bulk modulus of Ti0.5V0.5C is larger than that of pure TiC,as well as Ti0.5V0.5C has the largest C44 among TixV1-xC（0≤x≤1）,indicating that Ti0.5V0.5C has higher hardness than pure TiC.However,Ti0.5V0.5C presents brittleness based on the analysis of ductile/brittle behavior.The Ti0.5V0.5C carbide has the lowest formation energy,indicating that Ti0.5V0.5C is more stable than all other alloys.

Stable Control of Influence Factor during Two-phase Anaerobic Digestion for Agricultural Organic Waste

Two-phase anaerobic digestion process is influenced by acid control for hydrogen production, reaction temperature, substrate detention time, sludge activity, and granular formation. Al of these technological parameters are directly related to success or failure of the system operation and treatment effect.

NOVEL METHOD FOR DYNAMIC OPTIMIZATION OF STABILITY IN HIGH-SPEED MILLING SYSTEM

Considering the self-excited and forced vibrations in high-speed milling processes, a novel method for dynamic optimization of system stability is used to determine the cutting parameters and structural parameters by increasing the chatter free material removal rate （CF-MRR） and surface finish. The method is hased on the theory of the chatter stability and the semi-bandwidth of the resonant region. The objective function of the method is material removal rate（MRR）,the constraints are chatter stability and surface finish, and the optimizing variables are cutting and structural parameters. The optimization procedure is stated. The method is applied to a milling system and CF-MRR is increased 18.86%. It is shown that the influences of the chatter stability and the resonance are simultaneously considered in the dynamic optimization of the milling system for increasing CF-MRR and the surface finish.

Influence of heat treatment on electrochemical properties of Ti_(1.4)V_(0.6)Ni alloy electrode containing icosahedral quasicrystalline phase

The structures and electrochemical properties of the Ti1.4V0.6Ni ribbon before and after heat treatment are investigated systematically. The structure of the sample is characterized by X-ray powder diffraction analysis. Electrochemical properties including the discharge capacity, the cyclic stability and the high-rate discharge ability are tested. X-ray powder diffraction analysis shows that after heat treatment at 590 °C for 30 min, all samples mainly consist of the icosahedral quasicrystal phase (I-phase), Ti2Ni phase (FCC), V-based solid solution phase (BCC) and C14 Laves phase (hexagonal). Electrochemical measurements show that the maximum discharge capacity of the alloy electrode after heat treatment is 330.9 mA?h/g under the conditions that the discharge current density is 30 mA/g and the temperature is 30 °C. The result indicates that the cyclic stability and the high-rate discharge ability are all improved. In addition, the electrochemical kinetics of the alloy electrode is also studied by electrochemical impedance spectroscopy (EIS) and hydrogen diffusion coefficient (D).

Effect of Molybdenum Doping on Oxygen Permeation Properties and Chemical Stability of SrCo0.8Fe0.2O3-δ

The phase composition, microstructure, thermal expansion coefficients, oxygen permeation properties and chemical stability of SrCo0.8Fe0.2O3-δ （SCFM） were investigated and compared with those of SrCo0.8Fe0.2O3-δ（SCF）. Single phase SCFM was successfully prepared by a combined EDTA-citric method. SCFM shows a lower thermal expansion coefficient （24× 10^-6-29× 10^-6/K） than SCF between 500 and 1050 ℃, indicating a more stable structure. SCFM shows a high oxygen permeation flux, although the oxygen flux of SCFM decreases slightly because of Mo dopant. Furthermore, it was demonstrated that the doping of Mo in SCF can prevent the order-disorder transition and improves the chemical stability to CO2.