期刊文献+
共找到17篇文章
< 1 >
每页显示 20 50 100
基于非线性互补问题函数的半光滑牛顿最优潮流算法 被引量:35
1
作者 张永平 童小娇 +3 位作者 吴复立 严正 倪以信 陈寿孙 《中国电机工程学报》 EI CSCD 北大核心 2004年第9期130-135,共6页
提出了一种新的基于非线性互补问题(NCP)函数的半光滑牛顿办法,以用于求解最优潮流(OPF)问题。通过引入NCP函数,将OPF模型KKT条件的互补松弛约束转化为等 约束,并采用非光滑牛顿法求解。算法的突出优势在于能够有效地处理OPF模型中的不... 提出了一种新的基于非线性互补问题(NCP)函数的半光滑牛顿办法,以用于求解最优潮流(OPF)问题。通过引入NCP函数,将OPF模型KKT条件的互补松弛约束转化为等 约束,并采用非光滑牛顿法求解。算法的突出优势在于能够有效地处理OPF模型中的不等式约束,从而完全避免了OPF计算中起作用的不等式约束的识别问题。同时,文中利用电力系统的弱耦合特性,构造了牛顿分解算法。IEEE多个算例的数值试验表明:提出的算法具有很好的收敛特性和计算效果,有很好的实际应用前景。 展开更多
关键词 电力系统 非线性互补问题 NCP函数 光滑牛顿最优潮流算法
下载PDF
半步偏差-几何最优法插补直线、圆弧软件的研究 被引量:4
2
作者 薛峰 夏金兵 尹志强 《机床与液压》 北大核心 2003年第6期112-113,266,共3页
根据半步偏差 -几何最优法三条基本的插补原则 :轮廓线分类原则、走步原则和偏差原则 ,推导出直线、圆弧的偏差以及半步偏差的计算公式。并在此基础上确定程序框图。编制的数控机床插补软件是按Microsoft宏汇编建立的程序 ,可在 80 86... 根据半步偏差 -几何最优法三条基本的插补原则 :轮廓线分类原则、走步原则和偏差原则 ,推导出直线、圆弧的偏差以及半步偏差的计算公式。并在此基础上确定程序框图。编制的数控机床插补软件是按Microsoft宏汇编建立的程序 ,可在 80 86系列的微处理机上执行 ,能对平面直线、圆弧进行插补。 展开更多
关键词 插补 数控机床 步偏差-几何最优 直线 圆弧 数控加工
下载PDF
沙尘预报客观检验中最优实况资料和圆插值半径选择研究 被引量:2
3
作者 孟庆涛 《气候与环境研究》 CSCD 北大核心 2019年第6期735-740,共6页
使用2012~2014年每年3~5月CUACE(China Meteorological Administration Unified Atmospheric Chemistry Environment)模式地面沙尘浓度格点预报产品,预报员预报等级产品、实况地面观测沙尘等级和特征站观测PM10(空气动力学当量直径小于... 使用2012~2014年每年3~5月CUACE(China Meteorological Administration Unified Atmospheric Chemistry Environment)模式地面沙尘浓度格点预报产品,预报员预报等级产品、实况地面观测沙尘等级和特征站观测PM10(空气动力学当量直径小于等于10μm的颗粒物,即可吸入颗粒物)资料,并针对CUACE模式格点产品,选取不同半径对格点产品进行圆插值,从而对2012~2014年共25次沙尘过程值,采取3年总样本计算TS(Threat Score)评分,对格点产品适合的圆插值半径和预报产品适合的检验实况资料进行研究,结论如下:(1)如实况采用沙尘等级,模式插值半径与TS评分在浮尘或扬沙等级成近似线性下降关系,而在沙尘暴以上等级TS评分与插值半径关系几乎不大,最优插值半径可选为最小插值半径0.5°(经度/纬度);如实况采用PM10资料,TS评分在浮尘或扬沙等级根据半径不同变化较为剧烈,沙尘暴以上等级TS评分与插值半径关系不大,可以采用浮尘或扬沙平均线3.5°为平均最优插值半径。如果沙尘过程较弱,插值半径可适当减小,以1°最合适;(2)对CUACE模式预报产品,沙尘等级观测TS评分可用性要优于PM10资料,但两者在沙尘暴以上等级评分差别不大,总体上CUACE模式最优检验实况资料可选为沙尘等级观测资料。对预报员沙尘预报产品,观测沙尘等级TS评分要远高于PM10,预报员沙尘预报产品最优检验实况资料为观测沙尘等级资料。 展开更多
关键词 沙尘 检验 圆插值 最优插值 适合检验实况资料
下载PDF
基于VaR风险控制的半log-最优资产组合模型 被引量:3
4
作者 宋博 陈守东 《统计与信息论坛》 CSSCI 2010年第5期21-24,共4页
通过建立基于VaR风险控制下的单周期半log-最优资产组合数学模型,证明了最优解的存在性与唯一性。利用遗传算法对半log-最优资产组合模型进行了实例计算与分析,并与log-最优资产组合模型进行了比较,结果表明半log-最优资产组合模型具有... 通过建立基于VaR风险控制下的单周期半log-最优资产组合数学模型,证明了最优解的存在性与唯一性。利用遗传算法对半log-最优资产组合模型进行了实例计算与分析,并与log-最优资产组合模型进行了比较,结果表明半log-最优资产组合模型具有计算方便的特征。 展开更多
关键词 VaR(value at risk) log-最优资产组合 风险控制 遗传算法
下载PDF
WDM网络中的一个改进的最优半光通道路由算法 被引量:1
5
作者 余国松 王强 夏尊铨 《应用数学》 CSCD 北大核心 2002年第4期67-71,共5页
本文在一个限定的条件下 ,提出了一个WDM网络中的寻找最优半光通道算法 ,使时间复杂度从O(k2 n +km+knlog(kn) )提高到O(k2 n +km+nlogn)
关键词 WDM网络 最优光通道 路由算法 图论 光网络
下载PDF
基于最优发射半径的锥形线圈WPT系统优化 被引量:1
6
作者 王红 荆凡胜 李颖 《电气传动》 2021年第24期57-62,共6页
在无线电能传输系统中盘式发射线圈存在一个使传输功率最大的最优半径值,并且传输距离的改变也会造成发射线圈最优半径值的变化。针对这一问题,提出了量化发射线圈最优半径与传输距离关系的方法,继而指导发射线圈的优化设计。首先从系... 在无线电能传输系统中盘式发射线圈存在一个使传输功率最大的最优半径值,并且传输距离的改变也会造成发射线圈最优半径值的变化。针对这一问题,提出了量化发射线圈最优半径与传输距离关系的方法,继而指导发射线圈的优化设计。首先从系统空间磁场的分析上,证明了最优发射半径的存在性,然后探究并拟合出最优发射半径与传输距离之间的表达式,设计了每匝线圈半径均为最优值的锥形螺旋发射线圈。最后经有限元仿真验证,优化的锥形线圈系统较传统的柱形线圈系统互感提升了140.16%,周围环境的漏磁更少,证明了优化的锥形螺旋线圈的优越性。 展开更多
关键词 无线电能传输 最优发射 锥形螺旋线圈 柱形螺旋线圈 传输性能
下载PDF
延长油田富指油区储层裂缝与井网系统关系及最优裂缝半长研究
7
作者 王杨 张鹏 +1 位作者 刘柯 段晓辉 《辽宁化工》 CAS 2013年第3期297-299,共3页
裂缝性低渗透砂砾岩油藏普遍蕴藏于鄂尔多斯盆地三叠系储层中。裂缝的发育、形态以及分布情况已经成为制约油田有效开发的关键因素之一。在长期生产实践中,裂缝形态与井网系统的匹配关系以及油田生产后期水力压裂裂缝半长的定量化预测... 裂缝性低渗透砂砾岩油藏普遍蕴藏于鄂尔多斯盆地三叠系储层中。裂缝的发育、形态以及分布情况已经成为制约油田有效开发的关键因素之一。在长期生产实践中,裂缝形态与井网系统的匹配关系以及油田生产后期水力压裂裂缝半长的定量化预测研究逐渐成为油藏开发不可或缺的部分。该文通过对裂缝进行数值模拟研究,确定了裂缝发育的三种形态所对应的三种最佳的井网形式并选择5种方案模拟裂缝,从而得出最佳的人工裂缝半长。 展开更多
关键词 延长油田 裂缝 井网系统 最优裂缝
下载PDF
最小、最大广义最优停止规则的特征
8
作者 金治明 《国防科技大学学报》 EI CAS CSCD 北大核心 1990年第3期58-62,共5页
设(X<sub>n</sub>,F<sub>n</sub>)<sub>1</sub><sup>∞</sup>是适应的报酬序列,(γ<sub>n</sub>)是相应的snell 包,(A<sub>n</sub>)是(γ<sub>n... 设(X<sub>n</sub>,F<sub>n</sub>)<sub>1</sub><sup>∞</sup>是适应的报酬序列,(γ<sub>n</sub>)是相应的snell 包,(A<sub>n</sub>)是(γ<sub>n</sub>)的Doob-Meyer 分解中零初值的可料增过程。本文继J.Klass 的研究证明了σ<sub>1</sub>=inf{K≥1:X<sub>k</sub>≥γ<sub>k</sub>}是最小半最优的且是最大严格正则的广义规则,而K<sub>0</sub>=sup{n≥0:A<sub>n</sub>=0}【∞是最大正则的广义规则,从而得出了广义最优规则唯一性的另一表述。 展开更多
关键词 随机过程 最优停止规则 半最优
下载PDF
基于改进BP神经网络的无线电能传输系统接收线圈参数优化 被引量:9
9
作者 闻枫 荆凡胜 +2 位作者 李强 赵文翰 朱雪琼 《电工技术学报》 EI CSCD 北大核心 2021年第S02期412-422,共11页
为提升无线电能传输(WPT)系统的传输性能,该文研究了磁谐振式无线电能传输(MRWPT)系统的磁通与接收线圈内半径的变化规律,提出了最优接收半径的概念,通过分析平面方形、平面盘式和空间螺旋形三种类型发射线圈WPT系统,揭示了最优接收半... 为提升无线电能传输(WPT)系统的传输性能,该文研究了磁谐振式无线电能传输(MRWPT)系统的磁通与接收线圈内半径的变化规律,提出了最优接收半径的概念,通过分析平面方形、平面盘式和空间螺旋形三种类型发射线圈WPT系统,揭示了最优接收半径的固有存在性,并探究了最优接收半径随WPT系统参数的变化规律,从而确定影响最优接收半径的参数。在此基础上通过采用遗传算法改进的BP神经网絡对最优接收半径随影响参数的变化规律进行学习,实现了在不同线圈参数下最优接收半径的精确预测。最后通过有限元仿真和实验验证了WPT系统最优接收半径的存在和改进BP神经网络预测结果的准确性。 展开更多
关键词 无线电能传输 最优接收 遗传算法 BP神经网络 传输性能
下载PDF
具有保护区域的无线Ad-hoc网络传输性能研究 被引量:2
10
作者 唐菁敏 倪晨泉 +2 位作者 杨孟 陈昌海 赵坤 《电子科技大学学报》 EI CAS CSCD 北大核心 2014年第4期519-523,共5页
对现有抑制网络中干扰信号强度的方法进行了研究,针对抑制干扰的同时也限制了网络的传输容量的问题,提出在无线Ad-hoc网络中设置保护区域来抑制干扰,并推导了最优保护区域的半径。理论分析和仿真结果表明,设置保护区域能够极大程度降低... 对现有抑制网络中干扰信号强度的方法进行了研究,针对抑制干扰的同时也限制了网络的传输容量的问题,提出在无线Ad-hoc网络中设置保护区域来抑制干扰,并推导了最优保护区域的半径。理论分析和仿真结果表明,设置保护区域能够极大程度降低网络中的干扰信号强度,合理地设置保护区域大小能有效提高传输容量,并且保护区域半径存在一个最优值,能使得网络的传输容量达到最大值。 展开更多
关键词 无线自组织网 干扰抑制 最优保护 传输容量
下载PDF
MIMO MC-CDMA的简化CMOE递归自适应多用户检测
11
作者 赵发勇 酆广增 《应用科学学报》 CAS CSCD 北大核心 2008年第5期461-466,共6页
将约束最小输出能量(CMOE)准则应用于空时编码多输入多输出多载波码分多址(STBC MIMO MC-CDMA)系统,提出一种基于简化CMOE的联合信道估计与信号检测的递归自适应算法,解决了可变对角因子的自适应取值问题,所给出的最优步长半盲自适应信... 将约束最小输出能量(CMOE)准则应用于空时编码多输入多输出多载波码分多址(STBC MIMO MC-CDMA)系统,提出一种基于简化CMOE的联合信道估计与信号检测的递归自适应算法,解决了可变对角因子的自适应取值问题,所给出的最优步长半盲自适应信道估计可以提高信道估计的准确性和收敛速度.比较了不同环境下信道估计的误差和各种算法的误码率性能. 展开更多
关键词 空时编码 多输入多输出多载波码分多址 约束最小输出能量 最优步长盲自适应信道估计 多用户检测
下载PDF
PIECEWISE LINEAR NCP FUNCTION FOR QP FREE FEASIBLE METHOD 被引量:6
12
作者 Pu Dingguo Zhou Yan 《Applied Mathematics(A Journal of Chinese Universities)》 SCIE CSCD 2006年第3期289-301,共13页
In this paper, a QP-free feasible method with piecewise NCP functions is proposed for nonlinear inequality constrained optimization problems. The new NCP functions are piecewise linear-rational, regular pseudo-smooth... In this paper, a QP-free feasible method with piecewise NCP functions is proposed for nonlinear inequality constrained optimization problems. The new NCP functions are piecewise linear-rational, regular pseudo-smooth and have nice properties. This method is based on the solutions of linear systems of equation reformulation of KKT optimality conditions, by using the piecewise NCP functions. This method is implementable and globally convergent without assuming the strict complementarity condition, the isolatedness of accumulation points. Purr thermore, the gradients of active constraints are not requested to be linearly independent. The submatrix which may be obtained by quasi-Newton methods, is not requested to be uniformly positive definite. Preliminary numerical results indicate that this new QP-free method is quite promising. 展开更多
关键词 constrained optimization SEMISMOOTH nonlinear complementarity convergence.
下载PDF
Optimal selection of annulus radius ratio to enhance heat transfer with minimum entropy generation in developing laminar forced convection of water-Al2O3 nanofluid flow 被引量:23
13
作者 Siavashi Majid Jamali Mohammad 《Journal of Central South University》 SCIE EI CAS CSCD 2017年第8期1850-1865,共16页
Heat transfer and entropy generation of developing laminar forced convection flow of water-Al_2O_3 nanofluid in a concentric annulus with constant heat flux on the walls is investigated numerically. In order to determ... Heat transfer and entropy generation of developing laminar forced convection flow of water-Al_2O_3 nanofluid in a concentric annulus with constant heat flux on the walls is investigated numerically. In order to determine entropy generation of fully developed flow, two approaches are employed and it is shown that only one of these methods can provide appropriate results for flow inside annuli. The effects of concentration of nanoparticles, Reynolds number and thermal boundaries on heat transfer enhancement and entropy generation of developing laminar flow inside annuli with different radius ratios and same cross sectional areas are studied. The results show that radius ratio is a very important decision parameter of an annular heat exchanger such that in each Re, there is an optimum radius ratio to maximize Nu and minimize entropy generation. Moreover, the effect of nanoparticles concentration on heat transfer enhancement and minimizing entropy generation is stronger at higher Reynolds. 展开更多
关键词 nanofluid heat transfer enhancement forced convection entropy generation annulus radius ratio
下载PDF
Determination of processing power and optimum billet radius of modified backward extrusion by upper bound approach 被引量:1
14
作者 S.H.HOSSEINI K.ABRINIA 《Transactions of Nonferrous Metals Society of China》 SCIE EI CAS CSCD 2016年第8期2170-2178,共9页
A recently developed backward extrusion method entitled “modified backward extrusion” was presented using an upper bound analysis. For this purpose deformation area was divided into four distinct zones and a kinemat... A recently developed backward extrusion method entitled “modified backward extrusion” was presented using an upper bound analysis. For this purpose deformation area was divided into four distinct zones and a kinematically admissible velocity field for each of them was suggested. Total dissipated power was calculated for the deformation zones and the extrusion power wascomputed. The correlations of important geometrical parameters with extrusion force and dissipated powers were shown. Finding the initial billet size, a challenging area in the modified backward extrusion method, was discussed and the optimum billet radius was obtained, considering the minimum relative extrusion pressure. Finite element analyses were conducted and the results werecompared with the upper bound analysis. Finally, experiments were executed on commercially pure aluminium and a good agreement between upper bound and finite element analyses with experimental values was observed. 展开更多
关键词 modified backward extrusion upper bound method finite element analysis optimum billet radius
下载PDF
Optimality Conditions and Duality for Nondifferentiable Multiobjective Semi-Infinite Programming Problems with Generalized(C,α,ρ,d)-Convexity 被引量:6
15
作者 MISHRA Shashi Kant JAISWAL Monika HOAI AN Le Thi 《Journal of Systems Science & Complexity》 SCIE EI CSCD 2015年第1期47-59,共13页
This paper obtains sufficient optimality conditions for a nonlinear nondifferentiable multiobjective semi-infinite programming problem involving generalized(C,α,ρ,d)-convex functions.The authors formulate Mond-Weir-... This paper obtains sufficient optimality conditions for a nonlinear nondifferentiable multiobjective semi-infinite programming problem involving generalized(C,α,ρ,d)-convex functions.The authors formulate Mond-Weir-type dual model for the nonlinear nondifferentiable multiobjective semiinfinite programming problem and establish weak,strong and strict converse duality theorems relating the primal and the dual problems. 展开更多
关键词 DUALITY generalized convexity optimality conditions semi-infinite programming.
原文传递
SEMI-DEFINITE RELAXATION ALGORITHM FOR SINGLE MACHINE SCHEDULING WITH CONTROLLABLE PROCESSING TIMES
16
作者 CHENFENG ZHANGLIANSHENG 《Chinese Annals of Mathematics,Series B》 SCIE CSCD 2005年第1期153-158,共6页
The authors present a semi-definite relaxation algorithm for the scheduling problem with controllable times on a single machine. Their approach shows how to relate this problem with the maximum vertex-cover problem wi... The authors present a semi-definite relaxation algorithm for the scheduling problem with controllable times on a single machine. Their approach shows how to relate this problem with the maximum vertex-cover problem with kernel constraints (MKVC).The established relationship enables to transfer the approximate solutions of MKVCinto the approximate solutions for the scheduling problem. Then, they show how to obtain an integer approximate solution for MKVC based on the semi-definite relaxation and randomized rounding technique. 展开更多
关键词 Scheduling with controllable times Semi-definite programming Approximation algorithm
原文传递
Nonsmooth Semi-Infinite Minmax Programming Involving Generalized(Φ, ρ)-Invexity
17
作者 UPADHYAY B B MISHRA S K 《Journal of Systems Science & Complexity》 SCIE EI CSCD 2015年第4期857-875,共19页
This paper introduces some new generalizations of the concept of (~, p)-invexity for non- differentiable locally Lipschitz functions using the tools of Clarke subdifferential. These functions are used to derive the ... This paper introduces some new generalizations of the concept of (~, p)-invexity for non- differentiable locally Lipschitz functions using the tools of Clarke subdifferential. These functions are used to derive the necessary and sufficient optimality conditions for a class of nonsmooth semi-infinite minmax programming problems, where set of restrictions are indexed in a compact set. Utilizing the sufficient optimality conditions, the authors formulate three types of dual models and establish weak and strong duality results. The results of the paper extend and unify naturally some earlier results from the literature. 展开更多
关键词 Duality generalized invexity locally Lipschitz functions minmax programming semi-infinite programming.
原文传递
上一页 1 下一页 到第
使用帮助 返回顶部