单有向电磁矢量传感器的参数估计方法

传统的单电磁矢量传感器(UEMVS)由3个电偶极子和3个磁环构成且方向图是全向的。但是当多个单电磁矢量传感器依附在共形载体上构成共形电磁矢量传感器阵列时,为了降低共形电磁矢量传感器阵列的副瓣,通常每个传感器的方向图是有向的。基于有向方向图的单电磁矢量传感器也称为单有向电磁矢量传感器(UDEMVS)。该文针对UDEMVS的参数估计问题,提出两种参数估计方法,分别是基于免搜索的旋转不变信号参数估计和矢量叉积(ESPRIT-VCP)方法以及基于网格搜索的多重信号分类和最小瑞利商(MUSIC-MRQ)方法。ESPRIT-VCP方法是根据旋转不变性和矢量叉积,获得4维参数的闭式解,MUSIC-MRQ方法根据信号和噪声子空间正交性与最小瑞利商,利用网格搜索得到2维角度估计值,进而结合信号回波模型得到2维极化的估计值。所提两种方法只利用了UDEMVS的6通道数据就能有效得到目标的参数估计结果,有较低的计算复杂度。仿真结果从角度和极化的估计性能出发验证了所提方法的有效性。

Dynamic analysis of pavement on long span steel bridge decks

In order to analyze the dynamic response of pavement on long-span steel bridge decks under random dynamic loads, the irregularities of the pavement surface is simulated with the power spectrum density function, and the random load is calculated according to a vehicle vibration equation of vehicle model. The mechanical responses of three different cases are compared by using a transient dynamic analysis method, i. e., under random dynamic load, constant moving load and dead load respectively. The results indicate that the mid-span of two adjacent transversal diaphragms is the worst load position. The maximum vertical displacement and the maximum transversal tensile stress of the pavement are 1.33 times and 1.39 times as much as those when only considering the impact coefficients. This study not only provides a theoretical basis for the mixture design and structural design of pavement, but also puts forward higher demand on the construction and maintenance for steel deck pavement.

Finite element numerical simulation of 2.5D direct current method based on mesh refinement and recoarsement

To deal with the problem of low computational precision at the nodes near the source and satisfy the requirements for computational efficiency in inversion imaging and finite-element numerical simulations of the direct current method, we propose a new mesh refinement and recoarsement method for a two-dimensional point source. We introduce the mesh refinement and mesh recoarsement into the traditional structured mesh subdivision. By refining the horizontal grids, the singularity owing to the point source is minimized and the topography is simulated. By recoarsening the horizontal grids, the number of grid cells is reduced significantly and computational efficiency is improved. Model tests show that the proposed method solves the singularity problem and reduces the number of grid cells by 80% compared to the uniform grid refinement.

Two-dimensional frequency-domain acoustic fullwaveform inversion with rugged topography

We studied finite-element-method-based two-dimensional frequency-domain acoustic FWI under rugged topography conditions. The exponential attenuation boundary condition suitable for rugged topography is proposed to solve the cutoff botmdary problem as well as to consider the requirement of using the same subdivision grid in joint multifrequency inversion. The proposed method introduces the attenuation factor, and by adjusting it, acoustic waves are sufficiently attenuated in the attenuation layer to minimize the cutoff boundary effect. Based on the law of exponential attenuation, expressions for computing the attenuation factor and the thickness of attenuation layers are derived for different frequencies. In multifrequency-domain FWI, the conjugate gradient method is used to solve equations in the Gauss-Newton algorithm and thus minimize the computation cost in calculating the Hessian matrix. In addition, the effect of initial model selection and frequency combination on FWI is analyzed. Examples using numerical simulations and FWI calculations are used to verify the efficiency of the proposed method.

Nonlinear dynamical response of high-voltage transmission lines based on cable dropping

In order to study the dynamic response of high-voltage transmission lines under mechanical failure, a finite element model of a domestic 500-kV high-voltage transmission line system is established. The initial equilibrium condition of the coupling system model is verified by nonlinear static analysis. The transient dynamic analysis method is proposed to analyze the variation law of dynamic response under cable or insulator rupture, and the dynamic response of structural elements next to the broken span is calculated. The results show that upper crossarm cable rupture has no effect on cable tension at adjacent suspension points, but it has a significant influence on tension in the insulator and the tower component of the upper crossarm next to the broken span. The peak tension in the conductor of the upper crossarm at the suspension point exceeds the design value under insulator rupture. Insulator rupture has no effect on the tower component of the upper crossarm, but it has a significant influence on insulator tension of the upper crossarm. Insulator rupture should be taken into account in the design of overhead transmission lines. The research results can provide a theoretical basis for the design of transmission lines.

What determines the number of dominant species in forests?

In this work, the difference in number of dominant species in a community on global scale and successional trajectories was analyzed based on the published data. We explained the reasons of these differ-ences using a resource availability hypothesis, proposed in this work, that the distribution of available resource determined the pattern of commu-nity dominance. The results showed that on global scale the number of dominant species of community varied across latitudinal forest zone, namely from single-species dominance in boreal and temperate forest to multi-species codominance, even no dominant species in tropical forest. This was consistent with the pattern of resource distribution on global scale. Similarly, in successional trajectories, the number of dominant species gradually radiated from single-species dominance to multi-species codominance, even no dominant species in tropical forest. The changing available resources in trajectories were responsible for this difference. By contrary, a community was often dominated by single species in temperate or boreal forest. This was determined by the low available resource, especially low available water and temperature. In boreal forest, low temperature greatly reduced availability of water and nutrient, which were responsible for the single-species dominance. In addition, the conclusion that high available resources sustained low dominance of community might be deduced, based on the fact that the dominance of community declined with the increasing of species diversity. To sum up, the richer the available resources were, the lower the dominance of community was, and vice versa. The hypothesis that the resource availability controlled the dominance of community could well elucidate the difference of community dominance on global and community scale.

Contrast between 2D inversion and 3D inversion based on 2D high-density resistivity data

The 2D data processing adopted by the high-density resistivity method regards the geological structures as two degrees, which makes the results of the 2D data inversion only an approximate interpretation;the accuracy and effect can not meet the precise requirement of the inversion. Two typical models of the geological bodies were designed, and forward calculation was carried out using finite element method. The forward-modeled profiles were obtained. 1% Gaussian random error was added in the forward models and then 2D and 3D inversions using a high-density resistivity method were undertaken to realistically simulate field data and analyze the sensitivity of the 2D and 3D inversion algorithms to noise. Contrast between the 2D and 3D inversion results of least squares inversion shows that two inversion results of high-density resistivity method all can basically reflect the spatial position of an anomalous body. However, the 3D inversion can more effectively eliminate the influence of interference from Gaussian random error and better reflect the distribution of resistivity in the anomalous bodies. Overall, the 3D inversion was better than 2D inversion in terms of embodying anomalous body positions, morphology and resistivity properties.

论物权法的调整范围

物权法的调整范围是物权法的基本理论问题。由于深受古老的“拜所有权教”的影响，传统物权法的调整范围主要限于单一所有。及至物权二元结构论的提出，才将物权法的调整范围确定为单一所有与单一占有并重。但是与单有相对的共有在其理论中并没有实质性的变化。物权法的调整范围应是单有与共有的并列的双重结构。

The Multiplier Algebra of a Ternary Algebra

In this article, we have given the definition of the relative double multiplier (quasi-multiplier) on a ternary algebra,and studied the isomorphic problem of the multiplier algebra M(A,e) of a ternary algerbra A.

BIO-INSPIRED SELF-ADAPTIVE MANUFACTURING SYSTEM CONTROL ARCHITECTURE

Future manufacturing systems need to cope with frequent changes and disturbances, therefore their control architectures require constant adaptability, agility, stability, self-organization, intelligence, and robustness. Bio-inspired manufacturing system can well satisfy these requirements. For this purpose, by referencing the biological organization structure and the mechanism, a bio-inspired manufacturing cell is presented from a novel view, and then a bio-inspired self-adaptive manufacturing model is established based on the ultra-short feedback mechanism of the neuro-endocrine system. A hio-inspired self-adaptive manufacturing system coordinated model is also established based on the neuro-endocrine-immunity system （NEIS）. Finally, an example based on pheromone communication mechanism indicates that the robustness of the whole manufacturing system is improved by bio-inspired technologies.

NEW LIMITED MEMORY SYMMETRIC RANK ONE ALGORITHM FOR LARGE-SCALE UNCONSTRAINED OPTIMIZATION

A new limited memory symmetric rank one algorithm is proposed. It combines a modified self-scaled symmetric rank one （SSR1） update with the limited memory and nonmonotone line search technique. In this algorithm, the descent search direction is generated by inverse limited memory SSR1 update, thus simplifying the computation. Numerical comparison of the algorithm and the famous limited memory BFGS algorithm is given. Comparison results indicate that the new algorithm can process a kind of large-scale unconstrained optimization problems.

Finite element failure analysis of continuous prestressed concrete box girders

In order to analyze the load carrying capacity of prestressed concrete box girders, failure behaviors of in-situ deteriorated continuous prestressed concrete box girders under loading are experimentally observed and a finite failure analysis method for predicting behaviors of box girders is developed. A degenerated solid shell element is used to simulate box girders and material nonlinearity is considered. Since pre-stressed concrete box girders usually have a large number of curve prestressed tendons, a type of combined element is presented to simulate the prestressed tendons of box girders, and then the number of elements can be significantly reduced. The analytical results are compared with full-scale failure test results. The comparison shows that the presented method can be effectively applied to the failure analysis of in-situ continuous prestressed concrete box girders, and it also shows that the studied old bridge still has enough load carrying capacity.

A Compact Ka-Band PHEMT MMIC Voltage Controlled Oscillator

A compact Ka-band monolithic microwave integrated circuit(MMIC) voltage controlled oscillator (VCO) with wide tuning range and high output power,which is based on GaAs PHEMT process,is presented.A method is introduced to reduce the chip size and to increase the bandwidth of operation.The procedure to design a MMIC VCO is also described here.The measured oscillating frequency of the MMIC VCO is 36±1.2GHz and the output power is 10±1dBm.The fabricated MMIC chip size is 1.3mm×1.0mm.

Effects of cell wall property on compressive performance of aluminum foams

The effects of cell wall property on the compressive performance of high porosity, closed-cell aluminum foams prepared by gas injection method were investigated. The research was conducted both experimentally and numerically. Foam specimens prepared from conditioned melt were tested under uniaxial compressive loading condition. The cell wall microstructure and fracture were observed through optical microscope（OM） and scanning electron microscope（SEM）, which indicates that the cell wall property is impaired by the defects in cell walls and oxide films on the cell wall surface. Subsequently, finite element（FE） models based on three-dimensional thin shell Kelvin tetrakaidecahedron were developed based on the mechanical properties of the raw material and solid material that are determined by using experimental measurements. The simulation results show that the plateau stress of the nominal stress-strain curve exhibits a linear relationship with the yield strength of the cell wall material. The simulation plateau stress is higher than the experimental data, partly owing to the substitution of solid material for cell wall material in the process of the establishment of FE models.

Temperature Effect on the Life History of Three Types of Brachionus calyciflorus Females

The effect of temperature on the life history characteristics of amictic females (AF), unfertilized mictic females (UMF) and fertilized mictic females (FMF) in Brachionus calyciflorus was studied with replicated individual cultures at 20℃,25℃ and 30℃, and with algae Scenedesmus obliquus for their food. There were highly significant effects of both temperature and female type, independently and interactively, on the duration of juvenile and post-reproduction periods, and the number of eggs produced by the rotifer per life cycle. Among all the temperature-female type combinations, all the juvenile periods of FMF, and the post-reproduction periods of UMF and FMF at 20℃, were the longest, and the number of eggs produced by an UMF at 30℃ was the highest. There were highly significant effects of both temperature and female type on the duration of the reproduction period, but no clear correlation was observed between temperature and female type. The reproduction period of AF was longer than that of UMF and FMF. Only temperature influenced significantly the mean life-span of the three types of females. The duration of juvenile, reproduction and post-reproduction periods as well as the life-span of the three types of females were all reduced very significantly with rise of temperature, but the rates of reduction varied with female type. Among the three types of females, the number of eggs produced per life cycle by an UMF was the highest, and that of a FMF was the lowest. A significant relationship between the number of eggs produced per life cycle and temperature was observed only in the UMF.

Isolation, Identification and Phosphate Solubilizing Capacity of Organophosphorus Solubilizing Bacteria in Rhizosphere Soil of Camellia oleifera

In order to obtain high-efficiency organophosphorus solubilizing bacteria, 21 strains of organophosphate solubilizing bacteria were isolated from the rhizosphere soil of Camellia oleifera plants, and the transparent circle method was used for rescreening. Only 4 strains of bacteria could form transparent circle on organophosphorus medium. The D/d value of 4 strains of bacteria was between 1.62 and 2.71, among which the D/d value of strain Y6 was the highest(2.71). The available phosphorus content of the fermentation supernatant was 8.50~14.79 mg/L, which was 7.88~14.17 mg/L higher than that of CK. The strain Y6 had the highest soluble phosphorus content of 14.79 mg/L in the fermentation supernatant, which was 14.17 mg/L higher than that of CK. According to the colony morphology, physiological and biochemical characteristics and 16S rDNA sequence analysis of strain Y6, it is preliminarily determined that strain Y6 is Pseudomonas. Strain Y6 is beneficial to improve the supply of phosphorus in rhizosphere soil of Camellia oleifera and promote the growth of Camellia oleifera. It has great potential in the development of bio-organic fertilizer.

Relative Basicity of Trioctylamine to Carboxylic Acid in Selected Organic Diluents

The relative basicity of trioctylamine （TOA）, pKa,BS, in protic polar diluent （1-octanol）, non-protic polar diluent [methyl iso-butyl ketone （MIBK）] and inert diluent （CCl4） were determined for 11 mono-carboxylic acids, and the dependence of PKa,BS on the nature of solute and diluent type was discussed. The results show that pKa,BS determined by half neutralization with the solute carboxylic acid is in the order of 1-octanol〉MIBK〉CCl4 for a fixed TOA concentration, and it increases with increasing acidity and hydrophobicity of the carboxylic acid. Compared with two parameters of the solute extracted （acidity and hydrophobicity）, pKa,BS is more sensitive to hydrophobicity of the acid. A mathematic equation representing relationship between the apparent extraction equilibrium （K11） and the system properties （PKa,BS and pKa） was proposed： 1g K11 = 2pKa,BS=pKa. It is proved that the extraction equilibrium of mono-carboxylic acids can be predicted by the above equation with reasonable accuracy.

Comparison on construction of strut-and-tie models for reinforced concrete deep beams

With consideration of the differences between concrete and steel,three solutions using genetic evolutionary structural optimization algorithm were presented to automatically develop optimal strut-and-tie model for deep beams.In the finite element analysis of the first method,the concrete and steel rebar are modeled by a plane element and a bar element,respectively.In the second method,the concrete and steel are assigned to two different plane elements,whereas in the third method only one kind of plane element is used with no consideration of the differences of the two materials.A simply supported beam under two point loads was presented as an example to verify the validity of the three proposed methods.The results indicates that all the three methods can generate optimal strut-and-tie models and the third algorithm has powerful capability in searching more optimal results with less computational effort.The effectiveness of the proposed algorithm III has also been demonstrated by other two examples.

Phosphate-Solubilizing and -Mineralizing Abilities of Bacteria Isolated from Soils

Microorganisms capable of solubilizing and mineralizing phosphorus （P） pools in soils are considered vital in promoting P bioavallability. The study was conducted to screen and isolate inorganic P-solubilizing bacteria （IPSB） and organic P-mineralizing bacteria （OPMB） in soils taken from subtropical flooded and temperate non-flooded soils, and to compare inorganic P-solubilizing and organic P-solubilizing abilities between IPSB and OPMB. Ten OPMB strains were isolated and identified as Bacillus cereus and Bacillus megaterium, and five IPSB strains as B. megaterium, Burkholderia caryophyUi, Pseudomonas cichorii, and Pseudomonas syringae. P-solubilizing and -mineralizing abilities of the strains were measured using the methods taking cellular P into account. The IPSB strains exhibited inorganic P-solubilizing abilities ranging between 25.4-41.7 μg P mL^-1 and organic P-mineralizing abilities between 8.2-17.8μg P mL^-1. Each of the OPMB strains also exhibited both solubilizing and mineralizing abilities varying from 4.4 to 26.5 μg P mL^-1 and from 13.8 to 62.8 μg P mL^-1, respectively. For both IPSB and OPMB strains, most of the P mineralized from the organic P source was incorporated into the bacterial cells as cellular P. A significantly negative linear correlation （P 〈 0.05） was found between culture pH and P solubilized from inorganic P by OPMB strains. The results suggested that P solubilization and mineralization could coexist in the same bacterial strain.

Residual stress and welding distortion of Al/steel butt joint by arc-assisted laser welding-brazing

The thermo-elastic.plastic finite element method(FEM)is used to simulate the thermo-mechanical behavior of Al/steel tungsten inert gas(TIG)arc-assisted laser welding-brazing(A-LWB)butt joint.The influence of material nonlinearity,geometrical nonlinearity and work hardening on the welding process is studied,and the differences in the welding temperature field,residual stress and welding distortion by A-LWB and by single laser welding-brazing(SLWB)are analyzed.The results show that the thermal cycle,residual stress distribution and welding distortion by the numerical simulation are in good agreement with the measured data by experiments,which verifies the effectiveness of FEM.Compared with the SLWB,A-LWB can make the high-temperature distribution zone of weld in width direction wider,decrease the transverse tensile stress in the weld and reduce the distribution range of longitudinal tensile stress.And the welding deformation also decreases to some extent.