Dynamic analysis and optimization of car's body-in-white based on superelement approach

An approach based on the superelement theory is proposed, and it is applied to model the car's body-in-white as well as to dynamic simulation and optimization. This approach can improve the calculation speed and do the dynamic optimization among substructures respectively in the car's body design. To meet the car's design of harshness, a dynamic optimal design model, based on the mean square of vertical displacement response at two points of the car floor, is proposed. Satisfactory results are achieved.

Prediction of compressive strength of cement mortars with fly ash and activated coal gangue

The pozzolanic activity of coal gangue, which is calcining at 500 to 1 000 ℃, differs distinctly. The simplex-centroid design with upper and lower bounds of component proportion is adopted to study the compressive strength of mortars made with ternary blends of cement, activated coal gangue and fly ash. Based on the results of a minimum of seven design points, three special cubic polynomial models are used to establish the strength predicating equations at different ages for mortars. Five experimental checkpoints were also designed to verify the precision of the equations. The most frequent errors of the predicted values are within 3%. A simple and practical way is provided for determining the optimal proportion of two admixtures when they are used in concrete.

Investigation of cost-effectiveness of highway asphalt pavement maintenance treatments based on rutting development analysis

To investigate the cost-effectiveness of different maintenance treatments of highways in Jiangsu Province, the historical pavement maintenance records, traffic load information and pavement performance data in the pavement management system （PMS） are recorded and analyzed. Compared with the growth model, the linear model, the logarithm model and the exponential model, the cubic model has higher regression accuracy R2 and it can capture the sigmoid shape of the deterioration curve. So it is selected to simulate the pavement rotting development. The benefit over cost ratio is calculated to quantify the treatment cost- effectiveness. The analysis results show that thin hot mix asphalt （HMA） overlays and micro surfacing are more cost- effective than the. other two treatments on light and moderate traffic roads. Hot in-place recycling and thick HMA overlays have much longer service lives and greater cost-effectiveness under heavy or extra heavy traffic.

VALIDATION AND ANALYSES OF THE SIMPLE METHOD FOR DETERMINING rm OF APHIDS AND MITES

This paper deals with the validation and theoretical analyses of a simple method for calculating the intrinsic rate of increase, rm, of aphids and mites. This method does not require a detailed fecundity table data. The value of rm can be estimated by the simple equation: rm=0.74ln (Md)/d, where d is the time from birth to first reproduction; Md is the number of female offspring produced per original female in 2d. This method was developed by Wyatt and White. We reached the following conclusions from our study: When the parameter, Md is less than 1, this equation is not appropriate for estimating rm of populations; When the parameter, Md is larger than 1 and about 70% or more of the reproductive contribution to the rm is achieved in 2d, the equation is appropriate for calculatng the rm of aphids and mites.As Md decreases, the required reproductive contribution to the rm in 2d corresponding to the constant 0.74 will increase. However, whether 70% or more of reproductive contribution to rm is achieved in 2d still is a problem for whole taxa of aphids and mites. Therefore, further siudy on reproductive distribution will be required for practical application of this method.

测量设备无关量子密钥分配的综合参数估计

参数估计(单光子计数率与误码率)是影响诱骗态MDI-QKD(measurement device-independent quantum key distdbution)成码率的重要因素.利用综合估计的方法,研究采用自发参量下转换(spontaneous parametric down conversion,SPDC)源的MDI-QKD参数估计问题.区别于已有的独立估计方法,从平均计数率和误码率方程组中得到参数解析式,然后充分考虑参数之间的关联性,将其作为一个整体函数进行分析.通过在闭区间内求函数最小值,给出了更紧的安全码率估计.该方法为进一步提升此类MDI-QKD协议的性能提供了思路.

Co-Design of Monolithically Integrated Photo-Detector and Optical-Receiver

A behavioral model of the photodiode is presented.The model describes the relationship between photocurrent and incident optical power,and it also illustrates the impact of the reverse bias to the variation of the junction capacitance.According to this model,the photodiode and a CMOS receiver circuit are simulated and designed simultaneously under a universal circuit simulation environment.

The group search-based parallel algorithm for the serial Monte Carlo inversion method

With the development of parallel computing technology,non-linear inversion calculation efficiency has been improving.However,for single-point search-based non-linear inversion methods,the implementation of parallel algorithms is a difficult issue.We introduce the idea of group search to the single-point search-based non-linear inversion algorithm, taking the quantum Monte Carlo method as an example for two-dimensional seismic wave velocity inversion and practical impedance inversion and test the calculation efficiency of using different node numbers.The results show the parallel algorithm in theoretical and practical data inversion is feasible and effective.The parallel algorithm has good versatility. The algorithm efficiency increases with increasing node numbers but the algorithm efficiency rate of increase gradually decreases as the node numbers increase.

A method of automatic plane detection without random search

Plane detection is a prerequisite for many computer vision tasks. This paper proposes a new method which can automatically detect planes from two projective images. Firstly, we modify Scott’s feature point matching method by post-processing its result with the concept of similarity, and then get the lines matching according to feature points matching based on the approximate invariance of the features’ distribution between two images. Finally, we group all feature points into subsets in terms of their geometric relations with feature lines as initial sets to estimate homography rather than by a random search strategy (like RANSAC) as in most existing methods. The proposed method is especially suitable to detecting planes in man-made scenes. This method is validated on real images.

CONTROL STRUCTURE AND IMPLEMENTATION OF CELL CONTROL SYSTEM

Cell control system(CCS) plays an important role in the hierarchical control structure of computer integrated manufacturing system(CIMS). It links up workshop controller and CAD/CAPP/CAM down to production facilities, and directly influences flexibility and efficiency of production. The hierarchical control structure and the key technical problems of the CCS are mainly described. The CCS controls the job schedule, the resource allocation and the operation of facilities in the manufacturing procedure according to the production plan and target coming from the workshop controller. The key technologies are discussed in this paper as follows: the application of client/server system structure in the production control and management; production planning and scheduling; the handling of exceptional incidents in production and the DNC interface control as well.

Optimization of PCR Reaction System for Random Single-strand DNA Pool in SELEX Technology

[Objective] This study aimed to optimize the PCR amplification conditions for random ssDNA pool in SELEX technology. [Method] L16（45） orthogonal experimental design was adopted for optimization of five important factors affecting PCR reaction system for random single-stranded DNA pool including Mg2＋ concentration, dNTP concentration, amount of Taq DNA polymerase, primer concentration and amount of random single-stranded DNA pool at four levels. Meanwhile, the annealing temperature and number of PCR reaction cycles were optimized to establish the optimal reaction system and PCR procedure. [Result] The optimal combination of PCR reaction system for random ssDNA pool was obtained, with a total system volume of 20 μl containing 2.0 μl of 10 × Buffer, 0.5 ng of random ssDNA pool, 2.5 mmol/L Mg2＋, 0.25 mmol/L dNTP Mixture, 0.6 μmol/L upstream and downstream primers and 1.5 U of Taq DNA polymerase; the optimal annealing temperature was 68 ℃ and the optimal number of cycles was 12. Under the above conditions, clear and stable bands with high specificity for random ssDNA pool were amplified. [Conclusion] This study laid the foundation for selection of parameters with higher specificity in SELEX technology.

Hardware Optimization Technique of Full-Customized HW/SW Co-Design

The hardware optimization technique of mono similarity system generation is presented based on hardware/software(HW/SW) co design.First,the coarse structure of sub graphs' matching based on full customized HW/SW co design is put forward.Then,a universal sub graphs' combination method is discussed.Next,a more advanced vertexes' compression algorithm based on sub graphs' combination method is discussed with great emphasis.Experiments are done successfully with perfect results verifying all the formulas and the methods above.

Flexoelectric-Induced Voltage Shift in Hybrid Aligned Nematic Liquid Crystal Cell

Flexoelectric-induced voltage shift in a weak anchoring hybrid aligned nematic fiquid crystai cell is investigated theoretically. Based on the elastic theory of liquid crystal and the variation method, the equations for the bulk and the boundary of the cell are derived. By computer simulation, the dependence of the shift voltage on the sum of the ttexoelectric coefficients and the anchoring energy strength is obtained. As a result, a novel method to determine the sum of the flexoelectric coefficients by measuring the shift voltage is put forward.

Effect of single dead end entry inclination on DPM plume dispersion

Diesel particulate matter(DPM) is a by-product from operating diesel engines. Since diesel powers are one of the major sources of energy for mobile underground mining equipment, the adverse health effects of DPM are of a great concern. This paper used computational fluid dynamics(CFD) method to study the effect of entry inclination on DPM plume distribution in a dead end entry. An upward mining face and a downward mining face were built with a truck and a loader in loading operation close to the face area. A species transport model with incorporated buoyancy effect was used to examine the DPM dispersion pattern for the above steady-state scenarios. High DPM and temperature regions were identified for the two different faces. The model was used to assess the role of auxiliary ventilation in reducing DPM exposures of underground miners working in those entries. In this study, it is suggested to provide local ventilation at least three times of the diesel exhaust rate to be able to lower the average DPM level for the mining upward face. The requirement for local ventilation is much less for the mining downward face. This can provide guidelines for good working practices and selection of diesel emission reduction technologies underground.

Design of area and power efficient Radix-4 DIT FFT butterfly unit using floating point fused arithmetic

In this work, power efficient butterfly unit based FFT architecture is presented. The butterfly unit is designed using floating-point fused arithmetic units. The fused arithmetic units include two-term dot product unit and add-subtract unit. In these arithmetic units, operations are performed over complex data values. A modified fused floating-point two-term dot product and an enhanced model for the Radix-4 FFT butterfly unit are proposed. The modified fused two-term dot product is designed using Radix-16 booth multiplier. Radix-16 booth multiplier will reduce the switching activities compared to Radix-8 booth multiplier in existing system and also will reduce the area required. The proposed architecture is implemented efficiently for Radix-4 decimation in time(DIT) FFT butterfly with the two floating-point fused arithmetic units. The proposed enhanced architecture is synthesized, implemented, placed and routed on a FPGA device using Xilinx ISE tool. It is observed that the Radix-4 DIT fused floating-point FFT butterfly requires 50.17% less space and 12.16% reduced power compared to the existing methods and the proposed enhanced model requires 49.82% less space on the FPGA device compared to the proposed design. Also, reduced power consumption is addressed by utilizing the reusability technique, which results in 11.42% of power reduction of the enhanced model compared to the proposed design.

Coal pillar mechanics of violent failure in U.S. Mines

This paper seeks to enhance the understanding that the horizontal stresses build up and release during coal pillar loading and unloading(post-failure) drawing upon three decades of observations, geomechanical monitoring and numerical modeling in bump-prone U.S. mines. The focus is on induced horizontal stress in mine pillars and surrounding strata as highly stressed pillars punch into the roof and floor, causing shear failure and buckling of strata; under stiff stratigraphic units of some western US mines, these events could be accompanied by violent failure of pillar cores. Pillar punching eventually results in tensile stresses at the base of the pillar, facilitating transition into the post-failure regime; this transition will be nonviolent if certain conditions are met, notably the presence of interbedded mudstones with low shear strength properties and proper mine designs for controlling seismicity and dynamic loads. The study clearly shows high confining stress build-up in coal pillars resulting in up to twice higher peak vertical stress and high strain energy accumulations in some western US mines in comparison with peak stresses predicted using common empirical pillar design methods. It is the unstable release of this strain energy that can cause significant damage resulting from pillar dilation and ground movements. These forces are much greater than the capacity of most common internal support systems, resulting in horizontal stressinduced roof falls locally, in mines under unremarkable far-field horizontal stress. Attention should be placed on pillar designs as increasing support density may prove to be ineffective. This mechanism is analyzed using field measurements and generic finite-difference stress analyses. The study confirms the higher load carrying capacity of confinement-controlled coal seams in comparison with structurally controlled coal seams. Such significant differences in confining stresses are not taken into account when estimating peak pillar strength using most common empirical techniques such as those proposed by Bieniawski and Salamon. While using lower pillar strength estimates may be considered conservative,it underestimates the actual capacity of pillars in accumulating much higher stress and strain energies,misleading the designer and inadvertently diminishing mine safety. The role of induced horizontal stress in mine pillars and surrounding strata is emphasized in coal pillar mechanics of violent failure. The triggering mechanism for the violent events is sudden loss of pillar confinement due to dynamic loading resulting from failure of overlying stiff and strong strata. Evidence of such mechanism is noted in the field by observed red-dust at the coal-rock interfaces at the location of coal bumps and irregular, periodic caving in room-and-pillar mines quantified through direct pressure measurements in the gob.

Statistical damage model for quasi-brittle materials under uniaxial tension

Based on the parallel bar system, combining with the synergetic method, the catastrophe theory and the acoustic emission test, a new motivated statistical damage model for quasi-brittle solid was developed. Taking concrete for instances, the rationality and the flexibility of this model and its parameters-determining method were identified by the comparative analyses between theoretical and experimental curves. The results show that the model can simulate the whole damage and fracture process in the fracture process zone of material when the materials arc exposed to quasi-static uniaxial tensile traction. The influence of the mesoscopic damage mechanism on the macroscopic mechanical properties of quasi-brittle materials is summarized into two aspects, rupture damage and yield damage. The whole damage course is divided into the statistical even damage phase and the local breach phase, corresponding to the two stages described by the catastrophe theory. The two characteristic states, the peak nominal stress state and the critical state are distinguished, and the critical state plays a key role during the whole damage evolution course.

Weighted approximation of functions with singularities by Bernstein operators

As an important type of polynomial approximation, approximation of functions by Bernstein operators is an important topic in approximation theory and computational theory. This paper gives global and pointwise estimates for weighted approximation of functions with singularities by Bernstein operators. The main results are the Jackson＇s estimates of functions f∈ （Wwλ）2 andre Cw, which extends the result of （Della Vecchia et al., 2004）.

Impact of Continuous Chinese Fir Monoculture on Soil

Soil properties were investigated in sites where three succeeding generationsof Chinese fir (Gunning-hamia lanceolata, (Lambert) Hooker) in Nanping, Fujian, China, werecultivated in order to show the impact of a repeated monoculture on site productivity. Compared withthe first generation (FG) stand the soil structure deteriorated in the second generation (SG) andthe third generation (TG) stands. For instance, the destruction rate of the peds increased by 55%-115% in the SG and the TG stands compared to the FG stand. Soil nutrient storage and nutrientavailability also decreased in the SG and the TG stands. For surface soils of 0-20 cm, the organicmatter content, total N and P, and available N and P decreased by 3%-20% relative to those in the FGstand. For many soil parameters, the differences between the FG stand and the SG and the TG standswere statistically significant (LSD test, P < 0.05). Furthermore, with each succeeding generation ofChinese fir, the total number of soil microbes declined, the soil enzyme activity weakened, and thesoil biological activity decreased. In order to maintain sustainable site productivity, newsilvicultural practices need to be developed for management of Chinese fir plantations.

Model-based design method of two-axis four-actuator fast steering mirror system

This work was focused on the model-based design method of two-axis four-actuator(TAFA) fast steering mirror system(FSM), in order to improve the design efficiency. The structure and operation principle commonality of normal TAFA FSM were investigated. Based on the structure and the commonality, the conditions of single-axis idea, high-frequency resonance and coupling were modeled gradually. Combining these models, a holonomic system model was established to reflect and predict the performance of TAFA FSM. A model-based design method was proposed based on the holonomic system model. The design flow and design concept of the method were described. In accordance with the method, a TAFA FSM was designed. Simulations and experiments of the FSM were done, and the results of them were compared. The compared results indicate that the holonomic system model can well reflect and predict the performance of TAFA FSM. The bandwidth of TAFA FSM is more than 250 Hz; adjust time is less than 15 ms;overshoot is less than 8%; position accuracy is better than 10 μrad; the FSM prototype can satisfy the requirements.

CFD aided investigation of single droplet coalescence

This article describes the development of a coalescence model using various CFD work packages,and is validated using as toluene water model system.Numerical studies were performed to describe droplet interactions in liquid–liquid test systems.Current models use adjustable parameters to describe these phenomena.The research in the past decades led to different correlations to model coalescence and breakage depending on the chemical system and the apparatus geometry.Especially the complexity of droplet coalescence requires a detailed investigation of local phenomena during the droplet interaction.Computational fluid dynamics(CFD) studies of single droplet interactions were performed and validated with experimental results to improve the understanding of the local hydrodynamics and film drainage during coalescence.The CFD simulations were performed for the interaction of two differently sized droplets at industrial relevant impact velocities.The experimental verification and validation of the numerical results were done with standardized high-speed imaging studies by using a special test cell with a pendant and a free rising droplet.An experimental based algorithm was implemented in the open source code OpenF OAM to account for the contact time and the dimple formation.The standard European Federation of Chemical Engineering(EFCE) test system toluene/water was used for the numerical studies and the experimental investigations as well.The results of the CFD simulations are in good accordance with the observed coalescence behavior in the experimental studies.In addition,a detailed description of local phenomena,like film rupture,velocity gradients,pressures and micro-droplet entrainment could be obtained.