To enhance the reliability and to extend service life of packing rings, tribological and sealing perfor- mances are investigated based on the experimental results. Friction force, leakage rate and power consumption of...To enhance the reliability and to extend service life of packing rings, tribological and sealing perfor- mances are investigated based on the experimental results. Friction force, leakage rate and power consumption of three materials of pressure packing seals are measured in a refitted vertical gas compressor. The rings are made of common filled polytetrafiuroethylene （Filled PTFE）, PTFE reinforced with 30% mass fraction carbon fiber （30%CF^PTFE）, and carbon-carbon composites infiltrated with PTFE （C/C＋PTFE）, respectively. It is found that packing rings will periodically vibrate with the periodic vibration of pressure packing after the travel direction of motion abruptly turns to the reverse direction. Furthermore, the amplitude of vibration slows down with the increasing crank angle. Approximate value of friction force is available by multiple-point fast Fourier transformation （FFT） employed to process the experimental results by reducing the impact of vibration to a great extent. Of three materials of rings employed in experiments, Filled PTFE presents minimal leakage rate accom- panied with maximum power consumption. And 30%CF＋PTFE exhibits minimum friction power and moderate leakage rate. As for C/C＋PTFE, its high mechanical and thermal properties are favorable factors to enhance the ability of operating under high pressure and velocity and to improve the wear resistance. Unfortunately, this also leads to a large leakage rate. Comprehensive consideration should be taken into to evaluate the availability, reliability and service life for a type of packing ring under dry running conditions.展开更多
The Fuyang oil layer of the Songliao Basin is a tight and low-permeability sandstone pay zone formed in the fluvial-shallow water delta environment.In the formation are mainly lithologic reservoir and tight reservoir....The Fuyang oil layer of the Songliao Basin is a tight and low-permeability sandstone pay zone formed in the fluvial-shallow water delta environment.In the formation are mainly lithologic reservoir and tight reservoir.The lacustrine-mudstone of K2qn1 is a good source rock and also acts as a good regional cap rock.The Fuyang oil layer is a typical upper-source and lower-reservoir pattern distributed in a large area.Based on a large number of exploration and development data, a macroscopic enveloping surface is found developed in the Fuyang oil layer, which is below K2qn1.The effective reservoirs within the enveloping surface are commonly saturated with oil, and below the enveloping surface are mainly water layers.The distance from the enveloping surface to the bottom of the source rock is usually 100-350 m and at most 550 m.Through the research of the distribution patterns and the physical properties of the sandbodies above or beneath the source rock, it is concluded that: 1) the enveloping surface is the boundary of the overpressure hydrocarbon migration; 2) the spacial distribution of the pressure release beds controls the direction and the distance of the overpressure hydrocarbon migration; 3) tight oil reservoirs and lenticular oil reservoirs are mainly formed inside the envelope surface, whereas, conventional reservoirs are formed outside the envelope surface as a result of the buoyancy hydrocarbon migration.The discovery of the "overpressure hydrocarbon migration enveloping surface" and the concepts of overpressure hydrocarbon migration and buoyancy hydrocarbon migration not only challenge the old notion that "hydrocarbon migrates along the faults and is distributed along fault belts" in the Fuyang oil layer of the Songliao Basin, give a new explanation to the long-distance-oil-downwards migration (hundreds of meters) and expand the exploration potential of the Fuyang oil layer, and provide a rational guidance to the exploration of syncline plays, but also better categorize tight oil/gas and conventional reservoirs in all of the key elements related to hydrocarbon migration, accumulation, reservoir characteristics and oil and gas spatial distribution.展开更多
文摘To enhance the reliability and to extend service life of packing rings, tribological and sealing perfor- mances are investigated based on the experimental results. Friction force, leakage rate and power consumption of three materials of pressure packing seals are measured in a refitted vertical gas compressor. The rings are made of common filled polytetrafiuroethylene （Filled PTFE）, PTFE reinforced with 30% mass fraction carbon fiber （30%CF^PTFE）, and carbon-carbon composites infiltrated with PTFE （C/C＋PTFE）, respectively. It is found that packing rings will periodically vibrate with the periodic vibration of pressure packing after the travel direction of motion abruptly turns to the reverse direction. Furthermore, the amplitude of vibration slows down with the increasing crank angle. Approximate value of friction force is available by multiple-point fast Fourier transformation （FFT） employed to process the experimental results by reducing the impact of vibration to a great extent. Of three materials of rings employed in experiments, Filled PTFE presents minimal leakage rate accom- panied with maximum power consumption. And 30%CF＋PTFE exhibits minimum friction power and moderate leakage rate. As for C/C＋PTFE, its high mechanical and thermal properties are favorable factors to enhance the ability of operating under high pressure and velocity and to improve the wear resistance. Unfortunately, this also leads to a large leakage rate. Comprehensive consideration should be taken into to evaluate the availability, reliability and service life for a type of packing ring under dry running conditions.
基金supported by National Basic Research Program of China(Grant Nos.2006CB701404,2009CB219308)
文摘The Fuyang oil layer of the Songliao Basin is a tight and low-permeability sandstone pay zone formed in the fluvial-shallow water delta environment.In the formation are mainly lithologic reservoir and tight reservoir.The lacustrine-mudstone of K2qn1 is a good source rock and also acts as a good regional cap rock.The Fuyang oil layer is a typical upper-source and lower-reservoir pattern distributed in a large area.Based on a large number of exploration and development data, a macroscopic enveloping surface is found developed in the Fuyang oil layer, which is below K2qn1.The effective reservoirs within the enveloping surface are commonly saturated with oil, and below the enveloping surface are mainly water layers.The distance from the enveloping surface to the bottom of the source rock is usually 100-350 m and at most 550 m.Through the research of the distribution patterns and the physical properties of the sandbodies above or beneath the source rock, it is concluded that: 1) the enveloping surface is the boundary of the overpressure hydrocarbon migration; 2) the spacial distribution of the pressure release beds controls the direction and the distance of the overpressure hydrocarbon migration; 3) tight oil reservoirs and lenticular oil reservoirs are mainly formed inside the envelope surface, whereas, conventional reservoirs are formed outside the envelope surface as a result of the buoyancy hydrocarbon migration.The discovery of the "overpressure hydrocarbon migration enveloping surface" and the concepts of overpressure hydrocarbon migration and buoyancy hydrocarbon migration not only challenge the old notion that "hydrocarbon migrates along the faults and is distributed along fault belts" in the Fuyang oil layer of the Songliao Basin, give a new explanation to the long-distance-oil-downwards migration (hundreds of meters) and expand the exploration potential of the Fuyang oil layer, and provide a rational guidance to the exploration of syncline plays, but also better categorize tight oil/gas and conventional reservoirs in all of the key elements related to hydrocarbon migration, accumulation, reservoir characteristics and oil and gas spatial distribution.
