Introduction During the last two decades,organic light-emitting diodes (OLED) have attracted considerable interest owing to their promising applications by replacing cathode ray tubes (CRTs) or liquid crystal displays...Introduction During the last two decades,organic light-emitting diodes (OLED) have attracted considerable interest owing to their promising applications by replacing cathode ray tubes (CRTs) or liquid crystal displays (LCDs).展开更多
Temporal mode direct numerical simulation was done for the process of laminar-turbulent transition in an incompressible boundary layer on a flat plate. The analysis of the results showed that during the breakdown proc...Temporal mode direct numerical simulation was done for the process of laminar-turbulent transition in an incompressible boundary layer on a flat plate. The analysis of the results showed that during the breakdown process of laminar-turbulent transition, the modification of the mean flow profile by the disturbances led to a remarkable change in its stability characteristics, manifested in the significant enlargement of the linear unstable zone and the maximum amplification rate, and led to that many more disturbances were excited and enhanced rapidly, correspondingly the turbulent energy also increased rapidly, and the mean flow profiles evolved swiftly from laminar to turbulent. It was also found that if the oblique waves in the initial disturbances did not form symmetrical pairs, the subsequent span-wise mean velocities would, in general, be nonzero due to nonlinear interaction, which would have a great effect on the stability characteristics and also implied that the turbulence obtained by direct numerical simulation might not be fully a random process.展开更多
The roll contour pattern and variety of work and backup rolls in service and its effect on profile and flatness control performance in 1 700 mm hot strip mill at Wuhan Iron and Steel(Group) Corporation were tested and...The roll contour pattern and variety of work and backup rolls in service and its effect on profile and flatness control performance in 1 700 mm hot strip mill at Wuhan Iron and Steel(Group) Corporation were tested and analyzed by the developed finite element models of different typical roll contours configurations.A rather smooth local work roll contour near strip edges and an increase in rolled length can be obtained by application of long stroke work roll shifting system with conventional work roll contours that is incapable of the crown control.In comparison with the conventional backup and work roll contours configuration,the crown control range by the roll bending force enhances by 12.79% and the roll gap stiffness increases by 25.26% with the developed asymmetry self-compensating work rolls(ASR) and varying contact backup rolls(VCR).A better strip profile and flatness quality,an increase in coil numbers within the rolling campaign and a significant alleviated effect of severe work roll wear contours on performance of edge drop control are achieved by the application of ASR with crown control and wear control ability in downstream stand F5 and VCR in all stands of 1 700 mm hot strip mill.展开更多
The hardening curve for sheet metal can be determined from the load-displacement curve of tensile specimen with rectangular cross-section. Therefore,uniaxial compression test on cylinder specimen made from laminated s...The hardening curve for sheet metal can be determined from the load-displacement curve of tensile specimen with rectangular cross-section. Therefore,uniaxial compression test on cylinder specimen made from laminated sample is put forward. Considering the influence of anisotropy on hardening properties and the stress state in popular forming process,plane strain compression test on cubic specimen made from laminated sample was advanced. Results show that the deformation range of hardening curves obtained from the presented methods is wide,which meets the need for the application in sheet metal forming processes. In view of the characteristics of methods presented in the paper and the stress strain state of various forming processes,the adaptability of the two methods presented in this paper is given.展开更多
基金This work was supported by the National Science Support Program (2006BAE04B05-3)MOE Program for Changjiang Scholars and Innovative Research Team (grant No. 0629)+2 种基金National Science Foundation of China (grant No. 50505037)863 Hi-Teeh Program (grant No. 2006AA04Z322 )"Qing Lan" Talent Engineering Funds by Lanzhou Jiaotong University.
文摘Introduction During the last two decades,organic light-emitting diodes (OLED) have attracted considerable interest owing to their promising applications by replacing cathode ray tubes (CRTs) or liquid crystal displays (LCDs).
基金Supported by National Natural Science Foundation of China (No.90205021)Liu Hui Center of Applied Mathematics ,Nankai Universityand Tianjin University
文摘Temporal mode direct numerical simulation was done for the process of laminar-turbulent transition in an incompressible boundary layer on a flat plate. The analysis of the results showed that during the breakdown process of laminar-turbulent transition, the modification of the mean flow profile by the disturbances led to a remarkable change in its stability characteristics, manifested in the significant enlargement of the linear unstable zone and the maximum amplification rate, and led to that many more disturbances were excited and enhanced rapidly, correspondingly the turbulent energy also increased rapidly, and the mean flow profiles evolved swiftly from laminar to turbulent. It was also found that if the oblique waves in the initial disturbances did not form symmetrical pairs, the subsequent span-wise mean velocities would, in general, be nonzero due to nonlinear interaction, which would have a great effect on the stability characteristics and also implied that the turbulence obtained by direct numerical simulation might not be fully a random process.
基金Project(20040311890) supported by the Science and Technology Development Foundation of University of Science and Technology Beijing
文摘The roll contour pattern and variety of work and backup rolls in service and its effect on profile and flatness control performance in 1 700 mm hot strip mill at Wuhan Iron and Steel(Group) Corporation were tested and analyzed by the developed finite element models of different typical roll contours configurations.A rather smooth local work roll contour near strip edges and an increase in rolled length can be obtained by application of long stroke work roll shifting system with conventional work roll contours that is incapable of the crown control.In comparison with the conventional backup and work roll contours configuration,the crown control range by the roll bending force enhances by 12.79% and the roll gap stiffness increases by 25.26% with the developed asymmetry self-compensating work rolls(ASR) and varying contact backup rolls(VCR).A better strip profile and flatness quality,an increase in coil numbers within the rolling campaign and a significant alleviated effect of severe work roll wear contours on performance of edge drop control are achieved by the application of ASR with crown control and wear control ability in downstream stand F5 and VCR in all stands of 1 700 mm hot strip mill.
文摘The hardening curve for sheet metal can be determined from the load-displacement curve of tensile specimen with rectangular cross-section. Therefore,uniaxial compression test on cylinder specimen made from laminated sample is put forward. Considering the influence of anisotropy on hardening properties and the stress state in popular forming process,plane strain compression test on cubic specimen made from laminated sample was advanced. Results show that the deformation range of hardening curves obtained from the presented methods is wide,which meets the need for the application in sheet metal forming processes. In view of the characteristics of methods presented in the paper and the stress strain state of various forming processes,the adaptability of the two methods presented in this paper is given.