镁合金精密压铸成形工艺及模具设计制造

本文首先阐述了镁合金精密压铸成形工艺,而后对其模具设计及制造进行了研究,以供参考和借鉴。

热压铸工艺在结构陶瓷生产中的应用

本文结合结构陶瓷的生产 。

锁扣凸台的压凸冷挤复合模设计

针对锁扣凸台强度不足而导致的失效实例,在分析其压凸台模具结构及工作原理的基础上,找出了原压凸成形机理上的缺陷,明确了失效的原因.由此提出了压凸冷挤复合工艺,设计了压凸冷挤复合模,分析了压凸冷挤复合工艺的成形机理.生产实践及强度试验表明:该工艺能满足产品要求,对强度的提高有显著效果.

Optimization of AZ80 magnesium alloy squeeze cast process parameters using morphological matrix

The squeeze cast process parameters of AZ80 magnesium alloy were optimized by morphological matrix. Experiments were conducted by varying squeeze pressure, die pre-heat temperature and pressure duration using L9（33） orthogonal array of Taguchi method. In Taguchi method, a 3-level orthogonal array was used to determine the signal/noise ratio. Analysis of variance was used to determine the most significant process parameters affecting the mechanical properties. Mechanical properties such as ultimate tensile strength, elongation and hardness of the components were ascertained using multi variable linear regression analysis. Optimal squeeze cast process parameters were obtained.

High temperature deformation behavior and optimization of hot compression process parameters in TC11 titanium alloy with coarse lamellar original microstructure

The high temperature deformation behaviors of α＋β type titanium alloy TC11 （Ti-6.5Al-3.5Mo-1.5Zr-0.3Si） with coarse lamellar starting microstructure were investigated based on the hot compression tests in the temperature range of 950-1100 ℃ and the strain rate range of 0.001-10 s-1. The processing maps at different strains were then constructed based on the dynamic materials model, and the hot compression process parameters and deformation mechanism were optimized and analyzed, respectively. The results show that the processing maps exhibit two domains with a high efficiency of power dissipation and a flow instability domain with a less efficiency of power dissipation. The types of domains were characterized by convergence and divergence of the efficiency of power dissipation, respectively. The convergent domain in a＋fl phase field is at the temperature of 950-990 ℃ and the strain rate of 0.001-0.01 s^-1, which correspond to a better hot compression process window of α＋β phase field. The peak of efficiency of power dissipation in α＋β phase field is at 950 ℃ and 0.001 s 1, which correspond to the best hot compression process parameters of α＋β phase field. The convergent domain in β phase field is at the temperature of 1020-1080 ℃ and the strain rate of 0.001-0.1 s^-l, which correspond to a better hot compression process window of β phase field. The peak of efficiency of power dissipation in ℃ phase field occurs at 1050 ℃ over the strain rates from 0.001 s^-1 to 0.01 s^-1, which correspond to the best hot compression process parameters of ,8 phase field. The divergence domain occurs at the strain rates above 0.5 s^-1 and in all the tested temperature range, which correspond to flow instability that is manifested as flow localization and indicated by the flow softening phenomenon in stress-- strain curves. The deformation mechanisms of the optimized hot compression process windows in a＋β and β phase fields are identified to be spheroidizing and dynamic recrystallizing controlled by self-diffusion mechanism, respectively. The microstructure observation of the deformed specimens in different domains matches very well with the optimized results.

基于晶体塑性有限元的转向架盖板压形回弹预测

针对S355J2W钢板材由于具有显著的各向异性而使其在模具压形工艺中的回弹难以预测的问题。以高速动车组转向架侧梁上盖板成形为例,对S355J2W钢的晶粒与织构进行了分析并对其各向异性进行了量化,获得了材料晶体塑性本构模型的关键参数,并使用晶体塑性有限元方法评估了其各向异性的力学性能以及Hill48屈服准则的模型参数。建立了转向架侧梁上盖板压形过程仿真模型,分别采用Von Mises及Hill48屈服准则来模拟工件成形后的应力释放及回弹效应,并开展了侧梁上盖板压形实验进行验证,实验结果和仿真结果吻合。各向同性模型和各向异性模型预测结果的对比表明,采用各向异性材料模型可以更准确地预测侧梁上盖板的回弹。

Multi-objective optimization of stamping forming process of head using Pareto-based genetic algorithm

To obtain the optimal process parameters of stamping forming, finite element analysis and optimization technique were integrated via transforming multi-objective issue into a single-objective issue. A Pareto-based genetic algorithm was applied to optimizing the head stamping forming process. In the proposed optimal model, fracture, wrinkle and thickness varying are a function of several factors, such as fillet radius, draw-bead position, blank size and blank-holding force. Hence, it is necessary to investigate the relationship between the objective functions and the variables in order to make objective functions varying minimized simultaneously. Firstly, the central composite experimental(CCD) with four factors and five levels was applied, and the experimental data based on the central composite experimental were acquired. Then, the response surface model(RSM) was set up and the results of the analysis of variance(ANOVA) show that it is reliable to predict the fracture, wrinkle and thickness varying functions by the response surface model. Finally, a Pareto-based genetic algorithm was used to find out a set of Pareto front, which makes fracture, wrinkle and thickness varying minimized integrally. A head stamping case indicates that the present method has higher precision and practicability compared with the "trial and error" procedure.

Rheo-diecasting of AZ91D magnesium alloy by taper barrel rheomoulding process

A self-developed taper barrel rheomoulding(TBR)machine was introduced,and the rheo-diecasting process was implemented by combining TBR machine with the high pressure die casting(HPDC)machine.Microstructural characteristics of the rheo-diecasting components were investigated at different rotation speeds.Flow characteristics and microstructural evolution of the semi-solid slurry during the rheo-diecasting process were analyzed and the mechanical properties of the rheo-diecasting components were studied.The experimental results show that the process is able to obtain such components in which the primaryα-Mg particles are fine,nearly spherical and uniformly distributed in the matrix.When the rotation speed of internal taper barrel is 700 r/min,the primaryα-Mg particles get a mean diameter of about 45μm and a shape factor of about 0.81.The magnesium alloy melt has complex stirring-fixed flow characteristics when flowing in TBR machine.Compared with conventional die-casing process,the rheo-diecasting process can improve the mechanical properties of components;especially,the elongation is improved by 80%.

Research on technological parameters of pressure forming with hot granule medium on AA7075 sheet

Hot granule medium pressure forming （HGMF） process is a new process in which granule medium replaces the medium in existing flexible-die hot forming process, such as liquids, gases or viscous medium. Hot forming of light alloy sheet parts can be realized based on the properties of granule medium, such as withstanding high temperature and pressure, filling well, sealing and loading easily. In this work, the forming of AA7075 cylindrical parts by HGMF process is taken as an example to establish the constitutive relation and forming limit diagram （FLD） of AA7075 sheet which is related to temperature by hot uniaxial tensile test of sheet metal. Based on the assumption that granule medium is applied to extended Drucker-Prager linear material model, the finite element model of HGMF process is established and the effect of technological parameters, such as forming temperature, blank-holder gap and drawing ratio, on the sheet metal formability, is studied. The limit drawing ratio curve of AA7075 cylindrical parts at forming temperature of 175-300 ℃ is obtained by HGMF process test, and the limit drawing ratio reaches the maximum value of 1.71 at 250 ℃. The results of numerical simulation are consistent with the results of process test, and the forming force, distribution of wall thichness and form of instability are predicted correctly, which provides reference for the application of HGMF process.

Influence of rheo-diecasting processing parameters on microstructure and mechanical properties of hypereutectic Al-30%Si alloy

The effects of pouring temperature,vibration frequency,and the number of curves in a serpentine channel,on themicrostructure and mechanical properties of Al-30%Si alloy processed by rheo-diecasting(RDC)were investigated.The semisolidAl-30%Si alloy slurry was prepared by vibration serpentine channel pouring(VSCP)process in the RDC process.The results showthat the pouring temperature,the vibration frequency,and the number of the curves strongly affect the microstructure and mechanicalproperties of Al-30%Si alloy.Under experimental conditions of a pouring temperature of850°C,a twelve-curve copper channel anda vibration frequency of80Hz,the primary Si grains are refined into fine compact grains with average grain size of about24.6μm inthe RDC samples assisted with VSCP.Moreover,the ultimate tensile strength(UTS),elongation and hardness of the RDC sample are296MPa,0.87%and HB155,respectively.It is concluded that the VSCP process can effectively refine the primary Si grains.Therefinement of primary Si grains is the major cause for the improvement of the mechanical properties of the RDC sample.

Ti_(2)AlNb金属间化合物薄壁构件虚拟塑性加工系统

虚拟塑性加工通过在数字空间构建构件加工全过程的数字孪生体,可以实现构件形状尺寸、微观组织和力学性能的仿真,为塑性加工工艺的设计提供了一种高效的方法。针对多相金属间化合物成形与控性一体化的难题,基于有限元软件和自主开发的组织-性能预测工具箱建立了一套全流程虚拟加工系统,实现了塑性加工全流程的模拟和构件形状尺寸、组织和力学性能的预测。设计了具有特定形状尺寸、微观组织和性能要求的Ti_(2)AlNb合金矩形截面件胀-压复合热态气压成形及后续热处理工艺,一次成形实验生产出满足要求的构件。

Reducing residual distortion of thin-plate weldments by rotating extrusion

A new method named rotating extrusion was developed to mitigate residual distortion of thin-plate weldments. The basic principle and characteristic of rotating extrusion as well as an efficient rotating extrusion device were introduced. Systematic trials were conducted to investigate the influence of several technological parameters including the distance between the extrusion tool and welding torch, the pressure acting on weldment, the dimension of the extrusion tool and its rotational speed on distortion control effect. Experimental results show that, as for 2A12T4 aluminum alloy weldment with 2 mm in thickness, 150 mm in width and 350 mm in length, when appropriate technological parameters are adopted, rotating extrusion can reduce its buckling deflection to below 3% of the original value. Implementing rotating extrusion during welding with an extrusion tool more than 100 mm away from the welding torch may achieve better distortion mitigation effect.

Warm hydroforming of magnesium alloy tube with large expansion ratio

Process of warm tube hydroforming was experimentally investigated for forming an AZ31B magnesium alloy tubular part with a large expansion ratio. Effects of temperature on the mechanical properties and formability were studied by uniaxial tensile test and hydraulic bulge test. Total elongation increases with temperature up to 250℃, but uniform elongation and maximum expansion ratio get the highest value at 175℃. Different axial feeding amounts were applied in experiments to determine the reasonable loading path. A preform with useful wrinkles was then realized and the tubular part with an expansion ratio of 50% was formed. Finally, mechanical condition to produce useful wrinkles is deduced and the result illustrates that useful wrinkles are easier to be obtained for tube with higher strain hardening coefficient value and tubular part with smaller expansion ratio.

Effects of process parameters and die geometry on longitudinal welds quality in aluminum porthole die extrusion process

By using the rigid-visco-plasticity finite element method, the welding process of aluminum porthole die extrusion to form a tube was simulated based on Deform-3D software. The welding chamber height （H）, back dimension of die leg （D）, process velocity and initial billet temperature were used in FE simulations so as to determine the conditions in which better longitudinal welding quality can be obtained. According to K criterion, the local welding parameters such as welding pressure, effective stress and welding path length on the welding plane are linked to longitudinal welds quality. Simulation turns out that pressure-to-effective stress ratio （ρ/σ） and welding path length （L） are the key factors affecting the welding quality, Higher welding chamber best and sharper die leg give better welding quality. When H=10 mm and D=0.4 mm, the longitudinal welds have the best quality. Higher process velocity decreases welds quality. The proper velocity is 10 mm/s for this simulation. In a certain range, higher temperature is beneficial to the longitudinal welds. It is found that both 450 and 465℃ can satisfy the requirements of the longitudinal welds.