An RF bandpass filter with a Q-enhancement active inductor is presented. The design technique for a tunable Q-enhancement CMOS active inductor operating in the wide RF-band is described. Moreover,issues related to noi...An RF bandpass filter with a Q-enhancement active inductor is presented. The design technique for a tunable Q-enhancement CMOS active inductor operating in the wide RF-band is described. Moreover,issues related to noise and stability of the active inductor are explained. The filter was fabricated in 0.18μm CMOS technolo- gy,and the circuit occupied an active area of only 150μm ×200μm. Measurement results show that the filter centered at 2. 44GHz with about 60MHz bandwidth （3dB） is tunable in center frequency from about 2.07 to 2. 44GHz. The ldB compression point is - 15dBm while consuming 10. 8mW of DC power,and a maximum quality factor of 103 is attained at the center frequency of 2.07GHz.展开更多
Finite element(FEM)analysis was used to systematically evaluate the inhomogeneity of deformation in cylindrical samples with various sample-anvil friction coefficients,m.It was found that the level of friction strongl...Finite element(FEM)analysis was used to systematically evaluate the inhomogeneity of deformation in cylindrical samples with various sample-anvil friction coefficients,m.It was found that the level of friction strongly influences the deformation homogeneity,which increases significantly with the friction coefficient although the overall geometry of the samples almost remains the same when m >0.4.The position,at which the effective strain along the maximum radial direction in a compressed sample is equal to the equivalent strain of the sample,does not vary greatly with respect to both equivalent strain of the sample and m.Hardness measurements of compressed cylindrical 5056B Al alloy samples revealed a change of effective strain distribution similar to that revealed by FEM analysis.There exists a quantitative relationship between the hardness and the effective strain if no recrystallization or recovery occurs during the compression process.展开更多
The uniaxial compression tests of cylinder standard specimens and different dimension cube specimens of No.13 coal seam of Jianxin Colliery were carried out using MTS, and the basic mechanics parameters of Jianxin Col...The uniaxial compression tests of cylinder standard specimens and different dimension cube specimens of No.13 coal seam of Jianxin Colliery were carried out using MTS, and the basic mechanics parameters of Jianxin Colliery 13 coal were studied. The dimension-form effect of uniaxial compression strength was analyzed. The exponent formula σc=6.928＋130.269 8 exp（-0.105 95D）of dimension effect was fitted. While the side length of specimen reaches 80 mm, its unaxial strength tends to a stable value which is called to be the strength of coal mass. Studies indicates that since the cube specimen suffered more shake than the cylinder one during machining and processing and the stress is centralized at four corners of cube during compressive experiment, the coal strength of standard cylinder specimen is higher than that of cube one.展开更多
文摘An RF bandpass filter with a Q-enhancement active inductor is presented. The design technique for a tunable Q-enhancement CMOS active inductor operating in the wide RF-band is described. Moreover,issues related to noise and stability of the active inductor are explained. The filter was fabricated in 0.18μm CMOS technolo- gy,and the circuit occupied an active area of only 150μm ×200μm. Measurement results show that the filter centered at 2. 44GHz with about 60MHz bandwidth （3dB） is tunable in center frequency from about 2.07 to 2. 44GHz. The ldB compression point is - 15dBm while consuming 10. 8mW of DC power,and a maximum quality factor of 103 is attained at the center frequency of 2.07GHz.
基金Project(2016JJ1016) supported by the Science Fund for Distinguished Young Scholars of Hunan Province,ChinaProject(201301G0105337290) supported by the Program of Innovation and Entrepreneur Team Introduced by Guangdong Province,China
文摘Finite element(FEM)analysis was used to systematically evaluate the inhomogeneity of deformation in cylindrical samples with various sample-anvil friction coefficients,m.It was found that the level of friction strongly influences the deformation homogeneity,which increases significantly with the friction coefficient although the overall geometry of the samples almost remains the same when m >0.4.The position,at which the effective strain along the maximum radial direction in a compressed sample is equal to the equivalent strain of the sample,does not vary greatly with respect to both equivalent strain of the sample and m.Hardness measurements of compressed cylindrical 5056B Al alloy samples revealed a change of effective strain distribution similar to that revealed by FEM analysis.There exists a quantitative relationship between the hardness and the effective strain if no recrystallization or recovery occurs during the compression process.
文摘The uniaxial compression tests of cylinder standard specimens and different dimension cube specimens of No.13 coal seam of Jianxin Colliery were carried out using MTS, and the basic mechanics parameters of Jianxin Colliery 13 coal were studied. The dimension-form effect of uniaxial compression strength was analyzed. The exponent formula σc=6.928＋130.269 8 exp（-0.105 95D）of dimension effect was fitted. While the side length of specimen reaches 80 mm, its unaxial strength tends to a stable value which is called to be the strength of coal mass. Studies indicates that since the cube specimen suffered more shake than the cylinder one during machining and processing and the stress is centralized at four corners of cube during compressive experiment, the coal strength of standard cylinder specimen is higher than that of cube one.
