This study aims to examine and analyze the effect of corrosion wastage on the ship hull of a double hull very large crude oil carrier. To calculate the ultimate bending moment capacity, along with the neutral axis pos...This study aims to examine and analyze the effect of corrosion wastage on the ship hull of a double hull very large crude oil carrier. To calculate the ultimate bending moment capacity, along with the neutral axis position at the limit state, section modulus, and moment of inertia, the incremental-iterative method is employed. This paper also considered the residual strength checking criteria of ship hull and the ultimate stress behaviors of the representative structural elements. Then, Paik's probabilistic corrosion, which employs two levels of corrosion rate and three different assumptions of coating life time, is applied to assess the corrosion effects. The calculation results obtained through relevant analyses are also presented.展开更多
The vacuum residual from Iranian Light crude oil are separated into a series of 16 narrow fractions according to the molecular weight by the supercritical fluid extraction and fractional (SFEF) technology. The chemica...The vacuum residual from Iranian Light crude oil are separated into a series of 16 narrow fractions according to the molecular weight by the supercritical fluid extraction and fractional (SFEF) technology. The chemical element and the UV spectrum of each fraction are analyzed. The effects of several factors on the interfacial tension are investigated, which are the fraction concentration in oil phase, the ratio of oil component, the salts dissolved in the water phase and the pH value. The interfacial tension decreases rapidly as the concentration of the residual fraction in the oil increases, showing a higher interfacial activity of the fraction. The interfacial tension changes, as the amount of absorption or the state of the fractions in the interface changes resulting from different ratios of oil, different kinds or concentrations of salts in water, and different pH values. It is concluded that the interfacial tension changes regularly, corresponding to the regular molecular parameters of the vacuum residual fractions.展开更多
Removal of water contained in extra-viscous crude oil is quite difficult because of the high viscosity and high resins content of heavy oil.The microwave technology was introduced for the separation of water from high...Removal of water contained in extra-viscous crude oil is quite difficult because of the high viscosity and high resins content of heavy oil.The microwave technology was introduced for the separation of water from high-viscosity crude oil in the presence of sodium acetate.The decrease in zeta-potential of interface and the viscosity of crude oil are responsible for the accelerated separation of water under microwave irradiation.The influences of the concentration of sodium acetate in sample,irradiation pressure,irradiation time and irradiation power on the separation efficiency were investigated.The optimum technological condition for the refining process was determined.Upon treating the sample 1 (with a water concentration of 50%),the water removal rate was 98.44%,when the optimum conditions were identified to be a sodium acetate concentration of 2%,an irradiation pressure of 0.1 MPa,an irradiation time of 2 min,and an irradiation power of 225 W,with the recovery of sodium acetate reaching 97.88%.Upon treating the sample 2 (the concentration of water was 20%),the water removal rate was 93.85%,when the optimum conditions were determined to be a sodium acetate concentration of 3%,an irradiation pressure of 0.1 MPa,an irradiation time of 4 min,and an irradiation power of 375 W,with the recovery of sodium acetate reaching 93.54%.By using this method,the dehydration efficiency was increased rapidly.展开更多
The Bakken formation has become a prominent oil resource for south-east Saskatchewan, especially with the advent of horizontal well technology and new hydraulic fracturing methods. As more wells are drilled, there is ...The Bakken formation has become a prominent oil resource for south-east Saskatchewan, especially with the advent of horizontal well technology and new hydraulic fracturing methods. As more wells are drilled, there is a desire to determine whether there is potential for improved oil recovery and to evaluate the economic feasibility. This paper evaluates the benefit of implementing waterflooding, CO2 injection or WAG （water-alternating-gas） recovery methods for improved oil recovery of the Bakken formation. A simulation model resembling the study area was built using CMG-GEM （computer modeling group-generalized equation of state model） reservoir simulation package and a history match of the primary recovery data available was performed. Based on the simulation results, it was concluded that waterflooding had a significant influence on the oil recovery factor, although COz provided the highest increase in crude oil recovery, The capital expenditure for surface facilities and cost of injected fluid was the most economically viable for implementation of waterflooding. The WAG injection simulation results were similar to CO2 injection, except that reservoir pressure was able to be better maintained. Given that high-quality source water is available, waterflooding is the most economically feasible choice according to the simulation results obtained from this study.展开更多
Rate transient method is a recently-developed performance analysis tool specially designed for low-permeability or tight gas reservoirs. This method, theoretically based on pressure transient analysis, integrates mate...Rate transient method is a recently-developed performance analysis tool specially designed for low-permeability or tight gas reservoirs. This method, theoretically based on pressure transient analysis, integrates material balance principle and the concept of material balance pseudo-time proposed by Blansingame. With daily production data of gas well, it could be used to calculate OGIP, current formation pressure, permeability, skin factor, to identify complex geologic boundaries, to determine whether drainage boundary has been reached, to calculate drainage area and drainage radius for single well and to predict performance. It has been extensively employed in more than ten low-permeability gas fields. It proves that most problems in performance analysis for low permeability gas reservoirs could be solved by this method. Field practices show great economical benefits could be achieved by employing this method in gas field development.展开更多
文摘This study aims to examine and analyze the effect of corrosion wastage on the ship hull of a double hull very large crude oil carrier. To calculate the ultimate bending moment capacity, along with the neutral axis position at the limit state, section modulus, and moment of inertia, the incremental-iterative method is employed. This paper also considered the residual strength checking criteria of ship hull and the ultimate stress behaviors of the representative structural elements. Then, Paik's probabilistic corrosion, which employs two levels of corrosion rate and three different assumptions of coating life time, is applied to assess the corrosion effects. The calculation results obtained through relevant analyses are also presented.
基金Supported by the National Key Basic Research Programme (No.973-G1999022505),University of Petroleum Basic Research Fund(No.ZX9904)
文摘The vacuum residual from Iranian Light crude oil are separated into a series of 16 narrow fractions according to the molecular weight by the supercritical fluid extraction and fractional (SFEF) technology. The chemical element and the UV spectrum of each fraction are analyzed. The effects of several factors on the interfacial tension are investigated, which are the fraction concentration in oil phase, the ratio of oil component, the salts dissolved in the water phase and the pH value. The interfacial tension decreases rapidly as the concentration of the residual fraction in the oil increases, showing a higher interfacial activity of the fraction. The interfacial tension changes, as the amount of absorption or the state of the fractions in the interface changes resulting from different ratios of oil, different kinds or concentrations of salts in water, and different pH values. It is concluded that the interfacial tension changes regularly, corresponding to the regular molecular parameters of the vacuum residual fractions.
基金the financial support of Liaoning Province Education Department Project(2004D06)
文摘Removal of water contained in extra-viscous crude oil is quite difficult because of the high viscosity and high resins content of heavy oil.The microwave technology was introduced for the separation of water from high-viscosity crude oil in the presence of sodium acetate.The decrease in zeta-potential of interface and the viscosity of crude oil are responsible for the accelerated separation of water under microwave irradiation.The influences of the concentration of sodium acetate in sample,irradiation pressure,irradiation time and irradiation power on the separation efficiency were investigated.The optimum technological condition for the refining process was determined.Upon treating the sample 1 (with a water concentration of 50%),the water removal rate was 98.44%,when the optimum conditions were identified to be a sodium acetate concentration of 2%,an irradiation pressure of 0.1 MPa,an irradiation time of 2 min,and an irradiation power of 225 W,with the recovery of sodium acetate reaching 97.88%.Upon treating the sample 2 (the concentration of water was 20%),the water removal rate was 93.85%,when the optimum conditions were determined to be a sodium acetate concentration of 3%,an irradiation pressure of 0.1 MPa,an irradiation time of 4 min,and an irradiation power of 375 W,with the recovery of sodium acetate reaching 93.54%.By using this method,the dehydration efficiency was increased rapidly.
文摘The Bakken formation has become a prominent oil resource for south-east Saskatchewan, especially with the advent of horizontal well technology and new hydraulic fracturing methods. As more wells are drilled, there is a desire to determine whether there is potential for improved oil recovery and to evaluate the economic feasibility. This paper evaluates the benefit of implementing waterflooding, CO2 injection or WAG （water-alternating-gas） recovery methods for improved oil recovery of the Bakken formation. A simulation model resembling the study area was built using CMG-GEM （computer modeling group-generalized equation of state model） reservoir simulation package and a history match of the primary recovery data available was performed. Based on the simulation results, it was concluded that waterflooding had a significant influence on the oil recovery factor, although COz provided the highest increase in crude oil recovery, The capital expenditure for surface facilities and cost of injected fluid was the most economically viable for implementation of waterflooding. The WAG injection simulation results were similar to CO2 injection, except that reservoir pressure was able to be better maintained. Given that high-quality source water is available, waterflooding is the most economically feasible choice according to the simulation results obtained from this study.
文摘Rate transient method is a recently-developed performance analysis tool specially designed for low-permeability or tight gas reservoirs. This method, theoretically based on pressure transient analysis, integrates material balance principle and the concept of material balance pseudo-time proposed by Blansingame. With daily production data of gas well, it could be used to calculate OGIP, current formation pressure, permeability, skin factor, to identify complex geologic boundaries, to determine whether drainage boundary has been reached, to calculate drainage area and drainage radius for single well and to predict performance. It has been extensively employed in more than ten low-permeability gas fields. It proves that most problems in performance analysis for low permeability gas reservoirs could be solved by this method. Field practices show great economical benefits could be achieved by employing this method in gas field development.
