The flow fields in a dual Rushton impeller stirred tank with diameter of 0.48 m （T） were measured by using Particle Image Velocimetry （PIV）. Three different size impellers were used in the experiments with diamete...The flow fields in a dual Rushton impeller stirred tank with diameter of 0.48 m （T） were measured by using Particle Image Velocimetry （PIV）. Three different size impellers were used in the experiments with diameters of D = 0.33T, 0.40T and 0.50T, respectively. The multi-block and 360° ensemble-averaged approaches were used to measure the radial and axial angle-resolved velocity distributions. Three typical flow patterns, named, merging flow, parallel flow and diverging flow, were obtained by changing the clearance of the bottom impeller above the tank base （C1） and the spacing between the two impellers （C2）. The results show that while C1 is equal to D, the parallel flow occurs as C2≥0.40T, C2≥0.38T and C2≥0.32T and the merging flow occurs as C2≤0.38T, C2≤0.36T and C2≤0.27T for the impellers with diameter of D=0.33T, 0.40T and 0.50T, respectively. When C2 is equal to D, the diverging flow occurs in the value of C1≤0.15T for all three impellers. The flow numbers of these impellers were calculated for the parallel flow. Trailing vortices generated by the lower impeller for the diverging flow were shown by the 10° angle-resolved velocity measurements. The peak value of turbulence kinetic energy （ k/V^2tip = 0.12-0.15 or above） appears along the center of the impeller discharging stream.展开更多
Particle Image Velocimetry （PIV） has been used to investigate turbulence characteristics in a 0.48 m diameter stirred vessel filled to a liquid height （ H = 1.4T ） of 0.67 m. The agitator had dual Rushton impeller...Particle Image Velocimetry （PIV） has been used to investigate turbulence characteristics in a 0.48 m diameter stirred vessel filled to a liquid height （ H = 1.4T ） of 0.67 m. The agitator had dual Rushton impellers of 0.19 m diameter （ D = 0.4T ）. The developed flow patterns depend on the clearance of the lower impeller above the base of the vessel, the spacing between the two impellers, and the submergence of the upper impeller below the liq- uid surface. Their combinations can generate three basic flow patterns, named, parallel, merging and diverging flows. The results of velocity measurement show that the flow characteristics in the impeller jet flow region changes very little for different positions. Average velocity, trailing vortices and shear strain rate distributions for three flow patterns were measured by using PIV technique. The characteristics of trailing vortex and its trajectory were described in detail for those three flow patterns. Since the space-resolution of PIV can only reach the sub-grid rather than the Kolmogorov scale, a large-eddy PIV analysis has been used to estimate the distribution of the turbulent kinetic energy dissipation. Comparison of the distributions of turbulent kinetic energy and dissipation rate in merging flow shows that the highest turbulent kinetic energy and dissipation are both located in the vortex regions, but the maxima are at somewhat different lo- cations behind the blade. About 37% of the total energy is dissipated in dual impeller jet flow regions. The obtained distribution of shear strain rate for merging flow is similar to that of turbulence dissipation, with the shear strain rate around the trailing vortices much higher than in other areas.展开更多
基金Supported by the National Natural Science Foundation of China （20776008）and the National Basic Research Program of China （2007CB714300）.
文摘The flow fields in a dual Rushton impeller stirred tank with diameter of 0.48 m （T） were measured by using Particle Image Velocimetry （PIV）. Three different size impellers were used in the experiments with diameters of D = 0.33T, 0.40T and 0.50T, respectively. The multi-block and 360° ensemble-averaged approaches were used to measure the radial and axial angle-resolved velocity distributions. Three typical flow patterns, named, merging flow, parallel flow and diverging flow, were obtained by changing the clearance of the bottom impeller above the tank base （C1） and the spacing between the two impellers （C2）. The results show that while C1 is equal to D, the parallel flow occurs as C2≥0.40T, C2≥0.38T and C2≥0.32T and the merging flow occurs as C2≤0.38T, C2≤0.36T and C2≤0.27T for the impellers with diameter of D=0.33T, 0.40T and 0.50T, respectively. When C2 is equal to D, the diverging flow occurs in the value of C1≤0.15T for all three impellers. The flow numbers of these impellers were calculated for the parallel flow. Trailing vortices generated by the lower impeller for the diverging flow were shown by the 10° angle-resolved velocity measurements. The peak value of turbulence kinetic energy （ k/V^2tip = 0.12-0.15 or above） appears along the center of the impeller discharging stream.
基金Supported by the National Natural Science Foundation of China （20776008, 20821004） and the National Basic Research Program of China （2007CB714300）.
文摘Particle Image Velocimetry （PIV） has been used to investigate turbulence characteristics in a 0.48 m diameter stirred vessel filled to a liquid height （ H = 1.4T ） of 0.67 m. The agitator had dual Rushton impellers of 0.19 m diameter （ D = 0.4T ）. The developed flow patterns depend on the clearance of the lower impeller above the base of the vessel, the spacing between the two impellers, and the submergence of the upper impeller below the liq- uid surface. Their combinations can generate three basic flow patterns, named, parallel, merging and diverging flows. The results of velocity measurement show that the flow characteristics in the impeller jet flow region changes very little for different positions. Average velocity, trailing vortices and shear strain rate distributions for three flow patterns were measured by using PIV technique. The characteristics of trailing vortex and its trajectory were described in detail for those three flow patterns. Since the space-resolution of PIV can only reach the sub-grid rather than the Kolmogorov scale, a large-eddy PIV analysis has been used to estimate the distribution of the turbulent kinetic energy dissipation. Comparison of the distributions of turbulent kinetic energy and dissipation rate in merging flow shows that the highest turbulent kinetic energy and dissipation are both located in the vortex regions, but the maxima are at somewhat different lo- cations behind the blade. About 37% of the total energy is dissipated in dual impeller jet flow regions. The obtained distribution of shear strain rate for merging flow is similar to that of turbulence dissipation, with the shear strain rate around the trailing vortices much higher than in other areas.
