一种用于Bluetooth发接器的倍频式VCO

介绍了一种适用于 Bluetooth发接器的 ,可以单片集成的倍频式压控振荡器 ( VCO)。这种 VCO由两部分组成 ,主 VCO的振荡频率是所需本振频率的一半 ,然后采用“注入锁频”原理对主 VCO的振荡频率进行倍频以产生本振信号。主 VCO和倍频电路都使用了片上集成螺旋电感 ,调谐用的变容元件使用 PMOS晶体管实现。经过版图设计和后仿真 ,在 TSMC0 .35 μm数字 COMS工艺 ,3.3V电源电压下 ,该 VCO在 2 .4GHz中心频率附近可以达到的相位噪声指标为 -1 2 5 d Bc/Hz( 60 0 k Hz) ,在输出摆幅为 60 0 m Vp- p时 ,功耗为 2 2 m W。

用于2.5Gbps千兆以太网发接器的时钟倍频器设计

提出了一种电荷泵锁相环电路实现的适用于 2 .5Gbps千兆以太网发接器要求的高速时钟倍频器的设计方法。为了获得高速时钟 ,设计中采用了双环路的 VCO结构 ,并且运用动态 D触发器来实现高速分频器。同时为了使得 PLL性能更加稳定 ,对电路作了进一步改进 :在 VCO的延迟单元中加了温度补偿部分 ,又采用箝位技术消除电荷泵中电荷重新分配引入的影响。运用 UMC0 .18μm,1.8V CMOS工艺模型 ,在 Cadence的环境下用 spectre S仿真器模拟 ;结果表明设计的时钟倍频电路对于不同的 PV T( P表示工艺变化引起的模型参数的变化 ,VT表示系统工作条件温度和电源电压的变化 )均能得到符合满足 2 .5Gbps千兆以太网发接器要求的时钟倍频信号 ,即使在最坏情况下电路也能保持很好的相位跟踪特性 ,输出静态相位误差平均为 50 ps,整个电路的功耗平均为 35m W。

一种用于千兆以太网发接器的高速串-并转换电路

高速串-并转换电路是数字基带传输系统中的重要单元。在对几种常见串-并转换电路的结构和性能进行比较的基础上,利用动态D触发器实现了一种简单实用的结构,并用它设计了适用于千兆以太网发接器的串-并转换电路。同时,对电路中可能存在的问题,如时钟信号的分布,以及动态单元的电荷泄漏,进行了讨论。

2.5Gbps发接器系统均衡器电路的设计

采用片上可编程均衡技术 ,设计了用于数据率为 2 .5 Gbps发接器系统接收端的均衡器电路。电路采用 0 .1 8μm标准 CMOS工艺和 1 .8V单电源。用 UMC模型 Cadence Spectre S软件进行了仿真 ,电路在 0～1 2 5°C范围内 ,三种工艺角和电源电压变化± 1 0 %的条件下能够正确地工作。在 1 .8V电源、75°C和 tt工艺角条件下 ,电路的总功耗为 40 m W。

2.5Gbps发接器系统接口电路的设计

采用片上阻抗匹配技术和接收端片上可编程均衡技术,设计了用于数据率为2.5Gbps发接器系统的接口电路——发送端的线驱动器和接收端的均衡器电路。基于UMC 0.18μm标准CMOS工艺模型,用CadenceSpetreS仿真器仿真了电路。电路在0℃～125℃范围内,3种工艺角和电源电压变化±10％的条件下能够正确地工作。在1.8V单电源电压下,电路的总功耗为70mW。

Design calculation of porous ceramics tube type dew point indirect evaporative cooler

To improve the wall surface hydrophilicity of a tube type indirect evaporative cooler,a new method adopting porous ceramics is proposed.This method realizes the combination of porous ceramics and the evaporative cooling technique.The design calculation of the porous ceramics tube type dew point indirect evaporative cooler are carried out from such aspects as the volumes and status parameters of the primary and secondary air,the cooler structure,the heat transfer of the solid porous ceramic tubes and the resistance of the cooler.The calculation results show that the design is reasonable.Finally,based on the design calculation,the porous ceramics tube type dew point indirect evaporative cooler is successfully manufactured.

Array for 980nm Vertical Cavity Surface Emitting Diodes and Detectors

Both the vertical cavity surface emitting diodes and detectors are fabricated by using the epitaxial wafer with resonant cavity structure.Their characteristics are analyzed.The light emitters have high spectral purity of 4 8nm and high electroluminescence intensity of 0 7mW while injection current is 50mA.A 1×16 array of surface emitting light device is tested on line by probes and then used for module.The light detectors have wavelength selectivity and space selectivity.The required difference in input mirror reflectivity between emitters and detectors can easily be achieved though varying the numbers of top DBR period by etching.

Multiparty-Controlled Remote Preparation of Two-Particle State

We propose a scheme for multiparty-controlled remote preparation of the two-particle state by using two non-maximally Greenberger-Horne-Zeilinger states as quantum channel. Our scheme consists of one sender and n remote receivers. It will be shown that the sender can help either one of the n receivers to remotely preparation the original state with the appropriate probability, and the sender Alice＇s two-particle projective measurement and the controllers＇ single-particle product meazurements are needed. We also obtained the probability of the successful remote state preparation.

A compact transmit/receive switch for 2.4 GHz reader-less active RFID tag transceiver

Radio frequency identification(RFID) is a ubiquitous identification technology nowadays. An on-chip high-performance transmit/receive(T/R) switch is designed and simulated in 0.13-μm CMOS technology for reader-less RFID tag. The switch utilizes only the transistor width and length(W/L) optimization, proper gate bias resistor and resistive body floating technique and therefore,exhibits 1 d B insertion loss, 31.5 d B isolation and 29.2 d Bm 1-d B compression point(P1d B). Moreover, the switch dissipates only786.7 n W power for 1.8/0 V control voltages and is capable of switching in 794 fs. Above all, as there is no inductor or capacitor used in the circuit, the size of the switch is 0.00208 mm2 only. This switch will be appropriate for reader-less RFID tag transceiver front-end as well as other wireless transceivers operated at 2.4 GHz band.

P68 RNA helicase is a nucleocytoplasmic shuttling protein

P68 RNA helicase is a prototypical DEAD box RNA helicase. The protein plays a very important role in early organ development and maturation. Consistent with the function of the protein in transcriptional regulation and pre-mRNA splicing, p68 was found to predominately localize in the cell nucleus. However, recent experiments demon- strate a transient cytoplasmic localization of the protein. We report here that p68 shuttles between the nucleus and the cytoplasm. The nucleocytoplasmic shuttling of p68 is mediated by two nuclear localization signal and two nuclear exporting signal sequence elements. Our experiments reveal that p68 shuttles via a classical RanGTPase-dependent pathway.

Thin Emitter Structure Improved Turn-on Characteristics in RSD

The thin emitter structure was introduced into reversely switched dynistor（RSD） to improve its turn-on characteristics. According to the analysis of turn-on condition, thin emitter structure is capable of reducing the extraction action for the triggering plasma layer P1 during turn-on process, and satisfying the requirement that triggering electric charge cannot be exhausted and therefore enables RSD to turn on uniformly. The on-state thin emitter RSD was equivalent to an asymmetric pin diode model. The simulation result shows that the forward voltage drop of RSD falls with the decrease of doping dose in p^＋-emitter in a certain range, and when the doping concentration is extremely tow, the decrease of the width of p^＋-emitter can obtain a tow forward voltage drop. Thin emitter RSD chips were made by sintering AI on n-Si. The test result shows that their turn-on process is uniform and the voltage drop is 7.5 V when the peak conversion current is 5 500 A.

Energy Spectra of Excitons Bound to a Neutral Acceptor in Quantum Dots

The energy spectra of the ground state for an exciton (X) trapped by a neutral acceptor (A0) in a quantum dot with a parabolic confinement have been calculated as a function of the electron-to-hole mass ratio σ by using the hyperspherical coordinates. We find that the (A0,X) complex confined in a quantum dot has in general a larger binding energy than those in a two-dimensional quantum well and a three-dimensional bulk semiconductor, and the binding energy decreases with the increase of the electron-to-hole mass ratio.

Simplified Four-Qubit Cluster State for Splitting Arbitrary Single-Qubit Information

The simplified four-qubit cluster state （i.e., （｜0000〉 ＋ ｜0011〉 ＋ ｜1100〉 -｜1111〉）/2） is explored for splitting an arbitrary single-qubit quantum information （QI）. Various feasible distributions of the four qubits among the Q,I sender and receivers for tri-splitting or hi-splitting are found out. For the distribution representations the corresponding splitting schemes and their LOCCs （local operation and classical communication） are presented amply while others are mentioned concisely.

Study on Restrike Phenomena for 40.5-kV Vacuum Circuit Breakers

When interrupting short circuit fault by 40.5-kV vacuum circuit breakers, it is significant to eliminate multiple restrike phenomena, which occur frequently and result in high overvoltage and even interruption failure. A synthetic circuit that can supply a DC recovery voltage after current zero was used to study multiple restrike phenomena in switching. Some key factors including breaking current, clearance between open contacts, electrode structure and contact material, which may affect restrike characteristics, were studied. Under various clearances, the statistical probability of restrike was obtained. As a result, the best scope of clearance between open contacts was found. The performance of CuCr50/50 and CuCr75/25 material were compared. Two kinds of electrode structures, namely 1/2 coil structure and cup-shaped axial magnetic structure, were tested. After a high-current interruption, conditioning effoct was realized and the probability of restrike decreased.

A Simplified Model for Analysis of Heat and Mass Transfer in an Indirect Evaporative Cooler

A simplified model for analysis of heat and mass transfer between air stream and flowing down water film in counter-flow plate heat exchanger which serves as an indirect evaporative cooler is theoretically analyzed in this paper. Indirect evaporative cooler is used for sensible cooling of air which then is used for air conditioning purposes. Mathematical model was developed allowing determining heat transfer surface, outlet air temperature and specific humidity of the air being cooled. To make the model simpler some simplifications have been incorporated. The model has high level of correctness and can be used to calculate and design different types of evaporative heat exchangers. Analysis of results of calculations by the help of the developed model prove that the surface of heat exchanger depends on the thickness of water film layer by the regularity of direct proportionality. Moreover, increasing of the water film thickness brings to the decreasing of the efficiency of evaporative type heat exchanger. The model can be used for correct calculation and design of an evaporative cooling air conditioning systems.

A new dimmer for alternating-current directly driven light-emitting-diode lamp

A new dimmer using a mental-oxide-semiconductor field-effect transistor (MOSFET) for alternating-current (AC) directly driven light-emitting-diode (LED) lamp was presented. The control method of proposed dimmer is pulse width control (PWM) method. Compared with the conventional phase-controlled dimmer, the proposed PWM dimmer can produce sine wave and did not cause harmonics problem. Furthermore, the proposed control method did not amplify the light flicker due to the independence of input voltage. Therefore, the PWM dimmer can be used as the dimmer of the AC LED lamp instead of the conventional phase-controlled dimmer. The experimental result shows that the proposed PWM dimmer has good performances.

Research on CMOS Mm-Wave Circuits and Systems for Wireless Communications

This paper lenges in the design of discusses some chal- millimeter-wave （mln- wave） circuits and systems for 5th generation （5G） wireless systems in CMOS process. The properties of some passive and active devices such as inductors, capacitors, transmission lines, translbrmers and transistors in mm-wave frequency band are discussed. Self-healing technique dealing with PVT variation, res- onant mode switching technique to enhance frequency tuning range of voltage controlled oscillator （VCO） and dual mode technique for power amplifier （PA） efficiency enhancement are introduced. At last, A fully-integrated 60 GHz 5 Gb/s QPSK transceiver with the transmit/receive （T/R） switch in 65nm CMOS process is introduced. The measured error vector magnitude （EVM） of the TX is -21.9 dB while the bit error rate （BER） of the RX with a -52 dBm sine-wave input is below 8e-7 when transmitting/receiving 5 Gb/s data. The transceiver is powered by 1.0 V and 1.2 V supply （except the phase-frequency detector and charge-pump in the frequency synthesizer which are powered by 2.5 V supply） and con- sumes 135 mW in TX mode and 176 mW in RX mode.

Ionized Acceptor Bound Exciton States in Wurtzite GaN/Al_xGa(1-x)N Cylindrical Quantum Dot

Based on the framework of the effective-mass approximation, the ionized acceptor bound exciton （A- X） binding energy and the emission wavelength are investigated for a cylindrical wurtzite （WZ） GaN/A1x Ga1-xN quantum dot （QD） with finite potential barriers by means of a variational method. Numerical results show that the binding energy and the emission wavelength highly depend on the QD size, the position of the ionized acceptor and the Al composition x of the barrier material AIxGal-xN. The binding energy and the emission wavelength are larger when the acceptor is located in the vicinity of the left interface of the QD. In particular, the binding energy of （ A-, X） complex is insensitive to the dot height when the acceptor is located at the left boundary of the QD. The ionized acceptor bound exciton binding energy and the emission wavelength are both increased if Al composition x is increased.

Research on HJ-1A/B satellite data automatic geometric precision correction design

Developed independently by China,HJ-1A/B satellites have operated well on-orbit for five years and acquired a large number of high-quality observation data.The realization of the observation data geometric precision correction is of great significance for macro and dynamic ecological environment monitoring.The paper analyzed the parameter characteristics of HJ-1 satellite and geometric features of HJ-1 satellite level 2 data(systematic geo- corrected data).Based on this,the overall HJ- 1 multi- sensor geometric correction flow and charge-coupled device(CCD) automatic geometric precision correction method were designed.Actual operating data showed that the method could achieve good result for automatic geometric precision correction of HJ-1 satellite data,automatic HJ-1 CCD image geometric precision correction accuracy could be achieved within two pixels and automatic matching accuracy between the images of same satellite could be obtained less than one pixel.

A novel technology for control of variable speed pumped storage power plant

Variable speed pumped storage machines are used extensively in wind power plant and pumped storage power plant. This paper presents direct torque and flux control(DTFC) of a variable speed pumped storage power plant(VSPSP). By this method both torque and flux have been applied to control the VSPSP. The comparison between VSPSP's control strategies is studied. At the first, a wind turbine with the capacity 2.2 k W and DTFC control strategies simulated then a 250 MW VSPSP is simulated with all of its parts(including electrical, mechanical, hydraulic and its control system) by MATLAB software. In all of simulations, both converters including two-level voltage source converter(2LVSC) and three-level voltage source converter(3LVSC) are applied. The results of applying 2LVSC and 3LVSC are the rapid dynamic responses with better efficiency, reducing the total harmonic distortion(THD) and ripple of rotor torque and flux.