发电机在线检测机器人的分析与实验

在当今电气化时代,发电设备的日常维护和定期检修对保障设备安全具有重大的意义,高效、经济地提供发电设备全生命周期的服务,是发电设备供应商提升其核心竞争能力,提高产品附加值的极佳途径。将发电机检测技术与特种机器人技术相结合,研发了一种发电机在线检测机器人系统,能够在转子不抽离定子的状态下实现可视化检测、槽楔松动检测和定子铁芯电磁缺陷检测(ELCID)的功能。相关试验表明,该系统能够可靠高效地完成发电机检测任务。

基于CAN网络的计算机控制30 kW柴油发电机组测试系统

介绍了基于CAN网络传递数据的30kW柴油发电机组测试系统结构,阐述了其软、硬件组成与特点。试验表明:测试系统能很好地解决30kW柴油发电机组的调试与试验问题。

日超导发电机与输电网试联成功

本刊讯 据新华社6月23日消息,日本不久前进行了超导发电机与商业输电网联网的试验,获得成功。 这次试验是由一个名为“超导发电机器与材料技术研究组合”的科研联合体于今年5、6月间进行的。 据时事社最近报道,这个由16家企业组成的联合攻关机构已经制造出3台输出功率超过7万千瓦的超导发电机,在最大输出功率、连续运转时间等方面均处于世界领先地位。这次联网试验使用的发电机就是其中一台。 研究人员将超导发电机与7万伏商业输电网相连,试验共进行了53小时。结果表明,超导发电机运转稳定,并且还可以随着电力消费的增减而调整电压。 这家科研联合体认为,此次试验的成功使人们看到了在2010年前后实现超导发电实用化的希望,今后它打算设计制造功率为20万千瓦的超导发电设备。 超导发电机是日本通产省新能源计划“阳光计划”的主要课题之一,从1988年开始研究开发。

Low Voltage CMOS Gilbert Mixers for Bluetooth Transceiver

Based on the analyses of the reported Gilbert mixers operating at low supply vol tage,a down-conversion mixer and an up-conversion mixer for 2.4GHz bluetooth transceiver are presented with the modified low voltage design techniques,respe ctively.Feedback and current mirror techniques suitable for low voltage operatio n are used to improve the linearity of the up-conversion mixer,and folded-casc ode output stage is adopted to optimize the noise and conversion gain of the dow n-conversion mixer operating at low voltage.Based on 0.35μm CMOS technology,s imulations are performed with 2V supply voltage.The results show that 20dBm thir d-order intercept point (IIP3),87mV output signal amplitude are achieved for up -conversion mixer with about 3mA current;while 20dB conversion gain (CG),6.5nV /Hz input-referred noise,4.4dBm IIP3 are obtained for down-conversion mixer with about 3.5mA current.

Numerical Study of Optimization of Layer Thickness in Bilayer Organic Light-Emitting Diodes

A numerical model for bilayer organic light-emitting diodes (OLEDs) is developed under the basis of trapped charge limited conduction.The dependences of the current density on the layer thickness,trap properties and carrier mobility of the hole transport layer (HTL) and emission layer (EML) in bilayer OLEDs of the structure anode/HTL/EML/cathode are numerically investigated.It is found that,for given values of the total thickness of organic layers,reduced depth of trap,total density of trap,and carrier mobility of HTL as well as EML,there exists an optimal thickness ratio of HTL to EML,by which a maximal quantum efficiency can be achieved.Through optimization of the thickness ratio,an enhancement of current density and quantum efficiency of as much as two orders of magnitude can be obtained.The dependences of the optimal thickness ratio to the characteristic trap energy,total density of trap and carrier mobility are numerically analyzed.

OPTIMAL DESIGN OF DUAL STATOR-WINDING INDUCTION GENERATOR WITH PWM CONVERTER

To minimize the reactive power of the converter of the control winding in the novel dual stator-winding induction generator based on the PWM converter, design features of the induction generator with a rectified load are proposed. The optimization method of excited capacitors to minimize the reactive power of the control winding at a variable speed is given. The calculation capacity of the machine with a diode bridge rectifier load is proposed. To achieve global searching, the integrated method with the improved real-coded genetic algorithm and the twodimensional finite element method （FEM） is introduced. Design results of the sample show that reactive power can be reduced by the method, and the converter capacity can be decreased to 1/3 of output rated power at the speed ratio of 1 ： 3, thus reducing the volume and the mass of the inverter.

INVESTIGATION IN REDUCING EXHAUST EMISSIONS FROM TWO STROKE MOTORCYCLES

Test results of reducing two stroke motorcycle emissions with new type carburettors and electronic fuel injection systems are presented. Analyses and comparison between different systems are discussed. The adoption of electronically controlled injection and corresponding electronic control technique is an effective measure of prolonged vitality to improve emissions from two stroke motorcycles. Suggestions about the strategic steps of China′s motorcycle emission control are proposed.

A Hybrid Random Number Generator Using Single Electron Tunneling Junctions and MOS Transistors

This paper proposes a novel single electron random number generator （RNG）. The generator consists of multiple tunneling junctions （MTJ） and a hybrid single electron transistor （SET）/MOS output circuit. It is an oscillator-based RNG. MTJ is used to implement a high-frequency oscillator, which uses the inherent physical randomness in tunneling events of the MTJ to achieve large frequency drift. The hybrid SET and MOS output circuit is used to amplify and buffer the output signal of the MTJ oscillator. The RNG circuit generates high-quality random digital sequences with a simple structure. The operation speed of this circuit is as high as 1GHz. The circuit also has good driven capability and low power dissipation. This novel random number generator is a promising device for future cryptographic systems and communication applications.

Enhanced control of DFIG-used back-to-back PWM VSC under unbalanced grid voltage conditions

This paper presents a unified positive-and negative-sequence dual-dq dynamic model of wind-turbine driven doubly-fed induction generator(DFIG) under unbalanced grid voltage conditions. Strategies for enhanced control and operation of a DFIG-used back-to-back(BTB) PWM voltage source converter(VSC) are proposed. The modified control design for the grid-side converter in the stationary αβ frames diminishes the amplitude of DC-link voltage ripples of twice the grid frequency,and the two proposed control targets for the rotor-side converter are alternatively achieved,which,as a result,improve the fault-ride through(FRT) capability of the DFIG based wind power generation systems during unbalanced network supply. A complete unbalanced control scheme with both grid-and rotor-side converters included is designed. Finally,simulation was carried out on a 1.5 MW wind-turbine driven DFIG system and the validity of the developed unified model and the feasibility of the proposed control strategies are all confirmed by the simulated results.

Adaptive rotor current control for wind-turbine driven DFIG using resonant controllers in a rotor rotating reference frame

This paper proposes an adaptive rotor current controller for doubly-fed induction generator (DFIG), which consists of a proportional (P) controller and two harmonic resonant (R) controllers implemented in the rotor rotating reference frame. The two resonant controllers are tuned at slip frequencies ωslip+ and ωslip-, respectively. As a result, the positive- and negative-sequence components of the rotor current are fully regulated by the PR controller without involving the positive- and negative-sequence decomposition, which in effect improves the fault ride-through (FRT) capability of the DFIG-based wind power generation system during the period of large transient grid voltage unbalance. Correctness of the theoretical analysis and feasibility of the proposed unbalanced control scheme are validated by simulation on a 1.5-MW DFIG wind power generation system.

Design of speed controller for electronic fuel injection gasoline generator based on feed-forward PID control

As for the application of electronic fuel injection （EFI） system to small gasoline generator set, mechanical speed controller cannot be coupled with EFI system and has the shortcomings of lagged regulation and poor accuracy, a feed-forward control strategy based on load combined with proportional-integral-differential （PID） control strategy was proposed, and a digital speed controller applied to the electrical control system was designed. The detailed control strategy of the controller was intro- duced. The hardware design for the controller and the key circuits of motor driving, current sampling and angular signal captu- ring were given, and software architecture was discussed. Combined with a gasoline generator set mounted with EFI system, the controller parameters were tuned and optimized empirically by hardware in loop and bench test methods. Test results show that the speed deviation of generator set is low and the control system is stable in steady state; In transient state the control system responses quickly, has high stability under mutation loads especially when suddenly apply and remove 100% load, the speed deviation is within 8% of reference speed and the transient time is less than 5 s, satisfying the ISO standard.

Torque Distribution Strategy for Integrated Starter/ Generator Hybrid Bus Implemented by Fuzzy Algorithm

A torque distribution strategy was designed by using fuzzy logic to realize the optimal control. The vehicle load zones were dynamically divided into several zones by several torque lines to indicate the drivers demand and the high or low efficient operating areas of the diesel engine. The fuzzy logic controller with trapezoid membership function and Mamdani rule reference mechanism was utilized. There are over 100 rules used in this fuzzy-based torque distribution strategy which are sorted into four rule-bases. The fuel economy and acceleration tests were designed to test and validate the integrated starter/generator (ISG) bus perfor-mance using fuzzy-based torque distribution strategy. The fuel economy is improved 7.7% compared with the rule-based strategy. Finally the road test results reveal that there is about 15% improvement of fuel economy. And the 0-50 km/h acceleration time is 9.5% shorter than the original bus.

Characteristics of permanent magnet linear synchronous motor fed by spwm inverter based on field-circuit coupled method

Presented field-circuit coupled adaptive time-stepping finite element method to study on permanent magnet linear synchronous motor (PMLSM) characteristics fed by SPWM voltage source inverter.In air-gap field where the direction or magnitude of the field is changing rapidly,the smallest elements are demanded due to high accuracy to use adaptive meshing technique.The co-simulation was used with the status space functions and time-step finite element functions,in which time-step of the status space functions was the smallest than finite element functions'.The magnitude relation of the normal elec- tromagnetic force and tangential electromagnetic force and the period were attained,and current curve was very abrupt at current zero area due to the bigger resistance and leak- age reactance,including main characteristics of motor voltage and velocity.The simulation results compare triumphantly with the experiments results.

Study on dynamics of central pattern generator for a quadrupedal robot

Based on Matsuoka＇s central pattern generator （CPG） model and taking quadruped as an example, the dynamics of CPG model was investigated through the single-parameter-analysis method and the numerical simulation technique. Simulation results indicate that the CPG model exhibits complex dynamics, while each parameter has specifically definitive influence trends on the CPG output. These conclusions were applied to control a quadrupedal robot to walk in different gaits, clear obstacle, and walk up- and down-slope successfully.

Design of intelligent detecting system based on wireless transmission

An intelligent detecting system based on wireless transmission is designed. Its hardware includes the card reading module, the wireless digital transmission module, the LCD module, the random password keyboard module and a 16×16 lattice word database based on e-Flash MM36SB020. Its software is a communication protocol between the central control computer and the entrance management base station. To resolve the conflicting problems occurred during the data transmission, a method of delaying time at random is proposed.

Tris(8-Hydroxyquinoline) Aluminum/2-(4-Biphenylyl)-5-(4-Tertbutylphenyl)-1,3,3-Oxadiazole Organic Multiple Quantum Wells for Electroluminescent Devices

Organic multiple quantum wells(OMQWs) consisting of alternating layers of organic materials have been fabricated from tris(8-hydroxyquinoline) aluminum(Alq)and 2-(4-biphenylyl)-5-(4-tertbutylphenyl)-1,3,3-oxadiazole(PBD) by a multisource-type high-vacuum organic molecular deposition.From the small-angle X-ray diffraction patterns of Alq/PBD OMQWs,a periodically layered structure is confirmed through the entire stack.The Alq layer thickness in the OMQWs was varied from 1 nm to 4 nm.From the optical absorption,photoluminescence and electroluminescence measurements,it is found that the exciton energy shifts to higher energy with decreasing Alq layer thickness,The changes of the exciton energy could be interpreted as the confinement effects of exciton in the Alq thin layers.Narrowing of the emission spectrum has also been observed for the electroluminescent devices (ELDs) with the OMQWs structure at room temperature.

Passive Matrix Organic Electroluminescent Display for 3G Cellular Phone

The major features of the display technologies for 3G cellular phone are reviewed. The comparison between their potential candidates for 3G cellular phone is given, and a detailed discussion is made on passive matrix organic electroluminescent display technology. A novel method to improve display contrast ratio is presented. Finally several 3G phone set prototypes with OLED display panels are given as well as the market forecast.

A discrete PI fault observer design and application in variable speed wind turbine system

For the discrete-time system which is subjected to uncoupled actuator faults and sensor faults simultaneously,a robust fault diagnosis method based on a proportional integral observer (PIO) is presented.The proposed PIO uses an additionally introduced integral term of the output errors to obtain the estimationof actuator faults. Besides, the sensor faults are regarded as the augment states so that the PIO cantrace them. Moreover, the convergence of the PIO is proved. A variable speed wind turbine(VWT) exampleis given to demonstrate the fast convergence and diagnosis precision of the proposed PIO.

Research of variable speed directly driven SRG wind power system position sensorless based on DFNN by FEA

A new method of switched reluctance wind power generation position sensorless based on DFNN by FEA was proposed, Through current and magnetic linkage to get the angle of SRG rotor position, the nonlinear mapping of cur- rent-magnetic linkage-angle was built, By training these sample data from FEA, the angle of SRG rotor position was replaced by the output of DFNN to achieve SRG position sensorless. Simulation results show that the error between actual rotor position and estimate rotor position is small; SRG can commutate with great accuracy; and the output voltage of SRG wind power system under variable wind speed is essentially constant.

Self-powered systems by nanogenerators and smart MEMS by piezotronics

Developing wireless nanodevices and nanosystems is of critical importance for sensing, medical science, environmental/infrastructure monitoring, defense technology and even personal electronics. It is highly desirable for wireless devices to be self-powered without using battery, without which most of the sensor network may be impossible. The pie- zoelectric nanogenerators have the potential to serve as self-sufficient power sources for micro/nano systems. For wurtzite structures that have non-central symmetry, such as ZnO, GaN and InN, a piezoelectric potential （piezopotential） is created in the crystal by applying a strain. The nanogenerator is invented by using the piezopotential as the driving force for electrons to flow in respond to a dynamic straining of piezoelectric nanowires. A gentle straining can produce an output voltage of up to 20 - 50 V from an integrated nanogenerator. Furthermore, piezopotential in the wurtzite structure can serve as gate voltage that can effectively tune/control the charge transport across an interface/junction; electronics fabricated based on such a mechanism is coined as piezotronics, with applications in force/pressure triggercd/controlled electronic devices, sensors, logic units and memory. By using the piezotronic effect, it is showed that the optoelectronic devices fabricated using wurtzite materials can have superior performance as solar cell, photon detector and light emitting diode. Piezotronie is likely to serve as ＂mechanosensation＂ for directly interfacing biomechanieal action with silicon based technology and active flexible electronics. The paper gives a brief review about the basis of nanogenertors and piezotronics and their potential applications in smart MEMS （micro-electro-mechanical systems）.