基于5630 TOP LED亚毫米级阵列式微型透镜的光学仿真

使用新型透镜提高LED取光效率是LED封装的研究热点之一。以亚毫米级阵列式微型透镜封装5630TOP LED为研究对象,利用光学仿真软件TracePro,考察了不同尺寸的阵列式圆锥透镜、半椭球透镜和半圆球透镜对LED取光效率的影响。仿真实验结果表明在优化条件下,5630TOP LED的取光效率可提高10.7%,光分布均匀。该仿真结果对下一步亚毫米级阵列式透镜的设计与制造有实际指导意义。

阵列式微型透镜封装多芯片COB LED的光学仿真设计及应用

为了提高COB LED的取光率,以1919COB LED为研究对象,建立阵列式圆锥透镜、半椭球透镜、四棱锥透镜和半圆球透镜封装LED模型,并利用光学仿真软件进行研究。仿真实验结果表明:在优化条件下,高0.5mm、直径0.9mm的阵列圆锥透镜封装LED的光通量由平面封装的67lm提高至84.3lm,即取光率提高25.8%。制作了RGB芯片的多芯片LED样品,并用直径1mm的阵列半圆球透镜进行封装,其取光率提高18.8%。

多芯片集成封装发光二极管的设计和优化

针对影响多芯片集成封装发光二极管(LED)出光效率的关键要素:图形化基板的反光杯间距、封装硅胶形状,利用光学仿真软件Tracepro优化设计了基板图形和封装硅胶的微观结构。通过改变反光杯之间的距离和封装硅胶的凹凸结构,获得最优的结构参数。计算结构表明,反光杯间距、封装硅胶结构对多芯片集成封装LED取光效率的影响具有一定的规律性,这些规律对于多芯片集成LED的封装具有一定的指导意义。

Sub-pixel extraction of laser stripeand itsapplication in laser plane calibration

For calibrating the laser plane to implement 3D shape measurement, an algorithm for extracting the laser stripe with sub-pixel accuracy is proposed. The proposed algorithm mainly consists of two stages： two-side edge detection and center line extraction. First, the two-side edge of laser stripe is detected using the principal component angle-based progressive probabilistic Hough transform and its width is calculated through the distance between these two edges. Secondly, the center line of laser strip is extracted with 2D Taylor expansion at a sub-pixel level and the laser plane is calibrated with the 3D reconstructed coordinates from the extracted 2D sub-pixel ones. Experimental results demonstrate that the proposed method can not only extract the laser stripe at a high speed, nearly average 78 ms/frame, but also calibrate the coplanar laser stripes at a low error, limited to 0.3 mm. The proposed algorithm can satisfy the system requirement of two-side edge detection and center line extraction, and rapid speed, high precision, as well as strong anti-jamming.

Efficiency Improvement of 590 nm AIGalnP Light Emitting Diode with a Reflective Top Electrode

In this work, enhancement of the light extraction efficiency of a 590 nm AIGaInP light-emitting diodes （LED） with a reflective top electrode （RTE） was investigated. A distributed Bragg reflector （DBR）, consisting of AIAs/AIGaAs pairs, grown on an AlGaInP structure was used as a reflector for a reflective top electrode. It was found that a higher output power was observed from the AIGalnP LED with a RTE than from a conventional one. In addition, it was noted that the improvement in the output power depends strongly on the reflectivity of the reflector and that it exhibits a more effective performance with low injection currents. The increase in the optical output power was attributed to the enhanced extraction efficiency caused by a reduction of light absorbed from the emission region to top electrode through the RTE.

Comparison between sequential and single extraction procedures for metal speciation in fresh and dried Sedum Plumbizincicola

Sequential and single extraction procedures were applied to both fresh and dried Sedum Plumbizincicola leaves and stems.The extractants, different from those of soil, sediment or sewage sludge metal fractions, were water, 80%(v/v) ethanol, 1 mol/L Na Cl,2% HAc and 0.6 mol/L HCl. Zn, Cd and Cu in the extracts and samples were measured by flame atomic adsorption spectrometry. In sequential extraction procedures, water soluble form and ethanol soluble form are the main fractions for Zn, while water soluble form and Na Cl soluble form for Cd, and comparatively uniform distribution for Cu with the residue form most and HCl soluble form second. Single extraction procedures are used to compare the extraction efficiencies of the five reagents to screen appropriate extractants and operating conditions for liquid extraction to deal with large amount of harvested metal-contained biomass, which will pose a threat to the environment if treated improperly. The sequences of extraction efficiencies are HCl>Na Cl≈HAc>Water≈Ethanol for Zn and HCl≈Na Cl≈HAc>Water>Ethanol for Cd. As for Cu, all the five extractants cannot effectively extract Cu, but HCl achieves a higher efficiency(>70% in fresh samples, and 45%-60% in dried samples). Besides, extraction efficiencies for most extractants in fresh samples are higher than those in dried samples, and extraction efficiencies of stems and leaves for the five extractants are close. The two extraction procedures can obtain high degree of accuracy with the relative standard deviation(RSD)lower than 10%, and metal recoveries are controlled between 80%-120% with most of 90%-110%.

Mechanism of Bragg Diffraction-Assisted Light Extraction in GaN-based Light-Emitting Diodes Based on a Self-Consistent Model

By introducing the distribution of the light energy density in GaN-based light-emitting diode (LED),theLED model based on the incoherent regime and the light extraction efficiency are investigated.The energy density asa function of the angle of incidence is calculated to demonstrate the mechanism of the light extraction.The deviationbetween the tendencies of the transmissivity of the output layer and the extraction efficiency is also demonstrated.

Physics of Power Semiconductor Streamer Laser

It is considered the mechanism of streamer discharge in the wide-gap semiconductors as a highly effective method of the laser excitation on the basis of representation about the phenomenon of light self-trapping of the discharge, providing their high propagation velocity down to v- 5 ×10^9 sm/s, the crystallographic orientation, filamentary character at thickness of the channel about 1 μm and absence of destructions of a crystal.

The Effect of Chlorine Dioxide Charges in Chlorine Dioxide-Alkaline Extraction-Chlorine Dioxide （DED） Sequence on Optical Properties of Kraft Pulp of Eucalyptus camaldulensis

Hardwoods are important raw material for making pulp and paper products. Eucalyptus camaldulensis is a fast-growing hardwood species with a wide distribution in Iran and can be introduced as appropriatematerial to compensate the wood shortages of the natural forest. Kraft pulping was performed under different cooking conditions and, based on the relations of pulp yield and kappa number, bleachable kraft pulp at screened yield of 43.3% and kappa number of 31.3 was selected for DED （Chlorine Dioxide-Alkaline Extraction-Chlorine Dioxide） bleaching and its bleachability was studied at different kappa factor in D~ stage. The results indicated that the bleachable kraft pulp from this species has high kappa number at acceptable screened yield and to complete the delignification in the bleaching process, higher kappa factor may be needed in DED bleaching sequence. The main reduction in final kappa number and yield loss were observed at kappa factor level of 0.2 but by further increase in kappa factor up to 0.4, more development were observed in optical properties but at lower opacity.

Extraction efficiency enhancement of LEDs using 2-D photonic crystal

Using photonic crystals (PCs), the extraction efficiency of the light-emitting diodes (LEDs) can be greatly enhanced by the effects of photonic band gap (PBG) and grating diffraction. The two theoretical methods are also discussed. Meanwhile, we demonstrate that LEDs can achieve high extraction efficiency by employing photonic crystal as diffraction grating. PCs with square lattice of cylindrical unit cells are fabricated in GaN layer of GaN-based blue LED. We present a theoretical discussion on the extraction efficiency of PC-LED, which relies on the effective medium theory and transmission matrix method to investigate the effect of lattice constant. The results show that the extraction efficiency of the high performance LEDs can achieve 61.8% when the lattice constant is 270 nm.

Rational design of perfectly oriented thermally activated delayed fluorescence emitter for efficient red electroluminescence

How to control the dipole orientation of organic emitters is a challenge in the field of organic light-emitting diodes(OLEDs).Herein,a linear thermally activated delayed fluorescence(TADF)molecule,PhNAI-PMSBA,bearing a 1,8-naphthalimide-acridine framework was designed by a doublesite long-axis extension strategy to actively control the dipole orientation.The horizontal ratio of emitting dipole orientation of PhNAI-PMSBA reaches 95%,substantially higher than that of isotropic emitters(67%).This unique feature is associated with the intrinsically horizontal molecular orientation of PhNAI-PMSBA and the good agreement between its transition dipole moment direction and molecular long axis.The PhNAI-PMSBA-based OLED achieves an ultrahigh optical outcoupling efficiency of 43.2%and thus affords one of the highest red electroluminescence with an external quantum efficiency of 22.3%and the Commission International de l’Eclairage 1931 coordinates at around(0.60,0.40).

Influence of the replacement of alkoxyl with alkylthienyl on photovoltaic properties of two small molecule donors for organic solar cells

Two benzo[1,2-b:4,5-b￠]dithiophene(BDT)-based small molecule(SM) donor materials with identical conjugated backbones but different substitution groups, named as DRTB-O and DRTB-T, were well explored to demonstrate the influence of the replacement of alkoxy with alkylthienyl on their photovoltaic properties in fullerene-based and fullerene-free organic solar cells(OSCs). The study shows that the two SM donors possess similar absorption spectra and energy levels but different crystalline structures in solid films. The carrier transport property and phase separation morphologies of the blend films have also been fully investigated.By employing PC71 BM as the acceptor, the power conversion efficiency(PCE) of DRTB-O:PC71BM and DRTB-T:PC71BM based devices were 4.91% and 7.08%, respectively. However, by blending with IDIC, the two SM donors exhibited distinctly different photovoltaic properties in fullerene-free OSCs, and the PCE of DRTB-O:IDIC and DRTB-T:IDIC based devices were 0.15% and9.06%, respectively. These results indicate that the replacement of alkoxyl with alkylthienyl in designing SM donor materials plays an important role in the application of fullerene-free OSCs.