Theα＋βtitanium alloy, Ti-6Al-4V, was welded by friction stir welding using a W-Re pin tool, and the defect-free weld was produced with proper welding parameters. Texture of the Ti-6Al-4V friction stir weld was stud...Theα＋βtitanium alloy, Ti-6Al-4V, was welded by friction stir welding using a W-Re pin tool, and the defect-free weld was produced with proper welding parameters. Texture of the Ti-6Al-4V friction stir weld was studied by orientation imaging microscopy. The as-received Ti-6Al-4V sheet mill annealed was composed of elongated primary α and transformed β. A typical rolling texture was observed in the base material. The microstructure of the stir zone was significantly different from that of the base material. The stir zone was characterized by the presence of considerable amount of equiaxed dynamically recrystallized grains and a texture around{Ф1=30°,φ=62°,Ф2=30°}was developed during the friction stir welding.展开更多
The amplitude-dependent and temperature-dependent low frequency damping capacities of magnesium with 99.96% purity were studied by a dynamic mechanical analyzer. The pure magnesium alloys include CPM1 and CPM2 casting...The amplitude-dependent and temperature-dependent low frequency damping capacities of magnesium with 99.96% purity were studied by a dynamic mechanical analyzer. The pure magnesium alloys include CPM1 and CPM2 castings having textures of columnar grains which extraordinarily influence the damping behaviours. The commercial pure magnesium alloy CPM was re-melted to obtain equiaxed grains, which could remove the effect of texture orientation on the damping behaviours of these pure magnesium alloys. The results of strain amplitude-dependent damping spectrums of these pure magnesium alloys show that the pure magnesium with equiaxed grains possesses the highest damping capacity. In temperature-dependent damping plot for all these three pure magnesium alloys, there are two damping peaks P1 and P2 located at 80 and 230 °C, respectively. These two damping peaks are considered to be caused by the interaction between dislocation and point defects, and the movement of grain boundaries, respectively.展开更多
基金financial supports from the National Natural Science Foundation of China(Nos.U1764253,51971044,U1910213,52001037,U2037601)the Qinghai Scientific&Technological Program,China(No.2018-GX-A1)the Natural Science Foundation of Chongqing,China(No.cstc2019jcyjmsxm X0234)。
基金Project(2010CB731704)supported by the National Basic Research Program of ChinaProject(AWJ-M13-11)supported by State Key Laboratory of Advanced Welding and Joining,Harbin Institute of Technology,ChinaProject(2012M511470)supported by China Postdoctoral Science Foundation
文摘Theα＋βtitanium alloy, Ti-6Al-4V, was welded by friction stir welding using a W-Re pin tool, and the defect-free weld was produced with proper welding parameters. Texture of the Ti-6Al-4V friction stir weld was studied by orientation imaging microscopy. The as-received Ti-6Al-4V sheet mill annealed was composed of elongated primary α and transformed β. A typical rolling texture was observed in the base material. The microstructure of the stir zone was significantly different from that of the base material. The stir zone was characterized by the presence of considerable amount of equiaxed dynamically recrystallized grains and a texture around{Ф1=30°,φ=62°,Ф2=30°}was developed during the friction stir welding.
基金Project (50801017) supported by the National Natural Science Foundation of Chinaproject (20080440843) supported by Postdoctoral Science Foundation, ChinaProject (HIT.NSRIF.2009028) supported by the Natural Scientific Research Innovation Foundation of Harbin Institute of Technology, China
文摘The amplitude-dependent and temperature-dependent low frequency damping capacities of magnesium with 99.96% purity were studied by a dynamic mechanical analyzer. The pure magnesium alloys include CPM1 and CPM2 castings having textures of columnar grains which extraordinarily influence the damping behaviours. The commercial pure magnesium alloy CPM was re-melted to obtain equiaxed grains, which could remove the effect of texture orientation on the damping behaviours of these pure magnesium alloys. The results of strain amplitude-dependent damping spectrums of these pure magnesium alloys show that the pure magnesium with equiaxed grains possesses the highest damping capacity. In temperature-dependent damping plot for all these three pure magnesium alloys, there are two damping peaks P1 and P2 located at 80 and 230 °C, respectively. These two damping peaks are considered to be caused by the interaction between dislocation and point defects, and the movement of grain boundaries, respectively.
