According to the different engineering mechanical states of top coal caving andnormal stoping of gaseous loose thick coal seams,the dialectical relation between thiscaving method and dynamic disasters was analyzed by ...According to the different engineering mechanical states of top coal caving andnormal stoping of gaseous loose thick coal seams,the dialectical relation between thiscaving method and dynamic disasters was analyzed by simulating the change of stressstates in the process of top coal initial caving with different mining and caving ratios basedon the ANSYS10.0.The variation of elastic energy and methane expansion energy duringfirst top coal caving was analyzed by first weighting and periodic weighting and combiningwith coal stress and deformation distribution of top coal normal stoping as well as positiveand negative examples in top coal caving of outburst coal seam.The research shows thatthe outburst risk increases along with the increase of the caving ratio in the initial miningstage.In the period of normal stoping,when the mining and caving ratio is smaller than1:3 and hard and massive overlying strata do not exist (periodic weighting is not obvious),it is beneficial to control ground stress leading type outburst.Thus,it is unreasonable toprohibit top coal caving in dangerous and outburst prone areas.展开更多
A two-dimensional(2-D) finite element(FE) model was developed to analyze the deformation and stress of embankment on soft ground due to widening with different treatment techniques.It is found that the embankment wide...A two-dimensional(2-D) finite element(FE) model was developed to analyze the deformation and stress of embankment on soft ground due to widening with different treatment techniques.It is found that the embankment widening induces transverse gradient change due to differential settlements and horizontal outward movements at the shoulder of the existing embankment.Embankment widening also increases the shear stress along the slope of the existing embankment,especially at the foot of slope.The failure potential due to embankment widening may increase with the increase of widening width when the widening width is smaller than 8.5 m,but may decrease with the increase of widening width as the widening width is greater than 8.5 m.The effectiveness of four ground and embankment treatment techniques,including geosynthetic reinforcement,light-weight embankment,deep mixed columns,and separating wall were compared.The results indicate that these treatments reduce the differential settlements and improve the stability.The light-weight embankment has the most effectiveness among four treatments.By using the fly-ash backfill material in widening,the transverse gradient change decreases from 0.5%-1.3% to 0.26%-0.8% and the maximum horizontal displacement decreases from 2.76 cm to 1.44 cm.展开更多
The laboratory tests on the post-liquefaction deformation of saturated sand-gravel composites were performed to investigate the characteristics of stress-strain relation and the dissipation of pore water pressure by t...The laboratory tests on the post-liquefaction deformation of saturated sand-gravel composites were performed to investigate the characteristics of stress-strain relation and the dissipation of pore water pressure by the hollow cylinder apparatus. It is found that the stress-strain response and the dissipation process of pore water pressure are composed of three stages, including the low intensive strength stage, the superlinear strength recovery stage and the sublinear strength recovery stage, and the demarcation points of the curve of pore water pressure are lag behind those of the stress-strain response. The comparison results of the behaviour of large post-liquefaction deformation between saturated sand-gravel composites and Nanjing fine sand show that the low intensive strength stage and the superlinear strength recovery stage of saturated sand-gravel composites are shorter while the sublinear strength recovery stage is longer. A stress-strain model and a dissipation model of excess pore water pressure of liquefied sand-gravel composites are established, in which the initial confining pressure and the relative density can be considered synthetically. And it is found that the predicted results by the two models are in good agreement with experimental data.展开更多
Submerged arc welding （SAW） is advantageous for joining high thickness materials in large structure due to high material deposition rate. The non-uniform heating and cooling generates the thermal stresses and subseq...Submerged arc welding （SAW） is advantageous for joining high thickness materials in large structure due to high material deposition rate. The non-uniform heating and cooling generates the thermal stresses and subsequently the residual stresses and distortion. The longitudinal and transverse residual stresses and angular distortion are generally measured in large panel structure of submerged arc welded fillet joints. Hence, the objective of this present work is to quantify the amount of residual stress and distortion in and around the weld joint due to positioning of stiffeners tack. The tacking sequence influences the level of residual stress and proper controlling of tacking sequences is required to minimize the stress. In present study, an elasto-plastic material behavior is considered to develop the thermo mechanical model which predicts the residual stress and angular distortion with varying tacking sequences. The simulated result reveals that the tacking sequence heavily influences the residual stress and deformation pattern of the single sided fillet joint. The finite element based numerical model is calibrated by comparing the experimental data from published literature. Henceforth, the angular distortions are measured from an in-house developed experimental set-up. A fair agreement between the predicted and experimental results indicates the robustness of the developed numerical model. However, the most significant conclusion from present study states that tack weld position should be placed opposite to the fillet weld side to minimize the residual stress.展开更多
基金Project supported by the National Natural Science Foundation of China (Nos. 10772104 and 10872045)the Innovation Project of Shanghai Municipal Education Commission (No. 09YZ12)the Shanghai Leading Academic Discipline Project (No. S30106)
文摘According to the different engineering mechanical states of top coal caving andnormal stoping of gaseous loose thick coal seams,the dialectical relation between thiscaving method and dynamic disasters was analyzed by simulating the change of stressstates in the process of top coal initial caving with different mining and caving ratios basedon the ANSYS10.0.The variation of elastic energy and methane expansion energy duringfirst top coal caving was analyzed by first weighting and periodic weighting and combiningwith coal stress and deformation distribution of top coal normal stoping as well as positiveand negative examples in top coal caving of outburst coal seam.The research shows thatthe outburst risk increases along with the increase of the caving ratio in the initial miningstage.In the period of normal stoping,when the mining and caving ratio is smaller than1:3 and hard and massive overlying strata do not exist (periodic weighting is not obvious),it is beneficial to control ground stress leading type outburst.Thus,it is unreasonable toprohibit top coal caving in dangerous and outburst prone areas.
文摘A two-dimensional(2-D) finite element(FE) model was developed to analyze the deformation and stress of embankment on soft ground due to widening with different treatment techniques.It is found that the embankment widening induces transverse gradient change due to differential settlements and horizontal outward movements at the shoulder of the existing embankment.Embankment widening also increases the shear stress along the slope of the existing embankment,especially at the foot of slope.The failure potential due to embankment widening may increase with the increase of widening width when the widening width is smaller than 8.5 m,but may decrease with the increase of widening width as the widening width is greater than 8.5 m.The effectiveness of four ground and embankment treatment techniques,including geosynthetic reinforcement,light-weight embankment,deep mixed columns,and separating wall were compared.The results indicate that these treatments reduce the differential settlements and improve the stability.The light-weight embankment has the most effectiveness among four treatments.By using the fly-ash backfill material in widening,the transverse gradient change decreases from 0.5%-1.3% to 0.26%-0.8% and the maximum horizontal displacement decreases from 2.76 cm to 1.44 cm.
基金Project(90715018)supported by the National Natural Science Foundation of ChinaProject(200808022)supported by the Special Fund for the Commonweal Indusry of China+1 种基金Project(08KJA560001)supported by the Key Basic Research Program of Natural Science of University in Jiangsu ProvinceProject(CX10B_170Z)supported by the Postgraduate Scientific Innovation Program in Jiangsu Province,China
文摘The laboratory tests on the post-liquefaction deformation of saturated sand-gravel composites were performed to investigate the characteristics of stress-strain relation and the dissipation of pore water pressure by the hollow cylinder apparatus. It is found that the stress-strain response and the dissipation process of pore water pressure are composed of three stages, including the low intensive strength stage, the superlinear strength recovery stage and the sublinear strength recovery stage, and the demarcation points of the curve of pore water pressure are lag behind those of the stress-strain response. The comparison results of the behaviour of large post-liquefaction deformation between saturated sand-gravel composites and Nanjing fine sand show that the low intensive strength stage and the superlinear strength recovery stage of saturated sand-gravel composites are shorter while the sublinear strength recovery stage is longer. A stress-strain model and a dissipation model of excess pore water pressure of liquefied sand-gravel composites are established, in which the initial confining pressure and the relative density can be considered synthetically. And it is found that the predicted results by the two models are in good agreement with experimental data.
基金Supported by the Indian Institute of Technology Guwahati under Grant No:SG/ME/PB/P/01
文摘Submerged arc welding （SAW） is advantageous for joining high thickness materials in large structure due to high material deposition rate. The non-uniform heating and cooling generates the thermal stresses and subsequently the residual stresses and distortion. The longitudinal and transverse residual stresses and angular distortion are generally measured in large panel structure of submerged arc welded fillet joints. Hence, the objective of this present work is to quantify the amount of residual stress and distortion in and around the weld joint due to positioning of stiffeners tack. The tacking sequence influences the level of residual stress and proper controlling of tacking sequences is required to minimize the stress. In present study, an elasto-plastic material behavior is considered to develop the thermo mechanical model which predicts the residual stress and angular distortion with varying tacking sequences. The simulated result reveals that the tacking sequence heavily influences the residual stress and deformation pattern of the single sided fillet joint. The finite element based numerical model is calibrated by comparing the experimental data from published literature. Henceforth, the angular distortions are measured from an in-house developed experimental set-up. A fair agreement between the predicted and experimental results indicates the robustness of the developed numerical model. However, the most significant conclusion from present study states that tack weld position should be placed opposite to the fillet weld side to minimize the residual stress.
