A crystal plasticity finite element model was developed for the drawing deformation of pure copper micro wire,based on rate-dependent crystal plasticity theory.The impact of wire diameter compression ratio on the micr...A crystal plasticity finite element model was developed for the drawing deformation of pure copper micro wire,based on rate-dependent crystal plasticity theory.The impact of wire diameter compression ratio on the micro-mechanical deformation behavior during the wire drawing process was investigated.Results indicate that the internal deformation and slip of the drawn wire are unevenly distributed,forming distinct slip and non-slip zones.Additionally,horizontal strain concentration bands develop within the drawn wire.As the wire diameter compression ratio increases,the strength of the slip systems and the extent of slip zones inside the deformation zone also increase.However,the fluctuating stress state,induced by contact pressure and frictional stress,results in a rough and uneven wire surface and diminishes the stability of the drawing process.展开更多
The overbroken rock mass of gob areas is made up of broken and accumulated rock blocks compressed to some extent by the overlying strata. The beating pressure of the gob can directly affect the safety of mining fields...The overbroken rock mass of gob areas is made up of broken and accumulated rock blocks compressed to some extent by the overlying strata. The beating pressure of the gob can directly affect the safety of mining fields, formarion of road retained along the next goaf and seepage of water and methane through the gob. In this paper, the software RFPA＇2000 is used to construct numerical models. Especially the Euler method of control volume is proposed to solve the simulation difficulty arising from plastically finite deformations. The results show that three characteristic regions occurred in the gob area： （1） a naturally accumulated region, 0-10 m away from unbroken surrounding rock walls, where the beating pressure is nearly zero; （2） an overcompacted region, 10-20 m away from unbroken walls, where the beating pressure results in the maximum value of the gob area; （3） a stable compaction region, more than 20 m away from unbroken walls and occupying absolutely most of the gob area, where the beating pressures show basically no differences. Such a characteristic can exolain the easy-seeoaged “O”-ring phenomena around mining fields very well.展开更多
The use of a constrained groove pressing(CGP) method to plastically deform AA6063 aluminum alloy led to the improved surface properties. It was found that hardness magnitude is dramatically improved and its uniformity...The use of a constrained groove pressing(CGP) method to plastically deform AA6063 aluminum alloy led to the improved surface properties. It was found that hardness magnitude is dramatically improved and its uniformity is considerably decreased after the first pass, while subsequent passes result in better hardness behavior for the processed material. Also, the elongated grains formed in the first pass of the CGP are gradually converted to the equiaxed counterparts by adding pass numbers. Eventually, higher corrosion resistance of the sample by imposing the CGP process is related to the quick formation of passivation film and the change in the morphology of the second phase and precipitates which hinder their electrochemical reactions and decrease the potential localized attack sites.展开更多
基金the National Natural Science Foundation of China(Nos.U21A2051,52173297,52071133)the R&D Projects of Henan Academy of Sciences of China(No.220910009)+2 种基金the Key R&D and Promotion Projects of Henan Province of China(No.212102210441)the Joint Fund of Henan Science and Technology R&D Plan of China(No.222103810037)the Zhongyuan Scholar Workstation Funded Project of China(No.214400510028).
文摘A crystal plasticity finite element model was developed for the drawing deformation of pure copper micro wire,based on rate-dependent crystal plasticity theory.The impact of wire diameter compression ratio on the micro-mechanical deformation behavior during the wire drawing process was investigated.Results indicate that the internal deformation and slip of the drawn wire are unevenly distributed,forming distinct slip and non-slip zones.Additionally,horizontal strain concentration bands develop within the drawn wire.As the wire diameter compression ratio increases,the strength of the slip systems and the extent of slip zones inside the deformation zone also increase.However,the fluctuating stress state,induced by contact pressure and frictional stress,results in a rough and uneven wire surface and diminishes the stability of the drawing process.
基金Projects 2005CB221502 supported by the Vital Foundational 973 Program of China, 50225414 by the National Outstanding Youth Foundation,20040350222 by China Postdoctoral Science FoundationBK 2004033 by Jiangsu Natural Science Foundation
文摘The overbroken rock mass of gob areas is made up of broken and accumulated rock blocks compressed to some extent by the overlying strata. The beating pressure of the gob can directly affect the safety of mining fields, formarion of road retained along the next goaf and seepage of water and methane through the gob. In this paper, the software RFPA＇2000 is used to construct numerical models. Especially the Euler method of control volume is proposed to solve the simulation difficulty arising from plastically finite deformations. The results show that three characteristic regions occurred in the gob area： （1） a naturally accumulated region, 0-10 m away from unbroken surrounding rock walls, where the beating pressure is nearly zero; （2） an overcompacted region, 10-20 m away from unbroken walls, where the beating pressure results in the maximum value of the gob area; （3） a stable compaction region, more than 20 m away from unbroken walls and occupying absolutely most of the gob area, where the beating pressures show basically no differences. Such a characteristic can exolain the easy-seeoaged “O”-ring phenomena around mining fields very well.
基金funded by“Quality Engineering Project of Anhui Province of China in 2016”entitled mold design and manufacturing experimental training center(2016sxzx050)。
文摘The use of a constrained groove pressing(CGP) method to plastically deform AA6063 aluminum alloy led to the improved surface properties. It was found that hardness magnitude is dramatically improved and its uniformity is considerably decreased after the first pass, while subsequent passes result in better hardness behavior for the processed material. Also, the elongated grains formed in the first pass of the CGP are gradually converted to the equiaxed counterparts by adding pass numbers. Eventually, higher corrosion resistance of the sample by imposing the CGP process is related to the quick formation of passivation film and the change in the morphology of the second phase and precipitates which hinder their electrochemical reactions and decrease the potential localized attack sites.
