The study of flame development characteristics is crucial in the study of flame propagation, extinction, and for the investigation of combustion cyclic variability in SI engine. The aim of this study is to investigate...The study of flame development characteristics is crucial in the study of flame propagation, extinction, and for the investigation of combustion cyclic variability in SI engine. The aim of this study is to investigate the characteristics of flame development in a lean-stratified combustion of Natural Gas Engine （CNG） in a single cylinder direct injection （DI） engine at a specific motor speed, and fixed injection timing and air-fuel ratio by varying only the swirl level at the intake. The engine was set to run at 1800 rpm with half-load throttled. The ignition advance was set at 21.5 BTDC, and to create an overall lean and stratified mixture, injection timing was set at 61 BTDC with an air-fuel-ratio of 40.5 （λ=2.35）. Variable turbulent flow conditions near spark-plug were created by positioning the swirl control valves （SCV） at the intake port just before the two intake valves. This was done by setting one of the valves at full open position and the other one at 0% closed, 50% closed and 100% closed positions in order to achieve medium tumble （no swirl）, medium swirl and high swirl flows in the cylinder, respectively. An endoscope and CCD camera assembly was utilized to capture the flame images from the tumble plane at the intake side of the engine ever）, 2 CA degrees after ignition timing （AIT） for 40 CAs. It was observed that flame growth rate and flame convection velocity are increasing with increasing the swirl level. The total combustion duration is, thus, shorter in swirl induced combustion than without. However, COV in IMEP is greater in swirl induced flow cases than the medium tumble.展开更多
Biogas fuel is a sustainable and renewable fuel produced from anaerobic digestion of organic matter. The biogas fuel is a flammable mixture of methane and carbon dioxide with low to medium calorific values. Biogas is ...Biogas fuel is a sustainable and renewable fuel produced from anaerobic digestion of organic matter. The biogas fuel is a flammable mixture of methane and carbon dioxide with low to medium calorific values. Biogas is an alternative to conventional fossil fuels and can be used for beating, transportation and power generation. CFD （computational fluid dynamic） analysis of the combustion performance and emissions of biogas fuel in gas turbine engines is presented in this study. The main objective of this study is to understand the impact of the variability in the biogas fuel compositions and lower heating values on the combustion process. Natural gas, biogas from anaerobic digester, landfill biogas, and natural gas/biogas mixture fuels combustion were investigated in this study. The CFD results show lower peak flame temperature and CO mole fractions inside the combustor and lower NOx emissions at the combustor exit for the biogas compared to natural gas fuel. The peak flame temperature decreases by 37% for the biogas landfill （COJCH4 = 0.89） and by 22% for the biogas anaerobic digester （CO2/CH4 = 0.54） compared to natural gas fuel combustion. The peak CO mole fraction inside the combustor decreases from 9.8 × 10-2 for natural gas fuel to 2.22 × 10-4 for biogas anaerobic digester and 1.32 × 10-7 for biogas landfill. The average NOx mole fraction at the combustor exit decreases from 1.13 × 10-5 for natural gas fuel to 0.40 × 10-6 for biogas anaerobic digester and 1.06 × 10-6 for biogas landfill. The presence of non-combustible constituents in the biogas reduces the temperature of the flame and consequently the NOx emissions.展开更多
文摘The study of flame development characteristics is crucial in the study of flame propagation, extinction, and for the investigation of combustion cyclic variability in SI engine. The aim of this study is to investigate the characteristics of flame development in a lean-stratified combustion of Natural Gas Engine （CNG） in a single cylinder direct injection （DI） engine at a specific motor speed, and fixed injection timing and air-fuel ratio by varying only the swirl level at the intake. The engine was set to run at 1800 rpm with half-load throttled. The ignition advance was set at 21.5 BTDC, and to create an overall lean and stratified mixture, injection timing was set at 61 BTDC with an air-fuel-ratio of 40.5 （λ=2.35）. Variable turbulent flow conditions near spark-plug were created by positioning the swirl control valves （SCV） at the intake port just before the two intake valves. This was done by setting one of the valves at full open position and the other one at 0% closed, 50% closed and 100% closed positions in order to achieve medium tumble （no swirl）, medium swirl and high swirl flows in the cylinder, respectively. An endoscope and CCD camera assembly was utilized to capture the flame images from the tumble plane at the intake side of the engine ever）, 2 CA degrees after ignition timing （AIT） for 40 CAs. It was observed that flame growth rate and flame convection velocity are increasing with increasing the swirl level. The total combustion duration is, thus, shorter in swirl induced combustion than without. However, COV in IMEP is greater in swirl induced flow cases than the medium tumble.
文摘Biogas fuel is a sustainable and renewable fuel produced from anaerobic digestion of organic matter. The biogas fuel is a flammable mixture of methane and carbon dioxide with low to medium calorific values. Biogas is an alternative to conventional fossil fuels and can be used for beating, transportation and power generation. CFD （computational fluid dynamic） analysis of the combustion performance and emissions of biogas fuel in gas turbine engines is presented in this study. The main objective of this study is to understand the impact of the variability in the biogas fuel compositions and lower heating values on the combustion process. Natural gas, biogas from anaerobic digester, landfill biogas, and natural gas/biogas mixture fuels combustion were investigated in this study. The CFD results show lower peak flame temperature and CO mole fractions inside the combustor and lower NOx emissions at the combustor exit for the biogas compared to natural gas fuel. The peak flame temperature decreases by 37% for the biogas landfill （COJCH4 = 0.89） and by 22% for the biogas anaerobic digester （CO2/CH4 = 0.54） compared to natural gas fuel combustion. The peak CO mole fraction inside the combustor decreases from 9.8 × 10-2 for natural gas fuel to 2.22 × 10-4 for biogas anaerobic digester and 1.32 × 10-7 for biogas landfill. The average NOx mole fraction at the combustor exit decreases from 1.13 × 10-5 for natural gas fuel to 0.40 × 10-6 for biogas anaerobic digester and 1.06 × 10-6 for biogas landfill. The presence of non-combustible constituents in the biogas reduces the temperature of the flame and consequently the NOx emissions.
