It is found that tensile flow curves of samples of annealed ultrafine-grained aluminum AA1090 show the development of a yield point and a significant mechanical anisotropy.To rationalize the anisotropic tensile behavi...It is found that tensile flow curves of samples of annealed ultrafine-grained aluminum AA1090 show the development of a yield point and a significant mechanical anisotropy.To rationalize the anisotropic tensile behavior,the orientation data of the annealed material were measured using electron backscatter microscopy.It is found that the inferior mechanical properties of samples tested at 45°to the rolling direction may be attributed to a strong rolling texture effect and that the anisotropic magnitude of the yield drop may be related to the proportion of grains with soft orientations(defined as those with Schmid factor greater than 0.45)in the sample.Additionally,it is found that the anisotropy in tensile ductility is in general agreement with a Considère criterion analysis and that the mechanical anisotropy in the samples is only partly explained by the crystallographic texture,where microstructural anisotropy may also play a role.展开更多
The equi-biaxial tensile test is often required for parameter identification of anisotropic yield function and it demands thespecial testing technique or device. Instead of the equi-biaxial tensile test, the plane str...The equi-biaxial tensile test is often required for parameter identification of anisotropic yield function and it demands thespecial testing technique or device. Instead of the equi-biaxial tensile test, the plane strain test carried out with the traditional uniaxialtesting machine is suggested to provide the experimental data for calibration of anisotropic yield function. This simplified method byusing plane strain test was adopted to identify the parameters of Yld2000-2d yield function for 5xxx aluminum alloy and AlMgSialloy sheets. The predicted results of yield stresses, anisotropic coefficients and yield loci by the proposed method were very similarwith the experimental data and those by the equi-biaxial tensile test. It is validated that the plane strain test is effective to provideexperimental data instead of equi-biaxial tensile test for calibration of Yld2000-2d yield function.展开更多
The effect of electropulsing treatment on microstructure and mechanical strength of laser metal deposited Ti−6Al−4V alloy was investigated in order to eliminate the anisotropy in strength of laser metal deposited Ti−6...The effect of electropulsing treatment on microstructure and mechanical strength of laser metal deposited Ti−6Al−4V alloy was investigated in order to eliminate the anisotropy in strength of laser metal deposited Ti−6Al−4V alloy by tensile tests,optical microscopy,scanning electron microscopy,electron back-scattered diffraction analyses and transmission electron microscopy.With increasing applied voltages from 0 to 130 V,the evolution of microstructure within columnarβgrains followed the sequence ofα′martensite→colonyαstructure→basket-weaveαstructure.The electropulsing treated at 130 V weakened the texture of martensite withinβgrains.The as-built Ti−6Al−4V alloy showed an anisotropy in yield strength(6.2%).After processing at 130 V,the anisotropy in yield strength was reduced to 0.6%,which was attributed to the almost equivalent distribution of Schmid factor in the samples deformed along different orientations.展开更多
This paper is devoted to developing a yield criterion that can model the asymmetry and anisotropy in yielding of pressure insensitive metals,in terms of accuracy and simplicity of formulation.First,a new isotropic yie...This paper is devoted to developing a yield criterion that can model the asymmetry and anisotropy in yielding of pressure insensitive metals,in terms of accuracy and simplicity of formulation.First,a new isotropic yield criterion,which can model the asymmetry in yielding of pressure insensitive metals,is proposed.Further,using Cazacu's generalizations to anisotropic conditions of the invariants of the deviatoric stress,the proposed isotropic yield criterion is extended to orthotropy.The proposed anisotropic criterion has a quite simple form,and the number of material constants involved is only half of that of Cazacu's(2004) yield criterion.Compared to Hill's(1948) yield criterion,the proposed anisotropic yield criterion has three additional constants,which are used to model the tension-compression asymmetry of materials.All the material constants involved in the criterion can be determined by simple tests.The proposed criterion reduces to Hill's(1948) yield criterion if the tensile and compressive yield stresses are equal.In other words,the proposed anisotropic yield criterion can be considered as an extension of Hill's(1948) criterion to tension-compression asymmetry materials.The anisotropic yield criterion is used to describe the plastic response of Cu-Al-Be shape memory alloy(data after Laydi and Lexcellent) and Ni3Al based intermetallic alloy IC10 sheets.It is shown that the proposed yield criterion can describe very well the asymmetry and anisotropy observed in those materials.展开更多
基金Project(50971074)supported by the National Natural Science Foundation of China
文摘It is found that tensile flow curves of samples of annealed ultrafine-grained aluminum AA1090 show the development of a yield point and a significant mechanical anisotropy.To rationalize the anisotropic tensile behavior,the orientation data of the annealed material were measured using electron backscatter microscopy.It is found that the inferior mechanical properties of samples tested at 45°to the rolling direction may be attributed to a strong rolling texture effect and that the anisotropic magnitude of the yield drop may be related to the proportion of grains with soft orientations(defined as those with Schmid factor greater than 0.45)in the sample.Additionally,it is found that the anisotropy in tensile ductility is in general agreement with a Considère criterion analysis and that the mechanical anisotropy in the samples is only partly explained by the crystallographic texture,where microstructural anisotropy may also play a role.
基金Project(P2018-013)supported by the Open Foundation of State Key Laboratory of Materials Processing and Die&Mould Technology,Huazhong University of Science and Technology,China
文摘The equi-biaxial tensile test is often required for parameter identification of anisotropic yield function and it demands thespecial testing technique or device. Instead of the equi-biaxial tensile test, the plane strain test carried out with the traditional uniaxialtesting machine is suggested to provide the experimental data for calibration of anisotropic yield function. This simplified method byusing plane strain test was adopted to identify the parameters of Yld2000-2d yield function for 5xxx aluminum alloy and AlMgSialloy sheets. The predicted results of yield stresses, anisotropic coefficients and yield loci by the proposed method were very similarwith the experimental data and those by the equi-biaxial tensile test. It is validated that the plane strain test is effective to provideexperimental data instead of equi-biaxial tensile test for calibration of Yld2000-2d yield function.
基金financial supports from the National Key R&D Program of China (No.2017YFE0123500)。
文摘The effect of electropulsing treatment on microstructure and mechanical strength of laser metal deposited Ti−6Al−4V alloy was investigated in order to eliminate the anisotropy in strength of laser metal deposited Ti−6Al−4V alloy by tensile tests,optical microscopy,scanning electron microscopy,electron back-scattered diffraction analyses and transmission electron microscopy.With increasing applied voltages from 0 to 130 V,the evolution of microstructure within columnarβgrains followed the sequence ofα′martensite→colonyαstructure→basket-weaveαstructure.The electropulsing treated at 130 V weakened the texture of martensite withinβgrains.The as-built Ti−6Al−4V alloy showed an anisotropy in yield strength(6.2%).After processing at 130 V,the anisotropy in yield strength was reduced to 0.6%,which was attributed to the almost equivalent distribution of Schmid factor in the samples deformed along different orientations.
文摘This paper is devoted to developing a yield criterion that can model the asymmetry and anisotropy in yielding of pressure insensitive metals,in terms of accuracy and simplicity of formulation.First,a new isotropic yield criterion,which can model the asymmetry in yielding of pressure insensitive metals,is proposed.Further,using Cazacu's generalizations to anisotropic conditions of the invariants of the deviatoric stress,the proposed isotropic yield criterion is extended to orthotropy.The proposed anisotropic criterion has a quite simple form,and the number of material constants involved is only half of that of Cazacu's(2004) yield criterion.Compared to Hill's(1948) yield criterion,the proposed anisotropic yield criterion has three additional constants,which are used to model the tension-compression asymmetry of materials.All the material constants involved in the criterion can be determined by simple tests.The proposed criterion reduces to Hill's(1948) yield criterion if the tensile and compressive yield stresses are equal.In other words,the proposed anisotropic yield criterion can be considered as an extension of Hill's(1948) criterion to tension-compression asymmetry materials.The anisotropic yield criterion is used to describe the plastic response of Cu-Al-Be shape memory alloy(data after Laydi and Lexcellent) and Ni3Al based intermetallic alloy IC10 sheets.It is shown that the proposed yield criterion can describe very well the asymmetry and anisotropy observed in those materials.
