Tight sandstone has a certain anisotropy. Using ultrasonic measurements of samples in three different directions and related matched experiments, this study systematically analyzes the pore structure and anisotropy of...Tight sandstone has a certain anisotropy. Using ultrasonic measurements of samples in three different directions and related matched experiments, this study systematically analyzes the pore structure and anisotropy of tight sandstone samples obtained from oil fields and compares results with those of shale. Results firstly show that the anisotropy of tight sandstone is mainly related to the compositional layering and thin interbedding which occur in different sedimentary environments. Tight sandstone has typical transverse isotropic medium characteristics, Young’s modulus increases in different directions with increasing confining pressure, Poisson’s ratio change is not obvious, anisotropic coefficients decrease with increasing effective pressure, and a certain linear relationship exists between ε, γ, and δ. This article finally summarizes anisotropy in different areas, thereby providing a foundation for the use of suitable appraisal models in different regions. This research can be used as an experimental reference for logging evaluation, seismic data interpretation, and fracturing develop of tight sandstones.展开更多
Transmission electron microscopy(TEM),electron backscattered diffraction imaging(EBSD)and X-ray diffractometry were used to analyze the microstructure and texture characteristics of Al-9.8Mg-1.5Li-0.4Mn alloy cross-ro...Transmission electron microscopy(TEM),electron backscattered diffraction imaging(EBSD)and X-ray diffractometry were used to analyze the microstructure and texture characteristics of Al-9.8Mg-1.5Li-0.4Mn alloy cross-rolled and extruded plates,and the tensile properties and deep drawing performance were measured.The results show that the occurrence of dynamic recrystallization was promoted,the grains were refined and the preferred orientation of the recrystallized grains was improved by large strain cross rolling.Compared with CBA and CCB rolling methods,CBB rolling method significantly reduced the orientation density of the typical Brass texture{110}?112?in the extruded plates.The orientation densities of Copper texture{112}?111?and Brass texture{110}?112?on theβorientation line in the CBB rolled plates were the lowest,and there were no typical texture features in the plates.Meanwhile,better deep drawing could be gained in the CBB rolled plates,and the mechanical properties of the 0°,45°and 90°directions were basically the same.The tensile strength,yield strength and elongation at room temperature for the CBB rolled plates were 617 MPa,523 MPa and over 20.1%,respectively.The deviation of the mechanical properties at different directions was less than 3%.展开更多
基金sponsored by the National Key Technology R&D Program for the 12th five-year plan(No.2011ZX05020-008)the China National Petroleum Corporation Logging Basic Research Project(No.2014A-3910)
文摘Tight sandstone has a certain anisotropy. Using ultrasonic measurements of samples in three different directions and related matched experiments, this study systematically analyzes the pore structure and anisotropy of tight sandstone samples obtained from oil fields and compares results with those of shale. Results firstly show that the anisotropy of tight sandstone is mainly related to the compositional layering and thin interbedding which occur in different sedimentary environments. Tight sandstone has typical transverse isotropic medium characteristics, Young’s modulus increases in different directions with increasing confining pressure, Poisson’s ratio change is not obvious, anisotropic coefficients decrease with increasing effective pressure, and a certain linear relationship exists between ε, γ, and δ. This article finally summarizes anisotropy in different areas, thereby providing a foundation for the use of suitable appraisal models in different regions. This research can be used as an experimental reference for logging evaluation, seismic data interpretation, and fracturing develop of tight sandstones.
基金Project(2017JJ2073) supported by the Natural Science Foundation of Hunan Province,China
文摘Transmission electron microscopy(TEM),electron backscattered diffraction imaging(EBSD)and X-ray diffractometry were used to analyze the microstructure and texture characteristics of Al-9.8Mg-1.5Li-0.4Mn alloy cross-rolled and extruded plates,and the tensile properties and deep drawing performance were measured.The results show that the occurrence of dynamic recrystallization was promoted,the grains were refined and the preferred orientation of the recrystallized grains was improved by large strain cross rolling.Compared with CBA and CCB rolling methods,CBB rolling method significantly reduced the orientation density of the typical Brass texture{110}?112?in the extruded plates.The orientation densities of Copper texture{112}?111?and Brass texture{110}?112?on theβorientation line in the CBB rolled plates were the lowest,and there were no typical texture features in the plates.Meanwhile,better deep drawing could be gained in the CBB rolled plates,and the mechanical properties of the 0°,45°and 90°directions were basically the same.The tensile strength,yield strength and elongation at room temperature for the CBB rolled plates were 617 MPa,523 MPa and over 20.1%,respectively.The deviation of the mechanical properties at different directions was less than 3%.
