红外变焦系统结构设计

为了模拟目标成像大小的变化过程,设计了一款17x的红外变焦系统,为保证系统在变焦过程中像面的稳定性,应用动态光学知识在Matlab中建立数学模型,得到变焦拟合曲线。重点针对变焦系统的结构进行了设计与分析,由物理制约条件出发分析了凸轮直径、工作转角及螺旋升角间的关系。实验表明,基于动态光学设计的凸轮曲线可以保证系统在变焦过程中像面稳定,成像质量良好。

SO_2 emission characteristics from co-firing of petroleum coke and coal in circulating fluidized bed

Combustion and sulfur retention experiments of mixed fuel of petroleum cokeand coal were conducted on a pilot-scale circulating fluidized bed (CFB) combustor with the thermalinput of 0. 6 MW. The effects of several parameters, such as the primary air percentage, excess aircoefficient, bed temperature, Ca/S molar ratio and mass ratio of petroleum coke to coal on SO_2emission were verified. Experimental results show that when the ratio of petroleum coke to coal inthe mixed fuel increases, the SO_2emission increases. The maximum SO_2 emission appears when purecoke burns. The SO_2 concentration in flue gas reduces with the increase in the primary airpercentage, excess air coefficient and Ca/S molar ratio for all kinds of fuel mixtures. Therangebetween 830 t and 850 t is the optimal temperature for sulfur retention during co-firing ofpetroleum coke and coal with the mass ratio R of 1 and 3 in CFB.

浅谈高职艺术专业摄影教学中需着重强调的几个问题

对学生的实际拍摄过程和作品分析发现,学生摄影作品中,艺术的体现的确存在相当程度的不足;在实际拍摄过程中,表现出的对单反相机驾驭操控能力的欠缺也普遍存在。目前摄影教学中表现出来的问题,不只是技术或者艺术哪一个单方层面的偏颇,过于推崇"技术流"或"艺术流"都是片面的,技术与艺术并重的"两条腿走路"才是应该提倡的教学和学习方法。

Research on the imaging of concrete defect based on the pulse compression technique

When the synthetic aperture focusing technology （SAFT） is used for the detection of the concrete, the signal-to-noise ratio （SNR） and detection depth are not satisfactory. Therefore, the application of SAFT is usually limited. In this paper, we propose an improved SAFT technique for the detection of concrete based on the pulse compression technique used in the Radar domain. The proposed method first transmits a linear frequency modulation （LFM） signal, and then compresses the echo signal using the matched filtering method, after which a compressed signal with a narrower main lobe and higher SNR is obtained. With our improved SAFT, the compressed signals are manipulated in the imaging process and the image contrast is improved. Results show that the SNR is improved and the imaging resolution is guaranteed compared with the conventional short-pulse method. From theoretical and experimental results, we show that the proposed method can suppress noise and improve imaging contrast, and can also be used to detect multiple defects in concrete.

Solidification process of conventional superalloy by confocal scanning laser microscope

The solidification process of a conventional superalloy, IN718, was investigated by confocal scanning laser microscope （CSLM）. The liquid fraction during solidification was obtained as a function of real time and temperature in reference with the in-situ observation. The characteristics of L→γ transformation were analyzed and the γ growing rate of each stage was also calculated. Scheil equation was employed to predict the segregation behavior, and the predict results are in consistence with the experimental results. As a result, the confocal scanning laser microscope shows a great potential for solidification process research.

PHASE AUTOFOCUSING ALGORITHM FOR COMPRESSED INVERSE SYNTHETIC APERTURE RADAR IMAGING

As same as the conventional inverse synthetic aperture radar（ISAR）, the compressed ISAR also requires the echo signal based motion compensation, which consists of the range alignment and the phase autofoeusing. A phase autofocusing algorithm for compressed ISAR imaging is presented. In the algorithm, phase autofocusing for the sparse ISAR echoes is accomplished using the eigenvector method. Experimental results validate the effectiveness of the algorithm.

基于二维医学影像推算三维人体姿态

针对三维人体姿态估计模型复杂,计算量偏大的问题,提出一种基于二维医学影像推算三维人体姿态的方法。在特定姿态下采集人体医学影像并进行二维影像姿态估计,得到人体各个骨骼的医学影像的长度信息。再在人体位置不发生改变的情况下,对任意姿态的人体采集图像并进行二维医学影像的人体姿态估计,得到骨骼在与相机透镜主光轴垂直平面上的投影的影像的近似长度,反推骨骼与该平面的夹角,最后从投影的影像位置反推骨骼的三维空间朝向。最后将得到的各个骨骼的空间朝向组合在一起,便得到了三维人体医学影像。使用此方法只需要对医学图像进行二维人体姿态估计,再加上一些三角函数、反三角函数的计算就可以从二维医学影像去推算三维人体姿态。与ICCV 2019中代表当今最高水平(State of the Art, SOTA)的三维人体姿态模型的方法相比,大大减少了计算量。

ISAR MOTION COMPENSATION USING MODIFIED DOPPLER CENTROID TRACKING METHOD

With regard to the phase compensation in inverse synthetic aperture radar (ISAR),the modified Doppler centroid tracking (MDCT) method is developed which applies the phase gradient autofocus (PGA) algorithm developed by Wahl[1]to improve the Doppler centroid tracking (DCT) method[2].When the phase compensation is performed,the proposed approach smartly eliminates the effect of the rotational phase component (RPC) on the estimation of the translational phase component (TPC) by circular shifting,windowing and iteration steps. After several iterations,the maximum likelihood estimation and compensation of the TPC of the target can be realized more effectively.The processing results of live data show that the proposed method can improve the imaging quality of ISAR significantly.

Entropy function optimization for radar imaging

The convergence performance of the minimum entropy auto-focusing（MEA） algorithm for inverse synthetic aperture radar（ISAR） imaging is analyzed by simulation. The results show that a local optimal solution problem exists in the MEA algorithm. The cost function of the MEA algorithm is not a downward-convex function of multidimensional phases to be compensated. Only when the initial values of the compensated phases are chosen to be near the global minimal point of the entropy function, the MEA algorithm can converge to a global optimal solution. To study the optimal solution problem of the MEA algorithm, a new scheme of entropy function optimization for radar imaging is presented. First, the initial values of the compensated phases are estimated by using the modified Doppler centroid tracking （DCT）algorithm. Since these values are obtained according to the maximum likelihood （ML） principle, the initial phases can be located near the optimal solution values. Then, a fast MEA algorithm is used for the local searching process and the global optimal solution can be obtained. The simulation results show that this scheme can realize the global optimization of the MEA algorithm and can avoid the selection and adjustment of parameters such as iteration step lengths, threshold values, etc.

Fluidized-bed pyrolysis of waste bamboo

Bamboo was a popular material substituting for wood, especially for one-off commodity in China. In order to recover energy and materials from waste bamboo, the basic characteristics of bamboo pyrolysis were studied by a thermogravimetric analyzer. It implied that the reaction began at 190-210℃, and the percentage of solid product deceased from about 25% to 17% when temperature ranged from 400℃ to 700℃. A lab-scale fluidized-bed furnace was setup to research the detailed properties of gaseous, liquid and solid products respectively. When temperature increased from 400℃ to 700℃, the mass percent of solid product decreased from 27% to 17% approximately, while that of syngas rose up from 19% to 35%. When temperature was about 500℃, the percentage of tar reached the top, about 31%. The mass balance of these experiments was about 93%-95%. It indicated that three reactions involved in the process： pyrolysis of exterior bamboo, pyrolysis of interior bamboo and secondary pyrolysis of heavy tar.

Synthesis and Characterization of Condensed Polynuclear Aromatic Resin Derived from Ethylene Tar

As a kind of low-cost and readily available industrial byproduct, ethylene tar （ET） was for the first time utilized for the preparation of heat-resistant condensed polynuclear aromatic resin （COPNAR）. The basic properties of ET and the resulted COPNAR were characterized by FT-IR, IH-NMR, TGA and elemental analysis. The test results showed that ET with high aromatic content （〉50%） was suitable for the synthesis of COPNAR with superior heat resistance. The average molecular structure of ET was obtained by means of the improved Brown-Ladner method, and the reaction mechanism was considered as an acid-catalyzed positive ion-typed polymerization. Our findings have provided a new route to develop ET into technology-added heat-resistant resins.

Effect of coal moisture content on coke’s quality and yields of products during coal carbonization

The coal with low moisture during carbonization could not only increase the yield of coke,but also promote the coke quality and reduce the energy consumption.In this paper,the influence of the moisture in the blend coal(1.8%10.13%)on the product yields and coke quality during coal carbonization were investigated.The results show that the coke yield is increased from 75.90%to 77.16%,and the coke qualities such as coke strength after reaction with CO2(CSR),coke reactivity index(CRI),fragmentation index(M25)and abrasion index(M10))are also improved when the moisture of the blend coal decreases from 10.13%to 1.80%in a bench scale reactor.Due to the secondary reaction,tar become lighter when the moisture is decreased.In order to further prove the above results,the blend coal with 1.8%and 9%10%(common moisture used in coke plant)moisture is carbonized in a coke oven with 6 m height,the results show that CRI are 23.4%and 27.3%,CRS are 67.1%and 62.2%under 1.8%and 9%10%moisture of blend coal.Moreover,the variation of the moisture in blend coal has a limited influence on dust emission at the ascension pipe and the charging car.

Effect of current density on corrosion resistance of micro-arc oxide coatings on magnesium alloy

Oxide coatings were prepared on magnesium alloys in electrolyte solution of Na2SiO3 at different current densities(3,4 and 5 A/cm 2 )with micro-arc oxidation process.X-ray diffractometry(XRD)results show that the oxide coatings formed on magnesium alloys are mainly composed of MgO and MgAl2O4 phases;in addition,the content of MgO increases with increasing the current density.The morphology and surface roughness of the coatings were characterized by confocal laser scanning microscopy (CLSM).The results show that the surface roughness(Ra)decreases with increasing the current density.Moreover,the electrochemical corrosion results prove that the MgO coating produced in the electrolyte Na2SiO3 at current density of 5 A/cm 2 shows the best corrosion resistance.

Effect of Ce on morphology of a(Al)-Al_2Cu eutectic in Al-Si-Cu alloy

The effect of Ce addition on the morphology of the α（Al）-Al2Cu eutectic in Al-Si-Cu alloy was investigated using thermal analysis, light microscopy, scanning electron microscopy, focused ion beam and energy dispersive analysis. The results show that the eutectic α（Al）-Al2Cu forms within small space between dendrites, silicon and AlSiFeMn plates. Eutectic Al2Cu is not lamellar but degenerated. However, Al2Cu in Ce-modified alloys is more compact. Ce partially dissolves in Al2Cu, which is a viable reason for the formation of coarser Al2Cu. The addition of Ce also increases the microhardness of theα（Al）-Al2Cu eutectic by almost 10%compared with the basic Al-Si-Cu alloy.

Temperature distribution and effect of low-density electric current on B2+O lamellar microstructure of Ti_2AlNb alloy sheet during resistance heating

The resistance heating method has been one of the prospective techniques for hot processing and welding techniques. The thermal behavior under different densities of electric current and the effect of electric current at temperature of 780 oC using low density of electric current of 6.70 A/mm^2 on the B2+O lamellar microstructure were investigated for Ti2AlNb alloy sheet. The stable temperature denoted a balanced state between the Joule heat and the dissipation of heat including heat conduction, convection and radiation while the distribution of temperature was nonuniform. The highest temperatures of electric current heating samples increased as the density of electric current was elevated. In order to understand the specific effect of electric current on B2+O microstructure, heat treatment for microstructural homogeneity was introduced to this study. After that, according to the microstructural observations by common characterization techniques in the resistance-heating sample and the isothermal furnace-heating sample after homogenizing treatment, few significant differences in content and orientation of phases can be directly and explicitly found except the thermal effect from the applied electric current. The results will provide reference to this prospective forming and welding techniques and the application for Ti2AlNb alloys using resistance heating in the near future.

Performance Anxiety and the Fight or Flight Syndrome

Performance Anxiety is perhaps the most common social fear. Also called Stage Fright, Performance Anxiety is the fear of being in front of an audience, and all of the corollaries that are associated with the condition. The condition can be almost debilitating, and is all the more devastating to a seasoned professional performer who continues to be afflicted by the situation. Although there are numerous causes as the root of Performance Anxiety in different people, a significant reason for Performance Anxiety is a behavioral pattern that psychoanalysts call the Fight or Flight Syndrome. This syndrome is the focus of this paper. This paper identifies a number of the symptoms of Performance Anxiety along with many of the false antidotes that are suggested by friends and associates. Evidence is presented to support the realization that most audiences are not the enemy. Recommendations and a treatment plan are suggested which are designed to alleviate Performance Anxiety issues and are based on principles of behavioral modification.

Catalytic cracking mechanisms of tar model compounds

B3LYP/6-31G(d,p) method was used to investigate the catalytic cracking mechanism of biomass tar model compound.Phenol,toluene and benzene were selected as the tar model compounds and CaO was selected as the catalyst.The pathways of tar compound radical absorbed by CaO were determined firstly through comparing enthalpy changes of the absorption,and then Mulliken population changes were analyzed.The results show that the absorption of tar model compound radical and CaO is an exothermic reaction.Formation of C—O—Ca is more easily than that of C—Ca—O and formation of Caromatic—Caromatic—Ca—O is more easily than that of Caromatic—C(O)—Ca—O.The C—C bond Mulliken populations in tar model compound radicals are reduced by 11.9%,10.5% and 15.5% in the case of a hydrogen atom removed,and those are 15.7%,14.3% and 16.3% in the case of two hydrogen atoms removed through the absorption of CaO.Catalytic ability of CaO acting on the tar model compound is in an order of phenol>benzene>toluene.

Synthesis of Polyalphaolefins on AlCl_3/TiCl_4 Catalyst

The oligomerzation reactions on different catalysts were investigated and discussed. 1-Octene, 1-decene, 1-do- decene, a mixture of olefins （with a mass ratio of w（l-octene）： w（1-decenc）：w（1-dodecene） equating to 30：40：30）, and the products from paraffin cracking were oligomerized on the AlCl3/TiC14 catalyst. The results indicated that the AlCl3 catalyst led to severe coking reaction. With an increase in carbon number of alpha-olefins, the freezing point of oligomers increased and the kinematic viscosity decreased. The oligomers formed from the mixed olefins and the paraffin cracking products showed higher kinematic viscosity. Normal paraffins contained in the cracked products could increase the freezing point of oligomers. Furthermore, the distillation range of oligomers obtained from the cracked products was close to those of oligo- mers originated from 1-octene and 1-decene, while the oligomers obtained from the mixed olefins and 1-dodecene had simi- lar distillation ranges.

THE REALIZATION OF THE PPP AUTOFOCUS METHOD IN PFA FOR SPOTLIGHT MODE SAR IMAGING

This paper first studies the phase errors for fine-resolution spotlight mode SAR imaging and decomposes the phase errors into two kinds, one is caused by translation and the other by rotation. Mathematical analysis and computer simulations show the above mentioned motion kinds and their corresponding damages on spotlight mode SAR imaging. Based on this analysis, a single PPP is introduced for spotlight mode SAR imaging with the PFA on the assumption that relative rotation between APC and imaged scene is uniform. The selected single point is used first to correct the quadratic and higher order phase errors and then to adjust the linear errors. After this compensation, the space-invariant phase errors caused by translation are almost corrected. Finally results are presented with the simulated data.

Choice of reference surfaces for machined surface roughness in milling of SiC_p/Al composites

In order to choose the appropriate reference surface on the machined surface roughness of Si Cp/Al composites, the cutting experiments of Si Cp/Al composites were carried out, and the machined surface topography was measured by OLS3000 Confocal laser scanning microscope. The 3D measured data of machined surface topography were analyzed by the area power spectrum density. The result shows that the texture of machined surface topography in milling of Si Cp/Al composites is almost isotropic. This is the reason that the values of Rq at different locations on the same machined surface are obviously different. Through the comparison of performance of different filtering methods, the robust least squares reference surface can be used to extract the surface roughness of SiC p/Al composites effectively.