川西石棉地区含金剪切带的地球化学标志及矿物组合

在扬子地台西缘的石棉地区 ,含金剪切带发育 ,并表现出明显的垂直分带特征 :由下而上依次为基底次级含金韧性剪切带→基底与盖层之间的含金滑脱韧性剪切带→盖层次级含金韧 -脆性剪切带 ,而各剪切带的特征各异 :地球化学标志 (由下而上 ;下同 )Pb、Zn→Te、As→Sb、As、S ;主要成矿元素Au、Pb(Zn)→Au→Au、Ag、Cu ;矿石中最常见矿物黄铁矿→黄铁矿→黝铜矿和黄铁矿。

Adiabatic shear fracture in Ti-6Al-4V alloy

Separated specimens of Ti-6Al-4V alloy were dynamically loaded at a strain rate of 3 900 s-1 using a split Hopkinson pressure bar（SHPB） apparatus.The fracture features of the separated specimens were investigated by a scanning electron microscope.The results show that adiabatic shear failure occurs in the tested specimens,and two typical areas（dimple and smooth areas） with different features are alternatively distributed on the whole fracture surface.The dimple areas originate from voids generation and coalescence,exhibiting ductile fracture characteristics.Simultaneously,ultrafine grains（UFGs） and microcracks among grains are observed on the smooth areas,indicating that the emergence of UFG areas is caused by the propagation of microcracks along grain boundaries and exhibits brittle fracture characteristics.Fracture occurring in adiabatic shear bands is not uniform and ultimate rupture is resulted from ductile and brittle fracture modes.

Microstructural evolution of 2519-T87 aluminum alloy obliquely impacted by projectile with velocity of 816 m/s

Target made of 2519-T87 aluminum alloy was obliquely impacted by a projectile. Microstructural evolution around the crater was investigated by optical microscopy （OM）, transmission electron microscopy （TEM）, and electron backscattered diffraction （EBSD）. The micro-hardness distribution near the crater after impact was studied. The results indicate that at the entering stage, the amount of adiabatic shear band （ASB） is the most, and the precipitates are as fine as those of the target material; the micro-hardness is higher than that at the other stages. At the stable-running stage, the amount of ASB reduces as the micro-bands increase; the precipitates tend to coarsen, which leads to the decrease of the micro-hardness. At the leaving stage, there is a large amount of micro-bands; the precipitates are refined, and the micro-hardness is higher than that at the stable-running stage. The difference in the micro-hardness of the impact stages is due to work hardening and precipitate coarsening, which is caused by adiabatic temperature rise in the alloy.

Casting effect on compressive brittleness of bulk metallic glass

An interesting phenomenon of cooling-rate induced brittleness in Zr52.5Cu17.9Ni14.6Al10Ti5 bulk metallic glass （BMG） was reported. It was found that the as-cast BMG specimens exhibited a brittle-ductile transition when the larger specimens were machined into smaller specimens through removing the cast-softening surface layer by layer. After compression tests, the as-machined small specimens, owing to the absence of the cast-softening surface, displayed highly dense and intersecting shear bands, and extensive plastic deformation. This is in contrast to the catastrophic failure and low deformability in the as-cast large specimens. More free volume was detected in the smaller as-fractured specimens, by differential scanning calorimetry, which may be attributed to the occurrence of strain softening and increased plasticity. Compared with the relatively smooth fracture surface in the smaller specimens, the larger specimens showed more diverse features on the fracture surface due to their graded structures.

Dynamic fracture of Ti-6Al-4V alloy in Taylor impact test

The dynamic fracture behaviors of Ti-6Al-4V alloy at high strain rate loading were investigated systemically through Taylor impact test, over the range of impact velocities from 145 m/s to 306 m/s. The critical impact velocity of fracture ranges from 217 m/s to 236 m/s. Smooth surfaces and ductile dimple areas were observed on the fracture surfaces. As the impact velocity reached 260 m/s, the serious melting regions were also observed on the fracture surfaces. Self-organization of cracks emerges when the impact velocity reaches 260 m/s, while some special cracks whose ＂tips＂ are not sharp but arc and smooth, and without any evidence of deformation or adiabatic shear band were also observed on the impact end surfaces. Examination of the sections of these special cracks reveals that the cracks expand along the two maximum shear stress directions respectively, and finally intersect as a tridimensional ＂stagger ridge＂ structure.

Microstructure and texture evolution of AZ31 magnesium alloy during large strain hot rolling

Commercial AZ31 magnesium alloy sheets were rolled by nearly 70% thickness reduction in one rolling pass at 823 K. The results show that ultrafine grains are distributed in both shear bands and surfaces of the rolled sheets. The grain size of the refined grain in the shear bands is 0.4-1 μm. The outstanding grain refinement is attained by dynamic recrystallization due to flow localization. The texture in middle layer of the sheet is basal texture with little change in intensity throughout the rolling process, while the texture on surface becomes a double-peak texture with basal poles splitting in the transverse direction（TD）. The relative intensity of the double-peak texture is 26.6, which is quite higher than that of the texture in the middle layer. The inhomogeneous strain distribution is responsible for the exceptional grain refinement and texture evolution.

Shear localization behavior in hat-shaped specimen of near-αTi−6Al−2Zr−1Mo−1V titanium alloy loaded at high strain rate

The microstructure characteristics in early stage shear localization of near-αTi−6Al−2Zr−1Mo−1V titanium alloy were investigated by split Hopkinson pressure bar(SHPB)tests using hat-shaped specimens.The microstructural evolution and deformation mechanisms of hat-shaped specimens were revealed by electron backscattered diffraction(EBSD)method.It is found that the nucleation and expansion of adiabatic shear band(ASB)are affected by both geometric and structural factors.The increase of dislocation density,structure fragment and temperature rise in the deformation-affected regions provide basic microstructural conditions.In addition to the dislocation slips,the extension twins detected in shear region also play a critical role in microstructural fragmentation due to twin-boundaries effect.Interestingly,the sandwich structure imposes a crucial influence on ASB,which finally becomes a mature wide ASB in the dynamic deformation.However,due to much larger width,the sandwich structure in the middle of shear region is also possible to serve as favorable nucleation sites for crack initiation.

疫情防控期间企业营销手段的应用研究

企业营销调研是现代营销不可或缺的重要环节,是企业市场营销活动的起点,贯穿于企业市场营销的全过程,为企业营销战略决策提供客观科学的依据。本文主要论述我司在疫情防控期间如何使用营销调研法,帮助企业有的放矢地精准开展企业市场营销活动。