电感耦合等离子体原子发射光谱法测定合金化热镀锌钢板镀层重量及合金化率

提出了一种用电感耦合等离子体原子发射光谱法（ICP-AES）测定合金化镀锌钢板镀层重量及合金化率的分析方法。将钢板镀层剥离下来,选择206.200、259.941、396.152 nm分别作为Zn、Fe、Al的分析谱线,在优化的试验条件下用ICP-AES测定剥离液中Zn、Fe、Al的含量。其信号强度与Zn、Fe、Al的质量浓度分别在0.054~500、0.0095~70、0.0454~5 mg/L范围内呈线性关系。方法的回收率在95%~105%之间,相对标准偏差在0.57%~1.2%之间,不同方法间测定值一致。

碱煮黑钨渣还原熔炼回收有价金属的研究

采用还原熔炼工艺处理碱煮黑钨渣,以合金形式回收Fe、Mn、W、Sn、Nb有价元素,并分离As、Pb等有害元素。研究了还原剂(石墨粉)用量、熔炼温度和时间等对熔炼效果的影响。实验结果表明:在还原剂用量为16%、熔炼温度为1550℃、熔炼时间为120 min的条件下,碱煮黑钨渣中Fe、Mn、W、Sn、Nb元素的合金化率分别达到了88.67%、56.28%、98.23%、67.74%、84.72%,As、Pb、Bi基本进入烟尘。

Microstructure evolution of spray-formed hypereutectic Al-Si alloys in semisolid reheating process

The Al-27%Si alloy was prepared by the spray forming process,and its microstructure evolution during the semisolid reheating process was investigated.The results show that,the primary Si phase coarsens during the reheating process and the coarsening rate increases with the increase of reheating temperature.The eutectic phase is produced in the molten region when quenched in the cold water.The microstructure evolution in the semisolid state can be divided into three stages.The remarkable characteristic of the first stage is only a solid-state phase transformation process.However,the region around the α（Al） matrix gradually melts in the second stage.The primary Si in the liquid phase coarsens obviously,and the eutectic phase is produced in the molten region when the specimens are quenched in cold water.In the last stage,the same thing as that in the second stage happens except that all the α（Al） matrixes are melted.

Effect of current frequency on properties of coating formed by microarc oxidation on AZ91D magnesium alloy

The microarc oxidation（MAO） coatings produced at different current frequencies on AZ91 D magnesium alloys were studied systematically. The morphologies, thickness, corrosion performances, and tribological properties of the coatings were investigated by the scanning electron microscopy, the electrochemical measurement system, and MS-T3000 friction test rig, respectively. The results show that the structure of the coatings becomes denser, and thickness becomes thinner with the increase of the current frequency. It is also found that the corrosion resistance of the coatings produced at higher frequency is improved greatly and the difference of the corrosion current density becomes small with increasing current frequency, which is similar to that of the coating thickness. The tribological test shows that the friction coefficient decreases with increasing the current frequency and the wear resistance of the coatings is influenced by both the thickness and structures. All these results were explained by analyzing the growing process of the MAO coating.

Current efficiency of recycling aluminum from aluminum scraps by electrolysis

Extracting aluminum from aluminum alloys in AlCl3-NaCl molten salts was investigated. Al coating was deposited on the copper cathode by the method of direct current deposition using aluminum alloys as anode. The purity of the deposited aluminum is about 99.7% with the energy consumption of 3-9 kW＆#183;h per kg Al, and the current efficiency is 44%-64% when the deposition process is carried out under 100 mA/cm2 for 4 h at 170 ＆#176;C. The effects of experimental parameters, such as molar ratio of AlCl3 to NaCl, cathodic current density and electrolysis time, on the current efficiency were studied. The molar ratio of AlCl3 to NaCl has little effect on the current efficiency, and the increase of deposition temperature is beneficial to the increase of current efficiency. However, the increase of current density or electrolysis time results in the decrease of current efficiency. The decrease of current efficiency is mainly related to the formation of dendritic or powder deposit of aluminum which is easy to fall into the electrolyte.

Growth and corrosion behaviors of thin anodic alumina membrane on AA5083 Al-Mg alloy in incalescent medium

A self-ordered porous film was fabricated on aluminum alloy in a ternary boric-sulfuric-oxalic acid electrolyte system. By means of voltage–time response, the oxidation process as well as the growth efficiency was studied. Field emission scanning electron microscopy（FE-SEM） was adopted to reveal the morphological and microstructural features of as-fabricated oxide layers. The corrosion protection properties of the films were investigated by electrochemical impedance spectroscopy and potentiodynamic polarization measurements. The results showed that increasing the concentration of the double ionic layer located at the oxide interface could accelerate the film growth rate. The anodic oxidative layer with thickness of 8-9 μm and pore diameter of 10-14 nm maintains the pattern and topography of workpieces, compared with the overall closed film with hierarchical structure. Both samples exhibited much lower corrosion current density after boil water sealing. Meanwhile, a superior stability could be achieved through raising the ambient temperature.

Dynamic behavior and fracture mode of TiAl intermetallics with different microstructures at elevated temperatures

Experimental studies were conducted on the tensile behaviors and fracture modes of TiAl（Ti-46.5Al-2Nb-2Cr） alloys with near gamma（NG） equiaxed and near lamellar（NL） microstructures over a temperature range from room temperature to 840 ℃ and a strain rate range of 0.001-1 350 s-1.The results indicate that the alloys are both temperature and strain rate dependent and they have a similar dependence.The dynamic strength is higher than the quasi-static strength but almost insensitive to high strain rate range of 320-1 350 s-1.The brittle-to-ductile transition temperature（BDTT） increases with increasing strain rates.NG TiAl yields obviously,while NL TiAl does not.Below BDTT,as the temperature increases,the fracture modes of the two alloys change from planar cleavage fracture to a mixture of transgranular and intergranular fractures,and finally to totally intergranular fracture.

Effects of alloying and deformation on microstructures and properties of Cu-Mg-Te-Y alloys

New copper alloys with high mechanical properties and high electrical conductivity were prepared, and the effects of addition of minor Mg and Y elements on microstructures and properties were studied. The high tensile strength of above 510 MPa, high elongation of 11%and high electrical conductivity of over 63%IACS can be simultaneously obtained in Cu-0.47Mg-0.20Te-0.04Y alloy after deforming and annealing treatment. Effects of purification together with the grain refining by Y and solid-solution strengthening by Mg are appropriate for enhancing mechanical properties and electrical conductivity of the copper alloys.

Effect of ruthenium on γ' precipitation behavior and evolution in single crystal superalloys

The effect of Ru on γ＇ precipitation behavior and evolution in single crystal superalloys with different Ru contents were investigated by scanning electron microscopy with energy dispersive spectroscopy,3D atomic probing,differential scanning calorimetry.The results show that the solvus of the γ＇ phase decreases gradually with increasing Ru content in the alloys by casting or by the same solution and aging treatments,the alloy with a larger Ru content yields a smaller γ＇ phase.The addition of Ru increases the growth rate and coarsening rate of the γ＇ phase.Ru mainly distributes in the γ phase,which causes more Re and Mo partition into the γ＇ phase,increasing the absolute value of mismatch and the rafting rate of the γ＇ phase.

Microstructure and mechanical properties of AZ31B magnesium alloy gas metal arc weld

Wrought magnesium alloy sheets were butt welded with gas metal arc welding process. Pores in the weld were investigated under different welding parameters, the causes of pore formation were systematically disposed, and the effects of porosity on the microstructure and mechanical properties of the joint were analyzed. The microstructure examination shows that the pores mainly appear close to the top or bottom part of the weld, and could connect to each other and lead to the formation of cracks in the welds. However, the pores can be controlled with proper welding parameters. The tensile testing results reveal that the average joint strength is close to or higher than that of the base metal. The microhardness in the weld can be even higher than that in the base metal due to the second ohase strengthening of β-Mg17（A1, Zn）12 formed in the weld.

Effect of purification treatment on corrosion resistance of Mg-Gd-Y-Zr alloy

Mg-Gd-Y-Zr alloys were purified by filtering purification with and without vacuum. The type, morphology, size distribution and volume fraction of inclusion were analyzed with OM and SEM. The effect of inclusion in Mg-Gd-Y-Zr alloys on anticorrosion ability was investigated with salt spray test and electrochemical test. The results show that the inclusions in the alloy can be removed effectively by filtering purification. The average size of inclusions in the alloys is decreased from 12.7 μm to 2.0 μm and the volume fraction of inclusions is reduced from 0.30% to 0.04%. With the decrease of the size of inclusions in the alloys, the corrosion rate of the alloys decreases dramatically from 38.8 g/（m 2 ·d） to 2.4 g/（m 2 ·d） in the salt spray test. The corrosion potential increases while the corrosion current decreases and the polarization resistance increases in the electrochemical tests, which indicates that the anticorrosion ability is improved.

Coarsening rate of microstructure in semi-solid aluminium alloys

The rate of microstructural coarsening of recrystallisation and partial melting (RAP) and cooling slope (CS) processed materials in the semi-solid state is compared with rates found in the literature.The rate of coarsening depended on the liquid fraction but RAP route 2014 alloy with 37% liquid coarsened slightly more slowly than the CS route 2014 alloy with a lower liquid fraction of 17%, contrary to expectations.For the CS route, an increase in liquid fraction resulted in faster coarsening.A modified 2014 alloy with Fe, Mn and Zn stripped out of the composition gave a relatively high coarsening rate.The coarsening rate was also relatively high for CS 201 alloy in comparison with either RAP 2014 or CS 2014.Low coarsening rates are thought to be associated with the presence of particles which inhibit the migration of liquid film grain boundaries.This could be the result of pinning or of the liquid film impeding diffusion at the boundary.

Microstructure evolution and its effect on flow stress of TC17 alloy during deformation in α+β two-phase region

The microstructure evolution and its effect on flow stress of TC17 alloy during deformation in the α+β two-phase region were investigated via microstructure characterization and isothermal compression tests. Results showed that the spheroidized rate of α phase at 820 and 850℃ slightly increased with increasing strain. With increasing deformation temperature, the spheroidized rate of α phase showed a slight increasing trend, but the volume fraction of α phase significantly decreased. The flow stress at 780 ℃ and 1 s^-1 decreased continuously and steady state condition was not achieved up to strain of 1.2 due to dislocation annihilation and α lamellae rotation. Under this condition, the dynamic spheroidization was retarded. At the deformation temperatures of 820 and 850℃, and a strain rate of 1 s^-1, a steady state flow stress was observed at strains above 0.8 due to the balance between work hardening and dynamic softening. The dynamic softening was attributed to the α lamellae rotation, dynamic recovery and a little spheroidization.

Online evaluation of electroless deposition rate by electrochemical noise method

Continuous noise resistance calculation(CNRC)technique was used for online determination of the electroless nickel deposition rate on zirconium pretreated magnesium alloy.For this purpose,the noise resistance(R_n) variation with time was calculated for the pretreated alloy surface in the electroless plating solution.The CNRC results were described by energy dispersive X-ray spectroscopy(EDS)and scanning electron microscopy(SEM)techniques.Also,potentiodynamic polarization and gravimetric measurements were used for determination of the electroless deposition rate at the same time period and the results were compared with the CNRC results.The Rn variation with plating time shows that the electroless plating consists of different stages with various deposition rates.The results of the CNRC and polarization methods were not in acceptable agreement due to the limitations of the polarization method for online monitoring of the deposition rate.However,the results of the gravimetric measurements were in complete agreement with the CNRC technique and so,the CNRC can be considered as suitable tool for online evaluation of the electroless deposition rate.

Effect of addition of Si on microstructure, mechanical properties, bio-corrosion and cytotoxicity of Mg-6Al-1Zn alloy

The Mg-6Al-4Zn alloy was fabricated by mechanical alloying(MA)and hot pressing to serve as biodegradable metal implant.The influence of addition of 1%Si(mass fraction)on the microstructure,mechanical properties and bio-corrosion behavior of Mg-6Al-1Zn alloy was studied using X-ray diffractometry,transmission electron microscopy,compression test,as well as immersion,electrochemical test and MTT assay.The results showed that the addition of 1%Si to Mg-6Al-1Zn alloy led to the formation of fine Mg2Si phase with polygonal shape,and increased compressive strength,elongation and improved corrosion resistance.Furthermore,the cell viability of Saos-2 cells has been improved by addition of 1%Si to Mg-6Al-1Zn alloy.According to the results,the magnesium ions released in the methylthiazol tetrazolium(MTT)test have not shown any cell toxicity.All these indicated that the addition of 1%Si improved the properties of Mg-6Al-4Zn alloy for using as a biodegradable implant.

Effect of cooling rate on solidification microstructure and mechanical properties of TiB2-containing TiAl alloy

Effects of cooling rate and 0.25 at.%TiB2 addition on solidification microstructure and mechanical properties of Ti−48Al−2Cr−2Nb alloys fabricated by the investment casting with different thicknesses were studied.The results show that with the cooling rate increasing from 37 to 2×102 K/s,the solidification path of the studied alloys is unchanged.The grain size of the matrix alloy is refined from 650 to 300μm,while the grain size of Ti−48Al−2Cr−2Nb−TiB2 is reduced from 550 to 80μm.The lamellar spacing of matrix alloy is reduced from 360 to 30 nm with increasing the cooling rate from 37 to 2×102 K/s,while TiB2 addition shows little refinement effect on the lamellar spacing.Ti−48Al−2Cr−2Nb−TiB2 sample under medium cooling rate(69 K/s)exhibits superior microhardness(HV 550)and ultimate tensile strength(570 MPa)among the studied alloys.The refined grain size,lamellar spacing and fine TiB2 particles could account for the favorable mechanical properties of the studied TiB2-containing alloy.The microstructure evolution was discussed in light of cooling rate,constitutional supercooling and borides addition.

Effect of Mg and Si on intermetallic formation and fracture behavior of pure aluminum-galvanized carbon-steel joints made by weld-brazing

Commercial pure aluminum and galvanized carbon steel were lap-welded using the weld-brazing(WB)technique.Three types of aluminum filler materials(4043,4047,and 5356) were used for WB.The joint strength and intermetallic compounds at the interface of three series of samples were analyzed and compared.Depending on the Si content,a variety of ternary Al-Fe-Si intermetallic compounds(IMCs) such as Fe_(4)(Al,Si)_(13),Fe_(2) Al_(8) Si(τ_(5)),and Fe_(2) Al_(9) Si_(2)(τ_(6)) were formed at the interface.Mg element in 5356 filler material cannot contribute to the formation of Al-Fe intermetallic phases due to the positive mixing enthalpy of Mg-Fe.The presence of Mg enhances the hot cracking phenomenon near the Al-Fe intermetallic compound at the interface.Zn coating does not participate in intermetallic formation due to its evaporation during WB.It was concluded that the softening of the base metal in the heat-affected zone rather than the IMCs determines the joint efficiency.

Effect of solidification rate on MC-type carbide morphology in single crystal Ni-base superalloy AM3

In order to study the effect of the withdrawing rate on carbide morphology,MC-type carbide in single crystal superalloy AM3 was systematically investigated with sample growth rates from 3.5 μm/s to 500 μm/s.The carbide morphologies were investigated by scanning electron microscopy(SEM),and the electron probe microanalysis(EPMA) was used to characterize the carbide composition.The results indicate that the solidification rate is the important factor governing MC carbide growth morphology,size and distribution,composition and growth mechanism.With the increase of withdrawing rate,nodular,rod-like,Chinese script types of carbide morphology are observed.For the low withdrawing rate,with the increase of withdrawing rate,the carbide size becomes larger.For the case of dendritic interface,the carbide size becomes smaller with refinement of dendrites as withdrawing rate increases.The volume fraction of carbides increases with the withdrawing rate increasing.

In situ thermomechanical processing to avoid grain boundary precipitation and strength-ductility loss of age hardening alloys

To avoid grain boundary(GB) precipitation during aging, a new strategy of in situ thermomechanical processing for age hardening alloys was proposed. Specifically, high-density nanoscale precipitates were introduced into ultrafine grain(UFG) interiors of 7075 Al alloy by equal-channel-angular(ECAP) processing at 250 ℃ for 8 passes, thus avoiding GB precipitation. Tensile test results indicated that the UFG 7075 Al alloy exhibits superior mechanical properties(yield strength of 350 MPa, ultimate tensile strength of 500 MPa, uniform elongation of 18% and tensile ductility of 19%) compared with the UFG 1050 Al counterpart(yield strength of 170 MPa, ultimate tensile strength of 180 MPa, uniform elongation of 2.5% and tensile ductility of 7%). Fracture surface morphology studies revealed numerous homogeneous micro shear bands in necking shrinkage areas of both UFG 7075 Al and 1050 Al alloys, which are controlled by cooperative GB sliding. Moreover, the introduction of nanoscale precipitates in UFG 7075 Al matrix weakened the tendency of shear fracture, resulting in a higher tensile ductility and more homogeneous deformation. Different from the GB precipitation during postmortem aging, in situ thermomechanical treatment dynamically formed GBs after precipitation, thus avoiding precipitation on GBs.

Effects of precipitation strengthening heat treatment for Al-Mg alloy

The corrosions resulting from defects in painting layers frequently occur in Al alloys, so the application of corrosion preventing systems is also very important. Optimum conditions in terms of electrochemistry in relation to solution treatment, quenching and artificial aging treatment were established in order to optimize precipitation strengthening conditions intended to enhance the strength of Al alloys. Slow strain rate tests （SSRT） at various applied potentials were conducted in potential range from -1.8 to 0.5 V. The results show that the maximum tensile strengths, elongations and time-to-fracture are shown to be high values. After precipitation strengthening heat treatment, a tendency appear that time-to-fracture increases as elongation increases. In the potential range from -1.3 V to -0.7 V, the specimens show excellent mechanical properties, and thus this range is considered to be a corrosion prevention range.